Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  U1002  Lost Communication with Gateway Module (Power Management1)  


DESCRIPTION

·

The power management control ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the V2 bus.

·

When the power management control ECU receives a response signal from the ECUs connected to the V2 bus, the power management control ECU recognizes and memorizes that the ECU is connected to the V2 bus. Based on this memorized data, the power management control ECU monitors for malfunctions in the ECUs connected to the V2 bus when communicating with those ECUs. If the power management control ECU cannot receive response signals from the ECUs that have been memorized as those connected to the V2 bus, the power management control ECU determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 Lost communication with the gateway module (Power Management1).
·

V2 bus circuit

·

Parking assist ECU CAN branch wire or connector*1

·

Clearance warning ECU assembly CAN branch wire or connector*2

·

Driving support ECU assembly CAN branch wire or connector*3

·

Stabilizer control ECU CAN branch wire or connector*4

·

Seat belt control ECU CAN branch wire or connector*3

·

Blind spot monitor sensor LH CAN branch wire or connector*5

·

Suspension control ECU CAN branch wire or connector*6

·

Headlight swivel ECU assembly CAN branch wire or connector*7

·

Power management control ECU CAN main wire or connector

·

Parking assist ECU*1

·

Clearance warning ECU assembly*2

·

Driving support ECU assembly*3

·

Stabilizer control ECU*4

·

Seat belt control ECU*3

·

Blind spot monitor sensor LH*5

·

Suspension control ECU*6

·

Headlight swivel ECU assembly*7

·

Air conditioning amplifier assembly*8

·

Power management control ECU

·

No. 1 junction connector

·

No. 3 junction connector

·

No. 5 junction connector

·

No. 6 junction connector*5

·

No. 7 junction connector



*1: w/ Side Monitor System

*2: w/ TOYOTA Parking Assist-sensor System

*3: w/ Pre-crash Safety System

*4: w/ Kinetic Dynamic Suspension System

*5: w/ Blind Spot Monitor System

*6: w/ Air Suspension System

*7: for LED Headlight

*8: except 1KD-FTV, 1GR-FE and Manual Transmission System


WIRING DIAGRAM

C334439E02
4.007,0.294 4.105,0.431 0.098,0.137 10 2 4.007,0.747 4.182,0.884 0.175,0.137 10 13 3.232,0.294 3.328,0.431 0.096,0.137 10 3 3.156,0.747 3.327,0.884 0.172,0.137 10 14 4.007,3.895 4.105,4.031 0.098,0.137 10 1 4.007,4.348 4.182,4.485 0.175,0.137 10 12 3.23,3.895 3.328,4.031 0.098,0.137 10 6 3.152,4.348 3.327,4.485 0.175,0.137 10 17 4.007,5.759 4.105,5.896 0.098,0.137 10 1 4.007,6.212 4.182,6.349 0.175,0.137 10 12 3.232,5.759 3.328,5.896 0.096,0.137 10 5 3.156,6.212 3.327,6.349 0.172,0.137 10 16 1.349,0.294 1.607,0.433 0.258,0.139 10 40 1.349,0.747 1.551,0.886 0.203,0.139 10 39 0.792,0.393 1.211,0.530 0.419,0.137 10 CANH 0.819,0.837 1.212,0.974 0.393,0.137 10 CANL 0.383,1.21 0.849,1.373 0.467,0.163 10 I7 0.383,1.392 2.034,1.757 1.652,0.364 10 Parking Assist ECU*1 1.349,5.772 1.607,5.911 0.258,0.139 10 29 1.349,6.226 1.551,6.365 0.203,0.139 10 28 0.792,5.872 1.211,6.008 0.419,0.137 10 CANH 0.819,6.316 1.212,6.453 0.393,0.137 10 CANL 0.383,6.689 0.849,6.852 0.467,0.163 10 G123 0.383,6.871 2.034,7.235 1.652,0.364 10 Stabilizer Control ECU*6 2.891,7.123 3.358,7.286 0.467,0.163 10 G95 2.891,7.305 4.499,7.670 1.607,0.364 10 No. 3 Junction Connector 1.349,2.102 1.607,2.241 0.258,0.139 10 3 1.013,2.202 1.213,2.339 0.200,0.137 10 R1 1.015,2.646 1.213,2.783 0.198,0.137 10 R2 0.383,3.019 1.249,3.182 0.867,0.163 10 I1*4, G154*5 0.383,3.201 2.034,3.565 1.652,0.364 10 Clearance Warning ECU Assembly*2 0.383,4.819 1.249,4.982 0.867,0.163 10 G25 0.383,5.001 2.034,5.366 1.652,0.364 10 Air Conditioning Amplifier Assembly*7 1.349,2.556 1.551,2.695 0.203,0.139 10 5 4.007,2.102 4.105,2.239 0.098,0.137 10 4 4.007,2.556 4.182,2.693 0.175,0.137 10 15 3.232,2.102 3.328,2.239 0.096,0.137 10 5 3.156,2.556 3.327,2.693 0.172,0.137 10 16 5.678,2.102 5.849,2.241 0.172,0.139 10 39 5.678,2.556 5.849,2.695 0.172,0.139 10 17 5.971,2.202 6.457,2.339 0.485,0.137 10 CA2H 5.971,2.646 6.450,2.783 0.479,0.137 10 CA2L 5.635,3.019 6.076,3.156 0.441,0.137 10 G119 5.635,3.166 6.969,3.530 1.334,0.364 10 Driving Support ECU Assembly*3 2.9,4.795 3.367,4.958 0.467,0.163 10 G98 2.9,4.977 4.510,5.341 1.610,0.364 10 No. 1 Junction Connector 0.189,7.404 2.692,7.543 2.503,0.139 10 *1: w/ Side Monitor System 0.189,7.669 3.081,7.808 2.892,0.139 10 *2: w/ TOYOTA Parking Assist-sensor System 3.04,7.99 7.078,8.301 4.038,0.311 10 *7: except 1KD-FTV, 1GR-FE and Manual Transmission System 3.04,8.354 7.064,8.665 4.024,0.311 10 *12: for 1KD-FTV, 1GR-FE and Manual Transmission System 0.189,7.934 2.692,8.073 2.503,0.139 10 *3: w/ Pre-crash Safety System 0.189,8.21 2.692,8.349 2.503,0.139 10 *4: for 4 Sensor Type 0.189,8.539 2.692,8.678 2.503,0.139 10 *5: for 8 Sensor Type 3.236,7.669 5.939,7.808 2.703,0.139 10 *6: w/ Kinetic Dynamic Suspension System 1.349,3.9 1.607,4.039 0.258,0.139 10 11 1.349,4.353 1.551,4.492 0.203,0.139 10 12 0.792,3.999 1.211,4.136 0.419,0.137 10 CANH 0.819,4.443 1.212,4.580 0.393,0.137 10 CANL 5.076,0.294 5.845,0.433 0.769,0.139 10 26*12, 12*7 5.076,0.747 5.845,0.886 0.769,0.139 10 25*12, 11*7 5.945,0.302 6.590,0.438 0.645,0.137 10 CA2H*12 5.945,0.106 6.549,0.242 0.603,0.137 10 CA3P*7 5.972,0.94 6.643,1.077 0.670,0.137 10 CA2L*12 5.972,1.109 6.577,1.245 0.604,0.137 10 CA3N*7 5.496,1.187 5.937,1.324 0.441,0.137 10 G51 5.496,1.334 6.767,1.698 1.271,0.364 10 Power Management Control ECU

