Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › 2015.06–2017.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1784/84  Steering Sensor Signal Malfunction  


DESCRIPTION

The steering angle sensor signal is sent to the suspension control ECU through CAN communication system. When there is a communication malfunction, this DTC is detected by the diagnosis function.

DTC Code DTC Detection Condition Trouble Area
C1784/84 A steering angle sensor signal malfunction is detected, or a steering angle sensor power source malfunction signal is detected for 5 seconds or more.
·

Steering angle sensor (spiral cable sub-assembly)

·

Steering angle sensor power source circuit

·

Suspension control ECU



WIRING DIAGRAM

C214176E13
1.99,0.906 2.792,1.104 0.802,0.198 10 false from Battery 2.01,1.854 2.99,2.052 0.979,0.198 10 false from IG Circuit 5.479,0.917 5.802,1.083 0.323,0.167 10 false BAT 5.5,1.875 5.719,2.083 0.219,0.208 10 false IG 0.573,3.417 2.177,3.635 1.604,0.219 10 false Suspension Control ECU 1.635,4.281 4.25,4.5 2.615,0.219 10 false : CAN Communication System 5.177,3.479 6.625,3.729 1.448,0.25 10 false Steering Angle Sensor 0.583,3.25 0.927,3.417 0.344,0.167 10 false A49 5.198,0.76 5.323,0.938 0.125,0.177 10 false 6 5.198,1.729 5.344,1.885 0.146,0.156 10 false 5 3.677,1.063 4.167,1.219 0.49,0.156 10 false ECU-B 3.458,2 4.396,2.177 0.938,0.177 10 false ECU-IG NO. 1 5.177,3.323 5.458,3.49 0.281,0.167 10 false G33 5.479,2.438 5.917,2.615 0.438,0.177 10 false ESS 5.198,2.292 5.396,2.49 0.198,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Do not remove the steering angle sensor from the spiral cable sub-assembly.

·

When replacing the spiral cable sub-assembly, confirm that the replacement part is of the correct specification.



HINT:

If DTC C1782/82 is output at the same time as C1784/84, perform troubleshooting for C1782/82 first (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>C1782/82).


PROCEDURE

1.CHECK DTC

b.

Perform a road test.


c.

Check if DTCs C1784/84 and U0126/71 are output (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>DTC CHECK / CLEAR).

Result
Condition Proceed to
DTC is not output or only DTC 1784/84 is output A
DTCs 1784/84 and U0126/71 are output B



A

2.CHECK DTC (VEHICLE STABILITY CONTROL SYSTEM)

B

2.CHECK DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for steering angle sensor malfunction DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Condition Proceed to
DTC is not output A
DTC is output B



A

3.CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, BAT, ESS)

B

3.CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, BAT, ESS)
a.

Disconnect the G33 steering angle sensor connector.


b.
U148293E03
2.052,1.385 2,1.729 true 2.302,1.354 2.552,1.677 true 1.323,1.385 1.135,1.708 true 0.094,0.094 0.313,0.313 0.219,0.219 10 false *a 2.458,1.708 2.896,1.885 0.438,0.177 10 false BAT 1.958,1.729 2.219,1.906 0.26,0.177 10 false IG 0.948,1.729 1.271,1.906 0.323,0.177 10 false ESS 0.344,1.021 0.646,1.198 0.302,0.177 10 false G33

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G33-5 (IG) - Body ground Ignition switch ON 11 to 14 V
G33-6 (BAT) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
G33-2 (ESS) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor)


c.

Check that the steering angle sensor connector is not deformed or corroded.

OK:

No deformation or corrosion.


HINT:

If the steering angle sensor connector is defective, replace the spiral cable sub-assembly.




OK

4.READ VALUE USING INTELLIGENT TESTER (STEERING ANGLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (STEERING ANGLE)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / Air suspension / Data List.

Air Suspension
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Steering Angle Steering angle/
Min.: -49152.0 deg
Max.: 49150.5 deg
Actual steering angle
Turned left: reading increases
Turned right: reading decreases
-

OK:

Steering wheel turning angle value changes when steering wheel is turned.




OK

REPLACE SUSPENSION CONTROL ECU

NG