Home › Engine / Hybrid System › 5L-E (ENGINE MECHANICAL) › VALVE CLEARANCE
RM27T0E _51 Engine / Hybrid System _053661 5L-E ENGINE MECHANICAL _0260480 VALVE CLEARANCE N

5L-E ENGINE MECHANICAL  VALVE CLEARANCE  ADJUSTMENT  


PROCEDURE

Hide 1.REMOVE RESONATOR WITH AIR CLEANER CAP SUB-ASSEMBLY

Hide 17130 2.REMOVE INTAKE AIR CONNECTOR SUB-ASSEMBLY

Hide 11201 3.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 4.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A112064

Turn the crankshaft pulley and align its groove with the timing pointer.


b.

Check that the valve lifters for the No. 1 cylinder are loose and the valve lifters for the No. 4 cylinder are tight.

If not, turn the crankshaft 1 revolution (360°) and align the mark as above.


Hide 5.INSPECT VALVE CLEARANCE

a.
A374959E01
1.135,1.844 0.906,1.844 0.906,1.844 0.906,1.302 false 0.552,1.115 0.594,0.427 0.594,0.427 0.802,0.427 false 1.917,1.094 1.958,0.406 1.958,0.406 2.167,0.406 false 1.802,1.917 1.573,1.917 1.573,1.917 1.573,1.344 false 0.802,0.302 1.115,0.5 0.313,0.198 10 false *1 2.188,0.281 2.5,0.479 0.313,0.198 10 false *2 1.135,1.729 1.448,1.927 0.313,0.198 10 false *3 1.823,1.771 2.135,1.969 0.313,0.198 10 false *4

Check only the valves indicated in the illustration.

i.

Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

Standard Valve Clearance (Cold):
Item Specified Condition
Intake 0.20 to 0.30 mm (0.00787 to 0.0118 in.)
Exhaust 0.40 to 0.50 mm (0.0158 to 0.0197 in.)


Text in Illustration
*1 No. 1 EX
*2 No. 3 EX
*3 No. 1 IN
*4 No. 2 IN


ii.

Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement adjusting shim.



b.
A112064

Turn the crankshaft 1 revolution (360°) and align the mark as above.


c.
A374960E01
2.729,0.573 3.146,0.156 false 1.229,1 1.229,0.438 1.229,0.438 1.021,0.438 true 2.573,1.01 2.573,0.344 2.573,0.344 2.365,0.344 true 2.01,1.75 2.25,1.75 2.25,1.75 2.25,1.281 true 2.719,1.844 2.958,1.844 2.958,1.844 2.958,1.271 true 2.188,0.24 2.5,0.438 0.313,0.198 10 false *2 1.844,1.635 2.156,1.833 0.313,0.198 10 false *3 2.552,1.719 2.865,1.917 0.313,0.198 10 false *4 0.833,0.333 1.146,0.531 0.313,0.198 10 false *1

Check only the valves indicated in the illustration.

Text in Illustration
*1 No. 2 EX
*2 No. 4 EX
*3 No. 3 IN
*4 No. 4 IN

i.

Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

Standard Valve Clearance (Cold):
Item Specified Condition
Intake 0.20 to 0.30 mm (0.00787 to 0.0118 in.)
Exhaust 0.40 to 0.50 mm (0.0158 to 0.0197 in.)



ii.

Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement adjusting shim.



Hide 6.ADJUST VALVE CLEARANCE

a.
A374961E01
1.76,0.406 1.76,0.094 1.76,0.094 1.552,0.094 false 1.271,0.01 1.75,0.188 0.479,0.177 10 true SST

Remove the adjusting shim.

i.

Turn the crankshaft so that the cam lobe of the camshaft on the valve being adjusted points upward.


ii.

Using SST, press down the valve lifter.

SST
09248-64011  


iii.

Position the notch of the valve lifter so that it faces the exhaust manifold side.


iv.
A056810E02
2,1.24 2.156,1.438 0.156,0.198 10 false .