C294684E04
4.007,0.364 4.105,0.501 0.098,0.137 10 6 4.007,0.817 4.182,0.954 0.175,0.137 10 17 3.232,0.364 3.328,0.501 0.096,0.137 10 3 3.156,0.817 3.327,0.954 0.172,0.137 10 14 5.743,0.364 5.850,0.503 0.107,0.139 10 1 5.743,0.817 5.850,0.956 0.107,0.139 10 2 5.971,0.463 6.457,0.600 0.485,0.137 10 CANH 5.971,0.907 6.450,1.044 0.479,0.137 10 CANL 5.537,1.28 5.978,1.417 0.441,0.137 10 G118 5.537,1.427 7.068,1.791 1.531,0.364 10 Seat Belt Control ECU*3 2.9,1.276 3.367,1.439 0.467,0.163 10 G95 2.728,0.817 3.195,0.980 0.467,0.163 10 *8 2.728,0.364 3.195,0.527 0.467,0.163 10 *8 2.728,3.311 3.195,3.474 0.467,0.163 10 *8 2.728,2.858 3.195,3.020 0.467,0.163 10 *8 1.653,1.01 2.120,1.173 0.467,0.163 10 *9 1.653,0.556 2.120,0.719 0.467,0.163 10 *9 2.9,1.458 4.510,1.822 1.610,0.364 10 No. 3 Junction Connector 0.287,8.033 2.790,8.172 2.503,0.139 10 *3: w/ Pre-crash Safety System 0.287,8.298 2.790,8.437 2.503,0.139 10 *8: w/ Blind Spot Monitor System 0.287,8.563 2.790,8.702 2.503,0.139 10 *9: w/o Blind Spot Monitor System 3.093,8.033 5.596,8.172 2.503,0.139 10 *10: w/ Air Suspension System 3.093,8.298 5.596,8.437 2.503,0.139 10 *11: for LED Headlight 3.208,1.985 3.304,2.122 0.096,0.137 10 1 3.132,2.439 3.303,2.576 0.172,0.137 10 12 3.208,4.461 3.304,4.598 0.096,0.137 10 2 3.132,4.915 3.303,5.051 0.172,0.137 10 13 1.324,6.262 1.583,6.401 0.258,0.139 10 12 1.324,6.716 1.527,6.855 0.203,0.139 10 13 0.768,6.362 1.187,6.498 0.419,0.137 10 CANH 0.795,6.806 1.188,6.942 0.393,0.137 10 CANL 0.359,7.179 0.825,7.341 0.467,0.163 10 A58 0.359,7.361 2.010,7.696 1.652,0.335 10 Headlight Swivel ECU Assembly*11 3.983,1.985 4.081,2.122 0.098,0.137 10 2 3.983,2.439 4.158,2.576 0.175,0.137 10 13 5.728,1.985 5.826,2.124 0.097,0.139 10 2 5.728,2.439 5.826,2.578 0.097,0.139 10 7 5.947,2.085 6.367,2.222 0.419,0.137 10 CA1P 5.947,2.534 6.388,2.671 0.441,0.137 10 CA1N 5.611,2.878 6.052,3.015 0.441,0.137 10 R42 5.625,3.053 6.896,3.418 1.271,0.364 10 Blind Spot Monitor Sensor LH*8 3.983,4.453 4.081,4.590 0.098,0.137 10 3 3.983,4.907 4.158,5.044 0.175,0.137 10 14 5.728,4.453 5.826,4.592 0.097,0.139 10 7 5.728,4.907 5.826,5.046 0.097,0.139 10 8 5.947,4.553 6.367,4.690 0.419,0.137 10 CANH 5.947,5.002 6.388,5.139 0.441,0.137 10 CANL 5.611,5.346 6.052,5.483 0.441,0.137 10 A49 5.625,5.493 6.896,5.858 1.271,0.364 10 Suspension Control ECU*10 3.208,2.887 3.304,3.024 0.096,0.137 10 3 3.132,3.341 3.303,3.477 0.172,0.137 10 14 3.983,6.262 4.081,6.399 0.098,0.137 10 1 3.983,6.716 4.158,6.853 0.175,0.137 10 12 3.208,6.262 3.304,6.399 0.096,0.137 10 4 3.132,6.716 3.303,6.853 0.172,0.137 10 15 5.719,6.262 5.826,6.401 0.107,0.139 10 3 5.719,6.716 5.826,6.855 0.107,0.139 10 2 5.947,6.262 6.432,6.399 0.485,0.137 10 CANH 5.947,6.904 6.426,7.040 0.479,0.137 10 CANL 5.513,7.179 5.954,7.315 0.441,0.137 10 G102 5.513,7.326 7.106,7.690 1.593,0.364 10 No. 7 Junction Connector 2.876,3.768 3.342,3.931 0.467,0.163 10 R47 2.876,3.95 4.680,4.314 1.804,0.364 10 No. 6 Junction Connector*8 2.876,7.174 3.342,7.337 0.467,0.163 10 A73 2.876,7.326 4.486,7.690 1.610,0.364 10 No. 5 Junction Connector

CAUTION / NOTICE / HINT

HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)
2.CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)
a.
U169939E06
2.01,1.188 2.552,0.615 2.552,0.615 2.698,0.615 true 1.646,1 1.458,0.552 1.458,0.552 1.365,0.552 true 1.958,1.188 2.375,0.417 2.375,0.417 2.51,0.417 true 2.521,1.021 2.833,1.167 2.833,1.167 2.865,1.167 true 2.146,1.115 2.365,1.792 2.365,1.792 2.51,1.792 true 2.208,1.115 2.542,1.594 2.542,1.594 2.667,1.594 true 0.042,0 0.219,0.167 0.177,0.167 10 false *a 1.917,0.135 2.208,0.302 0.292,0.167 10 false G51 2.906,1.083 3.302,1.25 0.396,0.167 10 false AM22 1.031,0.479 1.375,0.646 0.344,0.167 10 false GND 2.719,0.531 3.26,0.708 0.542,0.177 10 false CA2L*A 2.531,0.333 3.146,0.51 0.615,0.177 10 false CA2H*A 2.542,1.719 3.083,1.896 0.542,0.177 10 false CA3P*B 2.698,1.51 3.313,1.688 0.615,0.177 10 false CA3N*B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition Resistance: Malfunction
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 54 to 69 Ω Below 53 Ω: Short in line
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G51-26 (CA2H) - G51-1 (AM22) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G51-25 (CA2L) - G51-1 (AM22) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G51-26 (CA2H) - G51-6 (GND) Engine switch off 200 Ω or higher Below 200 Ω: Ground short
G51-25 (CA2L) - G51-6 (GND) Engine switch off 200 Ω or higher Below 200 Ω: Ground short

