INSTALLATION
Removal / installation · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| 1.
INSTALL TRANSFER ASSEMBLY
|
 |
for 1KD-FTV:
Install the transfer assembly with the 8 bolts and 2 brackets.
-
Torque:
- 24 N*m{
245 kgf*cm
, 18 ft.*lbf
}
- NOTICE:
- Take care not to damage the adaptor rear oil seal with the transfer input gear spline.
except 1KD-FTV:
Install the transfer assembly with the 8 bolts and bracket.
-
Torque:
- 24 N*m{
245 kgf*cm
, 18 ft.*lbf
}
- NOTICE:
- Take care not to damage the adaptor rear oil seal with the transfer input gear spline.
| 2.
INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY |
 |
Align the input shaft with the clutch disc and install the transmission to the engine.
Install the 4 bolts.
-
Torque:
- 72 N*m{
730 kgf*cm
, 52 ft.*lbf
}
| 3.
INSTALL STIFFENER PLATE LH |
 |
- Install the stiffener plate with the 4 bolts.
-
Torque:
- for bolt A:
- 37 N*m{
380 kgf*cm
, 27 ft.*lbf
}
- for bolt B:
- 69 N*m{
701 kgf*cm
, 50 ft.*lbf
}
| 4.
INSTALL STIFFENER PLATE RH |
 |
- Install the stiffener plate with the 4 bolts.
-
Torque:
- for bolt A:
- 37 N*m{
380 kgf*cm
, 27 ft.*lbf
}
- for bolt B:
- 69 N*m{
701 kgf*cm
, 50 ft.*lbf
}
| 5.
INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR |
 |
Install the mounting insulator with the 4 bolts.
-
Torque:
- 65 N*m{
663 kgf*cm
, 48 ft.*lbf
}
| 6.
INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
 |
Install the frame crossmember with the 4 bolts and 4 nuts.
-
Torque:
- 72 N*m{
734 kgf*cm
, 53 ft.*lbf
}
Install the 4 bolts to the rear No. 1 engine mounting insulator.
-
Torque:
- 30 N*m{
306 kgf*cm
, 22 ft.*lbf
}
| 7.
INSTALL FRONT SUSPENSION MEMBER BRACKET LH |
 |
Install the member bracket with the 4 bolts.
-
Torque:
- 33 N*m{
337 kgf*cm
, 24 ft.*lbf
}
| 8.
INSTALL FRONT SUSPENSION MEMBER BRACKET RH |
 |
Install the member bracket with the 4 bolts.
-
Torque:
- 33 N*m{
337 kgf*cm
, 24 ft.*lbf
}
| 9.
INSTALL STARTER ASSEMBLY |
 |
Install the starter (Click here).
| 10.
CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY |
 |
Connect the release cylinder with the 2 bolts.
-
Torque:
- 12 N*m{
120 kgf*cm
, 9 ft.*lbf
}
| 11.
INSTALL TRANSFER AND MANUAL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY |
 |
Install the 3 breather hoses to the shift lever retainer and transfer adapter and attach the clamp.
| 12.
CONNECT WIRE HARNESS |
 |
Connect the 2 connectors and attach the 4 clamps.
| 13.
INSTALL PROPELLER SHAFT ASSEMBLY |
 |
Install the propeller shaft (Click here).
| 14.
INSTALL FRONT PROPELLER SHAFT ASSEMBLY |
 |
Install the front propeller shaft (Click here).
| 15.
INSTALL FRONT EXHAUST PIPE ASSEMBLY |
 |
Install the front exhaust pipe (Click here).
| 16.
ADD MANUAL TRANSMISSION OIL |
|
| 17.
INSTALL TRANSFER CASE LOWER PROTECTOR |
 |
Install the transfer case lower protector with the 4 bolts.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
| 18.
INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY |
 |
Cover the shift lever cap with a cloth.
Press down on the shift lever cap and rotate it clockwise to install it.
- HINT:
- Apply MP grease to the tip of the shift lever.
| 19.
INSTALL NO. 1 SHIFT AND SELECT LEVER BOOT |
 |
Install the boot with the 4 screws and 2 clips.
| 20.
INSTALL CENTER FLOOR CARPET ASSEMBLY (for Bench Seat Type) |
 |
Install the center floor carpet assembly with the 4 bolts.
-
Torque:
- 7.0 N*m{
71 kgf*cm
, 61 in.*lbf
}
| 21.
INSTALL FRONT SEAT ASSEMBLY (for Bench Seat Type) |
 |
(Click here)
| 22.
INSTALL CONSOLE BOX (for Bench Seat Type) |
 |
(Click here)
| 23.
INSTALL CONSOLE PANEL SUB-ASSEMBLY (for Separate Type) |
 |
for Manual Transmission: (Click here)w/ Refrigerated Cool Box: (Click here)
| 24.
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
|
| 25.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
 |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).