Home › Engine / Hybrid System › 1KD-FTV (FUEL) › COMMON RAIL › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053669 1KD-FTV FUEL _0260568 COMMON RAIL A

1KD-FTV FUEL  COMMON RAIL  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.



PROCEDURE

Hide 23810A 1.INSTALL COMMON RAIL ASSEMBLY

a.

Install the common rail and No. 2 intake manifold insulator with the 2 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


b.

Connect the fuel pressure sensor connectors and pressure discharge valve connector.


Hide 23804C 2.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

Hide 23770 3.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

a.
A224423E01
1.829,0.681 2.007,0.824 0.178,0.143 10 *1 1.817,0.774 1.763,0.774 1.763,0.774 1.679,0.647 false

Temporarily install the No. 2 nozzle leakage pipe with the 4 bolts.


b.

Temporarily install a new gasket and the union bolt.

Text in Illustration
*1 Union Bolt


c.

Tighten the 4 bolts and union bolt.

Torque:
for bolt : 13 N*m (130 kgf*cm, 9 ft.*lbf)
for union bolt : 21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Connect the 3 fuel hoses.


Hide 23704 4.INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY

Hide 17118 7.INSTALL MANIFOLD STAY WITH VACUUM SWITCHING VALVE

Hide 26100G 8.INSTALL INTAKE AIR CONNECTOR WITH DIESEL THROTTLE BODY ASSEMBLY (w/o EGR System)

Hide 17871A 10.INSTALL AIR CONNECTOR STAY (w/o EGR System)

Hide 23701 11.INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/o EGR System)

Hide 22267A 12.INSTALL THROTTLE BODY BRACKET (w/o EGR System)

Hide 17113E 13.INSTALL NO. 1 INTAKE PIPE (w/o EGR System)

Hide 25709E 14.CONNECT NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/o EGR System)

Hide 87245A 15.CONNECT INLET HEATER WATER HOSE (w/o EGR System)

Hide 25800 16.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System)

a.

Install the electric EGR control valve assembly (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>EGR VALVE>INSTALLATION).


Hide 17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 18.ADD ENGINE COOLANT (w/ EGR System with EGR Cooler)

Hide 20.INSPECT FOR COOLANT LEAK (w/ EGR System with EGR Cooler)