except 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition Resistance: Malfunction
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 54 to 69 Ω Below 53 Ω: Short in line
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G51-12 (CA3P) - G51-1 (AM22) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G51-11 (CA3N) - G51-1 (AM22) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G51-12 (CA3P) - G51-6 (GND) Engine switch off 200 Ω or higher Below 200 Ω: Ground short
G51-11 (CA3N) - G51-6 (GND) Engine switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*A for 1KD-FTV, 1GR-FE and Manual Transmission System
*B except 1KD-FTV, 1GR-FE and Manual Transmission System
*a Component with harness connected
(Power Management Control ECU)

Result
Result Proceed to
NG
·

Open in CAN main bus line


A
NG
·

Short in line

·

+B short

·

Ground short


B
OK C



A

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

B

19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR SIDE)

C

70.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND BODY GROUND)
3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.
U148797E05
2.656,0.917 2.594,0.917 2.594,0.917 2.313,1.083 true 2.656,1.469 2.594,1.469 2.594,1.469 2.313,1.313 true 2.719,0.844 3.156,1.021 0.438,0.177 10 false CANH 0.406,1.094 0.729,1.271 0.323,0.177 10 false G95 0.094,0 0.302,0.177 0.208,0.177 10 false *a 2.719,1.396 3.156,1.573 0.438,0.177 10 false CANL

Disconnect the G95 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-1 (CANH) - G95-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

NG

5.CONNECT CONNECTOR
4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
a.
U148798E05
2.094,1.104 2.448,0.688 2.448,0.688 2.542,0.688 true 2.083,1.313 2.542,1.677 2.542,1.677 2.635,1.677 true 2.583,0.615 3.021,0.792 0.438,0.177 10 false CANH 2.677,1.594 3.115,1.771 0.438,0.177 10 false CANL 0.344,0.927 0.667,1.104 0.323,0.177 10 false G95 0.104,0.042 0.313,0.219 0.208,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-3 (CANH) - G95-14 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

10.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the G95 No. 3 junction connector.



NEXT

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)
6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)
a.
U148799E04
2.635,0.615 2.573,0.615 2.573,0.615 2.208,1.094 true 2.635,1.781 2.573,1.781 2.573,1.781 2.208,1.302 true 2.688,0.531 3.125,0.708 0.438,0.177 10 false CANH 0.271,0.938 0.594,1.115 0.323,0.177 10 false G98 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 2.688,1.708 3.125,1.885 0.438,0.177 10 false CANL

Disconnect the G98 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-2 (CANH) - G98-13 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

NG

8.CONNECT CONNECTOR
7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U148800E03
2.667,0.938 2.604,0.938 2.604,0.938 2.323,1.094 false 2.667,1.479 2.604,1.479 2.604,1.479 2.323,1.313 false 2.719,0.854 3.156,1.031 0.438,0.177 10 false CANH 0.302,0.969 0.625,1.146 0.323,0.177 10 false G98 0.094,0.031 0.302,0.208 0.208,0.177 10 false *a 2.719,1.396 3.156,1.573 0.438,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-1 (CANH) - G98-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

8.CONNECT CONNECTOR
a.

Reconnect the G98 No. 1 junction connector.



NEXT

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (POWER MANAGEMENT CONTROL ECU - NO. 1 JUNCTION CONNECTOR)
9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (POWER MANAGEMENT CONTROL ECU - NO. 1 JUNCTION CONNECTOR)
a.
C348088E01
0.646,1.177 1.083,1.5 0.438,0.323 1.969,1.281 2.583,0.573 2.583,0.573 2.708,0.573 true 2.042,1.302 2.688,0.906 2.688,0.906 2.813,0.906 true 1.302,2 1.458,2 1.458,2 1.802,1.438 true 1.083,1.813 1.24,1.813 1.24,1.813 1.719,1.448 true 0.083,0.156 0.396,0.354 0.313,0.198 10 false *a 2.75,0.5 3.313,0.74 0.563,0.24 10 false CA3P*B 2.844,0.833 3.396,1.094 0.552,0.26 10 false CA3N*B 0.542,1.719 1.167,1.948 0.625,0.229 10 false CA2H*A 0.771,1.927 1.396,2.156 0.625,0.229 10 false CA2L*A 0.729,1.26 1.354,1.49 0.625,0.229 10 false G51

Disconnect the G51 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 108 to 132 Ω

except 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-25 (CA3N) Engine switch off 108 to 132 Ω


Text in Illustration
*A for 1KD-FTV, 1GR-FE and Manual Transmission System
*B except 1KD-FTV, 1GR-FE and Manual Transmission System
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (POWER MANAGEMENT CONTROL ECU - NO. 1 JUNCTION CONNECTOR)

10.CONNECT CONNECTOR
a.

Reconnect the G95 No. 3 junction connector.



NEXT

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
a.
U148801E03
2.677,0.948 2.615,0.948 2.615,0.948 2.333,1.104 false 2.667,1.479 2.604,1.479 2.604,1.479 2.323,1.313 false 2.719,0.875 3.156,1.052 0.438,0.177 10 false CANH 0.344,0.917 0.646,1.094 0.302,0.177 10 false A73 0.094,0.01 0.302,0.188 0.208,0.177 10 false *a 2.719,1.396 3.156,1.573 0.438,0.177 10 false CANL

Disconnect the A73 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A73-1 (CANH) - A73-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)

Result
Result Proceed to
OK (w/ Blind Spot Monitor System) A
OK (w/o Blind Spot Monitor System) B
NG C



A

12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

B

16.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

C

17.CONNECT CONNECTOR
12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
a.
U148796E03
2.635,0.625 2.573,0.625 2.573,0.625 2.198,1.104 false 2.635,1.802 2.573,1.802 2.573,1.802 2.198,1.302 false 2.688,0.531 3.125,0.708 0.438,0.177 10 false CANH 0.302,0.938 0.625,1.115 0.323,0.177 10 false A73 0.052,0.042 0.26,0.219 0.208,0.177 10 false *a 2.698,1.74 3.135,1.917 0.438,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A73-2 (CANH) - A73-13 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

13.CONNECT CONNECTOR
13.CONNECT CONNECTOR
a.

