2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT SEAT ASSEMBLY (for RHD)
  1. for Manual Seat:
    Remove the front seat assembly (Click here).

  1. for Power Seat:
    Remove the front seat assembly (Click here).


3. REMOVE CONSOLE BOX ASSEMBLY (for RHD)
  1. for Automatic Transmission:
    Remove the console box assembly (Click here).

  1. for Manual Transmission:
    Remove the console box assembly (Click here).

  1. w/ Refrigerated Cool Box:
    Remove the console box assembly (Click here).


4. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
  1. for Manual Seat Type:
    Remove the rear No. 2 seat assembly (Click here).

  1. for Power Seat Type:
    Remove the rear No. 2 seat assembly (Click here).

  1. for Face to Face Seat Type:
    Remove the rear No. 2 seat assembly (Click here).


5. REMOVE REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)
  1. for 60/40 Split Slide Walk-in Seat Type LH Side:
    Remove the rear No. 1 seat assembly (Click here).

  1. for 60/40 Split Slide Walk-in Seat Type RH Side:
    Remove the rear No. 1 seat assembly (Click here).


6. REMOVE REAR NO. 1 SEATBACK ASSEMBLY (w/ Rear No. 1 Seat)
  1. for 60/40 Split Double-folding Seat Type LH Side:
    Remove the rear No. 1 seatback assembly (Click here).

  1. for 60/40 Split Double-folding Seat Type RH Side:
    Remove the rear No. 1 seatback assembly (Click here).


7. REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

B238730E01

HINT:
Use the same procedure for all rear No. 1 floor step covers.

  1. Using a screwdriver, detach the 2 claws and remove the rear No. 1 floor step cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


8. REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

B238731
  1. Remove the 2 bolts and quarter scuff plate.


9. REMOVE QUARTER SCUFF PLATE RH (for RHD, w/ Rear No. 2 Seat)

HINT:
Use the same procedure described for the LH side.


10. REMOVE REAR DOOR SCUFF PLATE LH

B238733E01
  1. Put protective tape around the rear door scuff plate.

  1. Using a screwdriver, detach the 3 clips, 6 claws and 2 guides and remove the rear door scuff plate.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


11. REMOVE REAR DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure described for the LH side.


12. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

B238780
  1. Remove the rear door opening trim weatherstrip.


13. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover.


14. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

B240044

HINT:
Use the same procedure for the other front luggage compartment trim cover.

  1. Detach the 4 claws and remove the cap.

  1. B238749E01
    Remove the bolt, luggage hold belt striker and front luggage compartment trim cover.
    Text in Illustration 
    *1
    Luggage Hold Belt Striker


15. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)

B238750
  1. Detach the clip and remove the No. 1 deck board.


16. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)

B238748
  1. Detach the 5 clips and 4 claws and remove the rear floor mat rear support plate.


17. REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)

B238764
  1. Remove the 3 bolts and floor side rail.


18. REMOVE FLOOR SIDE RAIL RH (w/ Deck Rail)

HINT:
Use the same procedure described for the LH side.


19. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)

  1. Detach the 4 claws and remove the rear floor carpet.

    B238751E01

    Text in Illustration 
    *A
    w/o Deck Rail
    *B
    w/ Deck Rail
    *C
    for Face to Face Seat Type
    -
    -


20. REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

B238752

HINT:
Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.

  1. Detach the 3 claws and remove the rear No. 1 seat outer lap belt anchor cover.


21. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

B181695

HINT:
Use the same procedure for the other No. 1 luggage compartment trim hook.

  1. Remove the luggage compartment trim hook by turning it clockwise.


22. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

B238754E01

HINT:
Use the same procedure for the other No. 1 tonneau cover holder cap.

  1. Using a screwdriver, detach the 2 claws and remove the No. 1 tonneau cover holder cap.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


23. REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

B240051E01

HINT:
Use the same procedure for the other front deck side trim cover.

  1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


24. REMOVE ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

B238757E01

HINT:
Use the same procedure for all assist grip plugs.

  1. Using a screwdriver, detach the 2 claws and remove the assist grip plug.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


25. REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

B238758

HINT:
Use the same procedure for the other assist grip.

  1. Remove the 2 bolts and assist grip.


26. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

  1. w/o Rear No. 2 Seat:

    1. B238753
      Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    2. B238756
      Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.

    3. Remove the 4 bolts and 2 screws.

    4. Detach the 5 clips and 8 claws.

    5. Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.

      B238755

  1. w/ Rear No. 2 Seat:

    1. B238753
      Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    2. B238759
      Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

    3. Remove the 2 bolts and 2 screws.

    4. Detach the 4 clips and 8 claws and remove the deck trim side panel.

      B238760


27. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH

B238745
  1. Move the rear shoulder belt anchor adjuster to the lowest position.

  1. Detach the 2 clips and 2 guides.

  1. Pass the rear No. 1 seat outer belt floor anchor through the front quarter trim panel and remove the front quarter trim panel.


28. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

B238732E01
  1. Put protective tape around the door scuff plate.

  1. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


29. REMOVE DOOR SCUFF PLATE ASSEMBLY RH (for RHD)

HINT:
Use the same procedure described for the LH side.


30. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

  1. B238493
    Detach the 3 claws.

  1. Remove the fuel lid lock control cable assembly and fuel lid lock open lever sub-assembly.


31. REMOVE FRONT FLOOR CARPET ASSEMBLY

  1. for LHD:

    1. B238502
      Detach the 6 clamps and fold back the front floor carpet from the floor carpet hooks.

  1. for RHD:

    1. B238504
      Detach the 12 clamps and fold back the front floor carpet from the floor carpet hooks.


32. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

  1. B238500
    Turn the cable counterclockwise and remove the cable from the retainer.

  1. B238498
    Turn the lock retainer counterclockwise and remove the lock retainer.

  1. for LHD:

    1. Using a clip remover, detach the clamp labeled <A>.

    2. Detach the 13 clamps and remove the fuel lid lock control cable.

      B238494E01

  1. for RHD:

    1. Using a clip remover, detach the 3 clamps labeled <A>.

    2. Detach the 14 clamps and remove the fuel lid lock control cable.

      B238506E01

← REMOVAL (Aug 2013 – Jul 2014)INSTALLATION (Aug 2013 – Jul 2014) →