Remove the adjusting shim with a screwdriver and magnet hand.



b.
A056812E02
2.656,1.115 2.813,1.313 0.156,0.198 10 false .

Determine the replacement adjusting shim size according to the formula and charts below.

i.

Using a micrometer, measure the thickness of the removed shim.


ii.

Calculate the thickness of a new shim so that the valve clearance comes within the specified value.

T = Thickness of removed shim

A = Measured valve clearance

N = Thickness of new shim

Intake N = T + (A - 0.25 mm (0.00984 in.))
Exhaust N = T + (A - 0.45 mm (0.0177 in.))


iii.

Select a new shim with a thickness as close as possible to the calculated value.

HINT:

Shims are available in 17 sizes in increments of 0.05 mm (0.00197 in.), from 2.50 mm (0.0984 in.) to 3.30 mm (0.130 in.).


A374964E01
3.75,0 4.063,0.198 0.313,0.198 10 false *1 1.031,0.333 1.344,0.531 0.313,0.198 10 false *2 0.5,0.625 0.813,0.823 0.313,0.198 10 false *3

Text in Illustration
*1 Adjusting Shim Selection Chart (Intake) *2 Removed shim thickness mm (in.)
*3 Measure clearance mm (in.) - -

New Shim Thickness mm (in.):
Shim No. Thickness Shim No. Thickness
01 2.50 (0.0984) 46 2.95 (0.116)
42 2.55 (0.100) 26 3.00 (0.118)
06 2.60 (0.102) 47 3.05 (0.120)
43 2.65 (0.104) 31 3.10 (0.122)
11 2.70 (0.106) 48 3.15 (0.124)
44 2.75 (0.108) 36 3.20 (0.126)
16 2.80 (0.110) 49 3.25 (0.128)
45 2.85 (0.112) 41 3.30 (0.130)
21 2.90 (0.114)


Intake valve clearance (Cold):

0.20 to 0.30 mm (0.00787 to 0.0118 in.)


EXAMPLE:

A 2.80 mm (0.110 in.) shim is installed and the measured clearance is 0.350 mm (0.0138 in.). Replace the 2.80 mm (0.110 in.) shim with a No. 21 shim.

A374965E01
3.813,0 4.125,0.198 0.313,0.198 10 false *1 1.052,0.313 1.365,0.51 0.313,0.198 10 false *2 0.49,0.625 0.802,0.823 0.313,0.198 10 false *3

Text in Illustration
*1 Adjusting Shim Selection Chart (Exhaust) *2 Removed Shim Thickness mm (in.)
*3 Measure Clearance mm (in.) - -

New Shim Thickness mm (in.):
Shim No. Thickness Shim No. Thickness
01 2.50 (0.0984) 46 2.95 (0.116)
42 2.55 (0.100) 26 3.00 (0.118)
06 2.60 (0.102) 47 3.05 (0.120)
43 2.65 (0.104) 31 3.10 (0.122)
11 2.70 (0.106) 48 3.15 (0.124)
44 2.75 (0.108) 36 3.20 (0.126)
16 2.80 (0.110) 49 3.25 (0.128)
45 2.85 (0.112) 41 3.30 (0.130)
21 2.90 (0.114)


Exhaust valve clearance (Cold):

0.40 to 0.50 mm (0.0157 to 0.0196 in.)


EXAMPLE:

A 2.80 mm (0.110 in.) shim is installed and the measured clearance is 0.350 mm (0.0138 in.). Replace the 2.80 mm (0.110 in.) shim with a No. 11 shim.



c.

Install a new adjusting shim.

i.

Install a new adjusting shim to the valve lifter.


ii.

Remove SST.



d.

Recheck valve clearance.


Hide 11201 7.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 17130 8.INSTALL INTAKE AIR CONNECTOR SUB-ASSEMBLY

Hide 9.INSTALL RESONATOR WITH AIR CLEANER CAP SUB-ASSEMBLY