Reconnect the A73 No. 5 junction connector.



NEXT

14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U148802E01
2.7,0.785 3.134,0.925 0.434,0.140 10 CANH 0.34,1.151 0.615,1.290 0.275,0.139 10 R47 0.053,0.086 0.266,0.264 0.213,0.178 10 *a 2.672,1.506 3.105,1.647 0.434,0.140 10 CANL 2.673,0.859 2.558,0.859 2.558,0.859 2.324,1.095 false 2.644,1.594 2.53,1.594 2.53,1.594 2.336,1.338 false

Disconnect the R47 No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R47-1 (CANH) - R47-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)



OK

15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U148803E01
0.34,1.151 0.615,1.290 0.275,0.139 10 R47 2.7,0.573 3.134,0.713 0.434,0.140 10 CANH 0.053,0.086 0.266,0.264 0.213,0.178 10 *a 2.7,1.695 3.134,1.836 0.434,0.140 10 CANL 2.673,0.647 2.558,0.647 2.558,0.647 2.089,1.095 false 2.673,1.783 2.558,1.783 2.558,1.783 2.1,1.338 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R47-3 (CANH) - R47-14 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)



OK

REPLACE NO. 6 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

16.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U148804E03
2.646,0.615 2.583,0.615 2.583,0.615 2.208,1.094 false 2.635,1.813 2.573,1.813 2.573,1.813 2.198,1.313 false 2.688,0.531 3.125,0.708 0.438,0.177 10 false CANH 0.281,0.938 0.604,1.115 0.323,0.177 10 false A73 0.052,0.042 0.26,0.219 0.208,0.177 10 false *a 2.677,1.74 3.115,1.917 0.438,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A73-2 (CANH) - A73-13 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

17.CONNECT CONNECTOR
a.

Reconnect the A73 No. 5 junction connector.



NEXT

18.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 7 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
18.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 7 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U148311E02
2.25,0.25 2.188,0.25 2.188,0.25 1.406,0.875 false 2.51,1.594 2.448,1.594 2.448,1.594 1.771,1.073 false 2.292,0.167 2.729,0.344 0.438,0.177 10 false CANH 0.469,0.885 0.833,1.063 0.365,0.177 10 false G102 0.104,0.01 0.313,0.188 0.208,0.177 10 false *a 2.542,1.521 2.979,1.698 0.438,0.177 10 false CANL

Disconnect the G102 No. 7 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G102-3 (CANH) - G102-2 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 Junction Connector)



OK

REPLACE NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR SIDE)
a.
U169939E06
2.01,1.188 2.552,0.615 2.552,0.615 2.698,0.615 true 1.646,1 1.458,0.552 1.458,0.552 1.365,0.552 true 1.958,1.188 2.375,0.417 2.375,0.417 2.51,0.417 true 2.521,1.021 2.833,1.167 2.833,1.167 2.865,1.167 true 2.146,1.115 2.365,1.792 2.365,1.792 2.51,1.792 true 2.208,1.115 2.542,1.594 2.542,1.594 2.667,1.594 true 0.042,0 0.219,0.167 0.177,0.167 10 false *a 1.917,0.135 2.208,0.302 0.292,0.167 10 false G51 2.906,1.083 3.302,1.25 0.396,0.167 10 false AM22 1.031,0.479 1.375,0.646 0.344,0.167 10 false GND 2.719,0.531 3.26,0.708 0.542,0.177 10 false CA2L*A 2.531,0.333 3.146,0.51 0.615,0.177 10 false CA2H*A 2.542,1.719 3.083,1.896 0.542,0.177 10 false CA3P*B 2.698,1.51 3.313,1.688 0.615,0.177 10 false CA3N*B

Disconnect the A73 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 108 to 132 Ω
G51-26 (CA2H) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-25 (CA2L) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-26 (CA2H) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-25 (CA2L) - G51-1 (AM22) Engine switch off 6 kΩ or higher

except 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-11 (CA3N) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-12 (CA3P) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G51-1 (AM22) Engine switch off 6 kΩ or higher


Text in Illustration
*A for 1KD-FTV, 1GR-FE and Manual Transmission System
*B except 1KD-FTV, 1GR-FE and Manual Transmission System
*a Component with harness connected
(Power Management Control ECU)

Result
Result Proceed to
OK A
NG (w/ Blind Spot Monitor System) B
NG (w/o Blind Spot Monitor System) C



A

20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)

B

29.CONNECT CONNECTOR

C

44.CONNECT CONNECTOR
20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)
NOTICE:

For vehicles without an air suspension system, go to "Check for Short in CAN Bus Wires (No. 5 Junction Connector - Headlight Swivel ECU Assembly)".


a.
U149023E03
2.083,1.146 2.458,0.354 2.458,0.354 2.677,0.354 false 2.073,1.365 2.458,1.792 2.458,1.792 2.594,1.792 false 2.208,2.948 2.292,3.156 2.292,3.156 2.417,3.156 false 1.635,2.5 1.521,2.177 1.521,2.177 1.406,2.177 false 0.406,0.99 0.667,1.167 0.26,0.177 10 false A73 2.729,0.281 3.135,0.458 0.406,0.177 10 false CANH 2.635,1.719 3.021,1.896 0.385,0.177 10 false CANL 2.469,3.083 2.76,3.26 0.292,0.177 10 false BAT 1.135,2.104 1.365,2.281 0.229,0.177 10 false CG 0.406,2.698 0.688,2.875 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A73-3 (CANH) - A73-14 (CANL) Engine switch off 200 Ω or higher
A73-3 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
A73-14 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
A73-3 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
A73-14 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)
*b Front view of DLC3



OK

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)

NG

23.CONNECT CONNECTOR
21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)
NOTICE:

For vehicles without a halogen headlight, go to "Check for Short in CAN Bus Wires (No. 5 Junction Connector - No. 7 Junction Connector)".


a.
U149024E03
1.969,1.146 2.469,0.354 2.469,0.354 2.688,0.354 false 1.958,1.375 2.469,1.802 2.469,1.802 2.604,1.802 false 2.208,2.948 2.292,3.156 2.292,3.156 2.417,3.156 false 1.646,2.521 1.531,2.198 1.531,2.198 1.417,2.198 false 0.396,2.688 0.677,2.865 0.281,0.177 10 false G48 0.396,0.99 0.656,1.167 0.26,0.177 10 false A73 2.729,0.281 3.135,0.458 0.406,0.177 10 false CANH 2.635,1.719 3.021,1.896 0.385,0.177 10 false CANL 2.458,3.094 2.75,3.271 0.292,0.177 10 false BAT 1.156,2.115 1.385,2.292 0.229,0.177 10 false CG 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A73-4 (CANH) - A73-15 (CANL) Engine switch off 200 Ω or higher
A73-4 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
A73-15 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
A73-4 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
A73-15 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)
*b Front view of DLC3



OK

22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

NG

25.CONNECT CONNECTOR
22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
a.
U149025E03
2.292,1.156 2.458,0.365 2.458,0.365 2.677,0.365 false 2.302,1.365 2.458,1.792 2.458,1.792 2.594,1.792 false 2.208,2.948 2.292,3.156 2.292,3.156 2.417,3.156 false 1.646,2.51 1.531,2.188 1.531,2.188 1.417,2.188 false 0.396,2.698 0.677,2.875 0.281,0.177 10 false G48 0.406,0.99 0.667,1.167 0.26,0.177 10 false A73 2.729,0.281 3.135,0.458 0.406,0.177 10 false CANH 2.625,1.729 3.01,1.906 0.385,0.177 10 false CANL 2.458,3.083 2.75,3.26 0.292,0.177 10 false BAT 1.167,2.104 1.396,2.281 0.229,0.177 10 false CG 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A73-1 (CANH) - A73-12 (CANL) Engine switch off 108 to 132 Ω
A73-1 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
A73-12 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
A73-1 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
A73-12 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

27.CONNECT CONNECTOR
23.CONNECT CONNECTOR
a.

Reconnect the A73 No. 5 junction connector.



NEXT

24.CHECK FOR SHORT IN CAN BUS WIRES (SUSPENSION CONTROL ECU)
24.CHECK FOR SHORT IN CAN BUS WIRES (SUSPENSION CONTROL ECU)
a.
U148708E03
2.031,1.135 2.198,0.656 2.198,0.656 2.281,0.656 false 2.396,0.906 2.302,0.906 2.302,0.906 2.094,1.146 false 1.646,2.51 1.49,2.208 1.49,2.208 1.406,2.208 false 2.229,2.938 2.438,3.104 2.438,3.104 2.521,3.104 false 2.323,0.583 2.729,0.75 0.406,0.167 10 false CANL 2.448,0.854 2.896,1.021 0.448,0.167 10 false CANH 0.448,1 0.75,1.177 0.302,0.177 10 false A49 0.448,2.698 0.771,2.875 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.135,2.135 1.375,2.313 0.24,0.177 10 false CG 2.552,3.031 2.99,3.208 0.438,0.177 10 false BAT

Disconnect the A49 suspension control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A49-7 (CANH) - A49-8 (CANL) Engine switch off 54 to 69 Ω
A49-7 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
A49-8 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
A49-7 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
A49-8 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Suspension Control ECU)
*b Front view of DLC3



OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SUSPENSION CONTROL ECU (CANH, CANL)

25.CONNECT CONNECTOR
a.

Reconnect the A73 No. 5 junction connector.



NEXT

26.CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT SWIVEL ECU ASSEMBLY)
26.CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT SWIVEL ECU ASSEMBLY)
a.
U148723E04
2.51,1.677 2.615,1.677 2.615,1.677 2.792,0.969 false 2.875,0.354 2.76,0.354 2.76,0.354 2.667,0.906 false 1.646,2.542 1.49,2.24 1.49,2.24 1.406,2.24 false 2.208,2.948 2.417,3.115 2.417,3.115 2.5,3.115 false 1.552,0.219 1.833,0.417 0.281,0.198 10 false A58 2.917,0.271 3.333,0.458 0.417,0.188 10 false CANH 2.135,1.604 2.604,1.76 0.469,0.156 10 false CANL 0.438,2.698 0.76,2.875 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.135,2.156 1.375,2.333 0.24,0.177 10 false CG 2.531,3.042 2.969,3.219 0.438,0.177 10 false BAT

Disconnect the A58 headlight swivel ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A58-12 (CANH) - A58-13 (CANL) Engine switch off 54 to 69 Ω
A58-12 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
A58-13 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
A58-12 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
A58-13 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly)
*b Front view of DLC3



OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT SWIVEL ECU ASSEMBLY (CANH, CANL)

27.CONNECT CONNECTOR
a.

Reconnect the A73 No. 5 junction connector.



NEXT

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR)
28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR)
a.
U148314E01
0.056,1.611 0.254,1.767 0.198,0.156 10 *b 0.056,0.047 0.254,0.203 0.198,0.156 10 *a 0.323,2.668 0.629,2.824 0.306,0.156 10 G48 0.285,0.606 0.647,0.762 0.362,0.156 10 G102 0.572,0.099 1.017,0.255 0.445,0.156 10 CANH 2.234,1.379 2.680,1.535 0.445,0.156 10 CANL 1.102,0.176 1.225,0.176 1.225,0.176 1.37,0.597 false 2.182,1.474 2.059,1.474 2.059,1.474 1.759,0.786 false 1.087,1.99 1.338,2.145 0.251,0.156 10 CG 2.655,2.926 3.101,3.082 0.445,0.156 10 BAT 1.377,2.067 1.5,2.067 1.5,2.067 1.645,2.488 false 2.603,3.021 2.48,3.021 2.48,3.021 2.305,2.92 false

Disconnect the G102 No. 7 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G102-3 (CANH) - G102-2 (CANL) Engine switch off 108 to 132 Ω
G102-3 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G102-2 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G102-3 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G102-2 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

29.CONNECT CONNECTOR
a.

Reconnect the A73 No. 5 junction connector.



NEXT

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U149026E03
2.063,1.146 2.438,0.354 2.438,0.354 2.656,0.354 false 2.073,1.365 2.458,1.792 2.458,1.792 2.594,1.792 false 2.208,2.948 2.292,3.156 2.292,3.156 2.417,3.156 false 1.635,2.521 1.521,2.198 1.521,2.198 1.406,2.198 false 0.406,0.979 0.688,1.156 0.281,0.177 10 false R47 2.708,0.281 3.115,0.458 0.406,0.177 10 false CANH 2.625,1.719 3.01,1.896 0.385,0.177 10 false CANL 2.458,3.073 2.75,3.25 0.292,0.177 10 false BAT 1.146,2.125 1.375,2.302 0.229,0.177 10 false CG 0.406,2.688 0.688,2.865 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Disconnect the R47 No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R47-3 (CANH) - R47-14 (CANL) Engine switch off 108 to 132 Ω
R47-3 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
R47-14 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
R47-3 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
R47-14 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)
*b Front view of DLC3



OK

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)
a.
U169939E06
2.01,1.188 2.552,0.615 2.552,0.615 2.698,0.615 true 1.646,1 1.458,0.552 1.458,0.552 1.365,0.552 true 1.958,1.188 2.375,0.417 2.375,0.417 2.51,0.417 true 2.521,1.021 2.833,1.167 2.833,1.167 2.865,1.167 true 2.146,1.115 2.365,1.792 2.365,1.792 2.51,1.792 true 2.208,1.115 2.542,1.594 2.542,1.594 2.667,1.594 true 0.042,0 0.219,0.167 0.177,0.167 10 false *a 1.917,0.135 2.208,0.302 0.292,0.167 10 false G51 2.906,1.083 3.302,1.25 0.396,0.167 10 false AM22 1.031,0.479 1.375,0.646 0.344,0.167 10 false GND 2.719,0.531 3.26,0.708 0.542,0.177 10 false CA2L*A 2.531,0.333 3.146,0.51 0.615,0.177 10 false CA2H*A 2.542,1.719 3.083,1.896 0.542,0.177 10 false CA3P*B 2.698,1.51 3.313,1.688 0.615,0.177 10 false CA3N*B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 108 to 132 Ω
G51-26 (CA2H) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-25 (CA2L) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-26 (CA2H) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-25 (CA2L) - G51-1 (AM22) Engine switch off 6 kΩ or higher

except 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-11 (CA3N) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-12 (CA3P) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G51-1 (AM22) Engine switch off 6 kΩ or higher


Text in Illustration
*A for 1KD-FTV, 1GR-FE and Manual Transmission System
*B except 1KD-FTV, 1GR-FE and Manual Transmission System
*a Component with harness connected
(Power Management Control ECU)



OK

32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR LH)

NG

35.CONNECT CONNECTOR
32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR LH)
a.
U149018E04
2.188,1.156 2.458,0.365 2.458,0.365 2.677,0.365 false 2.188,1.365 2.458,1.792 2.458,1.792 2.594,1.792 false 2.208,2.948 2.292,3.156 2.292,3.156 2.417,3.156 false 1.646,2.51 1.531,2.188 1.531,2.188 1.417,2.188 false 0.406,0.99 0.677,1.167 0.271,0.177 10 false R47 2.729,0.281 3.135,0.458 0.406,0.177 10 false CANH 2.625,1.708 3.01,1.885 0.385,0.177 10 false CANL 2.448,3.073 2.74,3.25 0.292,0.177 10 false BAT 1.135,2.104 1.365,2.281 0.229,0.177 10 false CG 0.396,2.688 0.677,2.865 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R47-2 (CANH) - R47-13 (CANL) Engine switch off 200 Ω or higher
R47-2 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
R47-13 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
R47-2 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
R47-13 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 6 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 6 JUNCTION CONNECTOR

NG

33.CONNECT CONNECTOR
33.CONNECT CONNECTOR
a.

Reconnect the R47 No. 6 junction connector.



NEXT

34.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
34.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
a.
U148920E01
1.571,1.039 1.173,0.656 1.173,0.656 1.022,0.656 false 1.571,1.206 1.173,1.589 1.173,1.589 1.022,1.589 false 0.542,0.585 0.922,0.722 0.380,0.137 10 CA1P 0.531,1.512 0.920,1.649 0.389,0.137 10 CA1N 0.067,0.106 0.509,0.243 0.442,0.137 10 *a 2.632,1.041 2.906,1.178 0.275,0.137 10 R42 0.067,1.985 0.509,2.122 0.442,0.137 10 *b 0.407,2.655 0.691,2.792 0.284,0.137 10 G48 2.216,2.965 2.38,3.239 2.38,3.239 2.535,3.239 false 2.557,3.161 2.945,3.298 0.389,0.137 10 BAT 0.956,2.072 1.344,2.209 0.389,0.137 10 CG 1.638,2.521 1.429,2.147 1.429,2.147 1.274,2.147 false

Disconnect the R42 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
R42-2 (CA1P) - R42-7 (CA1N) Engine switch off 54 to 69 Ω
R42-2 (CA1P) - G48-4 (CG) Engine switch off 200 Ω or higher
R42-7 (CA1N) - G48-4 (CG) Engine switch off 200 Ω or higher
R42-2 (CA1P) - G48-16 (BAT) Engine switch off 6 kΩ or higher
R42-7 (CA1N) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BLIND SPOT MONITOR SENSOR LH (CA1P, CA1N)

35.CONNECT CONNECTOR
a.

Reconnect the R47 No. 6 junction connector.



NEXT

36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
a.
U149016E04
2.073,1.146 2.448,0.354 2.448,0.354 2.667,0.354 false 2.073,1.365 2.458,1.792 2.458,1.792 2.594,1.792 false 2.208,2.948 2.292,3.156 2.292,3.156 2.417,3.156 false 1.656,2.51 1.542,2.188 1.542,2.188 1.427,2.188 false 0.406,0.99 0.688,1.167 0.281,0.177 10 false G95 2.729,0.281 3.135,0.458 0.406,0.177 10 false CANH 2.625,1.719 3.01,1.896 0.385,0.177 10 false CANL 2.458,3.083 2.75,3.26 0.292,0.177 10 false BAT 1.156,2.094 1.385,2.271 0.229,0.177 10 false CG 0.396,2.698 0.677,2.875 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Disconnect the G95 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-3 (CANH) - G95-14 (CANL) Engine switch off 108 to 132 Ω
G95-3 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-14 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-3 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G95-14 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)
a.
U169939E06
2.01,1.188 2.552,0.615 2.552,0.615 2.698,0.615 true 1.646,1 1.458,0.552 1.458,0.552 1.365,0.552 true 1.958,1.188 2.375,0.417 2.375,0.417 2.51,0.417 true 2.521,1.021 2.833,1.167 2.833,1.167 2.865,1.167 true 2.146,1.115 2.365,1.792 2.365,1.792 2.51,1.792 true 2.208,1.115 2.542,1.594 2.542,1.594 2.667,1.594 true 0.042,0 0.219,0.167 0.177,0.167 10 false *a 1.917,0.135 2.208,0.302 0.292,0.167 10 false G51 2.906,1.083 3.302,1.25 0.396,0.167 10 false AM22 1.031,0.479 1.375,0.646 0.344,0.167 10 false GND 2.719,0.531 3.26,0.708 0.542,0.177 10 false CA2L*A 2.531,0.333 3.146,0.51 0.615,0.177 10 false CA2H*A 2.542,1.719 3.083,1.896 0.542,0.177 10 false CA3P*B 2.698,1.51 3.313,1.688 0.615,0.177 10 false CA3N*B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 108 to 132 Ω
G51-26 (CA2H) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-25 (CA2L) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-26 (CA2H) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-25 (CA2L) - G51-1 (AM22) Engine switch off 6 kΩ or higher

except 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-11 (CA3N) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-12 (CA3P) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G51-1 (AM22) Engine switch off 6 kΩ or higher


Text in Illustration
*A for 1KD-FTV, 1GR-FE and Manual Transmission System
*B except 1KD-FTV, 1GR-FE and Manual Transmission System
*a Component with harness connected
(Power Management Control ECU)



OK

38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU)

NG

53.CONNECT CONNECTOR
38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU)
NOTICE:

For vehicles without a pre-crash safety system, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Stabilizer Control ECU)".


a.
U170402E03
1.74,1.146 2.323,0.656 2.323,0.656 2.542,0.656 false 1.74,1.354 2.188,1.958 2.188,1.958 2.323,1.958 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.656,2.521 1.542,2.198 1.542,2.198 1.427,2.198 false 0.406,0.979 0.688,1.156 0.281,0.177 10 false G95 2.604,0.583 3.01,0.76 0.406,0.177 10 false CANH 2.354,1.896 2.74,2.073 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.135,2.115 1.365,2.292 0.229,0.177 10 false CG 0.396,2.698 0.677,2.875 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-6 (CANH) - G95-17 (CANL) Engine switch off 200 Ω or higher
G95-6 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-17 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-6 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G95-17 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - STABILIZER CONTROL ECU)

NG

40.CONNECT CONNECTOR
39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - STABILIZER CONTROL ECU)
NOTICE:

For vehicles without a kinetic dynamic suspension system, replace No. 3 junction connector.


a.
U149017E04
1.865,1.146 2.458,0.688 2.458,0.688 2.677,0.688 false 1.854,1.375 2.24,1.917 2.24,1.917 2.375,1.917 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.646,2.521 1.531,2.198 1.531,2.198 1.417,2.198 false 0.406,0.979 0.688,1.156 0.281,0.177 10 false G95 2.719,0.604 3.125,0.781 0.406,0.177 10 false CANH 2.417,1.833 2.802,2.01 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.135,2.115 1.365,2.292 0.229,0.177 10 false CG 0.406,2.698 0.688,2.875 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-5 (CANH) - G95-16 (CANL) Engine switch off 200 Ω or higher
G95-5 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-16 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-5 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G95-16 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

42.CONNECT CONNECTOR
40.CONNECT CONNECTOR
a.

Reconnect the G95 No. 3 junction connector.



NEXT

41.CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU)
41.CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU)
a.
U170216E03
1.635,2.521 1.479,2.219 1.479,2.219 1.396,2.219 false 2.229,2.917 2.438,3.083 2.438,3.083 2.521,3.083 false 1.906,1.271 2.063,1.042 2.063,1.042 2.146,1.042 false 1.802,1.281 1.99,0.708 1.99,0.708 2.063,0.708 false 0.646,0.885 1,1.052 0.354,0.167 10 false G118 0.458,2.688 0.781,2.865 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.135,2.146 1.375,2.323 0.24,0.177 10 false CG 2.521,2.99 2.958,3.167 0.438,0.177 10 false BAT 2.188,0.958 2.74,1.125 0.552,0.167 10 false CANH 2.104,0.625 2.625,0.792 0.521,0.167 10 false CANL

Disconnect the G118 seat belt control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G118-1 (CANH) - G118-2 (CANL) Engine switch off 54 to 69 Ω
G118-1 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G118-2 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G118-1 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G118-2 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Seat Belt Control ECU)
*b Front view of DLC3



OK

REPLACE SEAT BELT CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SEAT BELT CONTROL ECU (CANH, CANL)

42.CONNECT CONNECTOR
a.

Reconnect the G95 No. 3 junction connector.



NEXT

43.CHECK FOR SHORT IN CAN BUS WIRES (STABILIZER CONTROL ECU)
43.CHECK FOR SHORT IN CAN BUS WIRES (STABILIZER CONTROL ECU)
a.
U148725E03
1.104,1.625 1.208,1.625 1.208,1.625 1.302,1.083 false 1.458,0.333 1.354,0.333 1.354,0.333 1.229,1.042 false 1.646,2.521 1.49,2.219 1.49,2.219 1.406,2.219 false 2.229,2.917 2.438,3.083 2.438,3.083 2.521,3.083 false 0.313,0.906 0.688,1.104 0.375,0.198 10 false G123 1.49,0.26 1.906,0.448 0.417,0.188 10 false CANH 0.677,1.552 1.146,1.708 0.469,0.156 10 false CANL 0.448,2.688 0.771,2.865 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.146,2.146 1.385,2.323 0.24,0.177 10 false CG 2.521,2.99 2.958,3.167 0.438,0.177 10 false BAT

Disconnect the G123 stabilizer control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G123-29 (CANH) - G123-28 (CANL) Engine switch off 54 to 69 Ω
G123-29 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G123-28 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G123-29 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G123-28 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Stabilizer Control ECU)
*b Front view of DLC3



OK

REPLACE STABILIZER CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STABILIZER CONTROL ECU (CANH, CANL)

44.CONNECT CONNECTOR
a.

Reconnect the A73 No. 5 junction connector.



NEXT

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U149016E05
2.083,1.146 2.458,0.354 2.458,0.354 2.677,0.354 false 2.083,1.365 2.469,1.792 2.469,1.792 2.604,1.792 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.646,2.51 1.531,2.188 1.531,2.188 1.417,2.188 false 0.396,0.979 0.677,1.156 0.281,0.177 10 false G95 2.729,0.281 3.135,0.458 0.406,0.177 10 false CANH 2.646,1.708 3.031,1.885 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.156,2.104 1.385,2.281 0.229,0.177 10 false CG 0.396,2.677 0.677,2.854 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Disconnect the G95 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-3 (CANH) - G95-14 (CANL) Engine switch off 108 to 132 Ω
G95-3 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-14 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-3 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G95-14 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

46.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

46.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)
a.
U169939E06
2.01,1.188 2.552,0.615 2.552,0.615 2.698,0.615 true 1.646,1 1.458,0.552 1.458,0.552 1.365,0.552 true 1.958,1.188 2.375,0.417 2.375,0.417 2.51,0.417 true 2.521,1.021 2.833,1.167 2.833,1.167 2.865,1.167 true 2.146,1.115 2.365,1.792 2.365,1.792 2.51,1.792 true 2.208,1.115 2.542,1.594 2.542,1.594 2.667,1.594 true 0.042,0 0.219,0.167 0.177,0.167 10 false *a 1.917,0.135 2.208,0.302 0.292,0.167 10 false G51 2.906,1.083 3.302,1.25 0.396,0.167 10 false AM22 1.031,0.479 1.375,0.646 0.344,0.167 10 false GND 2.719,0.531 3.26,0.708 0.542,0.177 10 false CA2L*A 2.531,0.333 3.146,0.51 0.615,0.177 10 false CA2H*A 2.542,1.719 3.083,1.896 0.542,0.177 10 false CA3P*B 2.698,1.51 3.313,1.688 0.615,0.177 10 false CA3N*B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 108 to 132 Ω
G51-26 (CA2H) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-25 (CA2L) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-26 (CA2H) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-25 (CA2L) - G51-1 (AM22) Engine switch off 6 kΩ or higher

except 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-11 (CA3N) - G51-6 (GND) Engine switch off 200 Ω or higher
G51-12 (CA3P) - G51-1 (AM22) Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G51-1 (AM22) Engine switch off 6 kΩ or higher


Text in Illustration
*A for 1KD-FTV, 1GR-FE and Manual Transmission System
*B except 1KD-FTV, 1GR-FE and Manual Transmission System
*a Component with harness connected
(Power Management Control ECU)



OK

47.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU)

NG

53.CONNECT CONNECTOR
47.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU)
NOTICE:

For vehicles without a pre-crash safety system, go to "Check for Short in CAN Bus Wires (No. 3 Junction Connector - Stabilizer Control ECU)".


a.
U170402E04
1.74,1.156 2.323,0.667 2.323,0.667 2.542,0.667 false 1.74,1.365 2.188,1.969 2.188,1.969 2.323,1.969 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.646,2.51 1.531,2.188 1.531,2.188 1.417,2.188 false 0.406,0.979 0.688,1.156 0.281,0.177 10 false G95 2.583,0.594 2.99,0.771 0.406,0.177 10 false CANH 2.365,1.896 2.75,2.073 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.146,2.104 1.375,2.281 0.229,0.177 10 false CG 0.396,2.688 0.677,2.865 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-6 (CANH) - G95-17 (CANL) Engine switch off 200 Ω or higher
G95-6 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-17 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-6 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G95-17 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

48.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - STABILIZER CONTROL ECU)

NG

49.CONNECT CONNECTOR
48.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - STABILIZER CONTROL ECU)
NOTICE:

For vehicles without a kinetic dynamic suspension system, replace No. 3 junction connector.


a.
U149017E05
1.844,1.146 2.438,0.688 2.438,0.688 2.656,0.688 false 1.854,1.354 2.24,1.896 2.24,1.896 2.375,1.896 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.646,2.521 1.531,2.198 1.531,2.198 1.417,2.198 false 0.396,0.979 0.677,1.156 0.281,0.177 10 false G95 2.719,0.615 3.125,0.792 0.406,0.177 10 false CANH 2.417,1.823 2.802,2 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.146,2.115 1.375,2.292 0.229,0.177 10 false CG 0.396,2.688 0.677,2.865 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-5 (CANH) - G95-16 (CANL) Engine switch off 200 Ω or higher
G95-5 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-16 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G95-5 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G95-16 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

51.CONNECT CONNECTOR
49.CONNECT CONNECTOR
a.

Reconnect the G95 No. 3 junction connector.



NEXT

50.CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU)
50.CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU)
a.
U170216E04
1.646,2.542 1.49,2.24 1.49,2.24 1.406,2.24 false 2.229,2.938 2.438,3.104 2.438,3.104 2.521,3.104 false 1.906,1.281 2.063,1.052 2.063,1.052 2.146,1.052 false 1.802,1.281 1.99,0.708 1.99,0.708 2.063,0.708 false 0.625,0.885 0.979,1.052 0.354,0.167 10 false G118 0.448,2.677 0.771,2.854 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.135,2.167 1.375,2.344 0.24,0.177 10 false CG 2.563,3.031 3,3.208 0.438,0.177 10 false BAT 2.188,0.979 2.74,1.146 0.552,0.167 10 false CANH 2.104,0.635 2.625,0.802 0.521,0.167 10 false CANL

Disconnect the G118 seat belt control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G118-1 (CANH) - G118-2 (CANL) Engine switch off 54 to 69 Ω
G118-1 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G118-2 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G118-1 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G118-2 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Seat Belt Control ECU)
*b Front view of DLC3



OK

REPLACE SEAT BELT CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SEAT BELT CONTROL ECU (CANH, CANL)

51.CONNECT CONNECTOR
a.

Reconnect the G95 No. 3 junction connector.



NEXT

52.CHECK FOR SHORT IN CAN BUS WIRES (STABILIZER CONTROL ECU)
52.CHECK FOR SHORT IN CAN BUS WIRES (STABILIZER CONTROL ECU)
a.
U148725E04
1.115,1.625 1.219,1.625 1.219,1.625 1.313,1.083 false 1.458,0.344 1.354,0.344 1.354,0.344 1.229,1.052 false 1.635,2.521 1.479,2.219 1.479,2.219 1.396,2.219 false 2.229,2.917 2.438,3.083 2.438,3.083 2.521,3.083 false 0.313,0.906 0.688,1.104 0.375,0.198 10 false G123 1.49,0.271 1.906,0.458 0.417,0.188 10 false CANH 0.708,1.542 1.177,1.698 0.469,0.156 10 false CANL 0.438,2.688 0.76,2.865 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.135,2.146 1.375,2.323 0.24,0.177 10 false CG 2.521,2.99 2.958,3.167 0.438,0.177 10 false BAT

Disconnect the G123 stabilizer control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G123-29 (CANH) - G123-28 (CANL) Engine switch off 54 to 69 Ω
G123-29 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G123-28 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G123-29 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G123-28 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Stabilizer Control ECU)
*b Front view of DLC3



OK

REPLACE STABILIZER CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STABILIZER CONTROL ECU (CANH, CANL)

53.CONNECT CONNECTOR
a.

Reconnect the G95 No. 3 junction connector.



NEXT

54.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
54.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U149019E05
2.292,1.146 2.552,0.833 2.552,0.833 2.771,0.833 false 2.302,1.375 2.573,1.802 2.573,1.802 2.708,1.802 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.635,2.521 1.521,2.198 1.521,2.198 1.406,2.198 false 0.417,0.99 0.698,1.167 0.281,0.177 10 false G98 2.823,0.76 3.229,0.938 0.406,0.177 10 false CANH 2.729,1.729 3.115,1.906 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.135,2.125 1.365,2.302 0.229,0.177 10 false CG 0.396,2.688 0.677,2.865 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Disconnect the G98 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-1 (CANH) - G98-12 (CANL) Engine switch off 108 to 132 Ω
G98-1 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-12 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-1 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-12 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

55.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - PARKING ASSIST ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

55.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - PARKING ASSIST ECU)
NOTICE:

For vehicles without a side monitor system, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Driving Support ECU Assembly)".


a.
U149020E04
2.083,1.156 2.344,0.844 2.344,0.844 2.563,0.844 false 2.073,1.365 2.448,1.792 2.448,1.792 2.583,1.792 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.646,2.51 1.531,2.188 1.531,2.188 1.417,2.188 false 0.406,0.979 0.688,1.156 0.281,0.177 10 false G98 2.615,0.76 3.021,0.938 0.406,0.177 10 false CANH 2.615,1.719 3,1.896 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.135,2.115 1.365,2.292 0.229,0.177 10 false CG 0.396,2.688 0.677,2.865 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-3 (CANH) - G98-14 (CANL) Engine switch off 200 Ω or higher
G98-3 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-14 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-3 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-14 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

56.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)

NG

60.CONNECT CONNECTOR
56.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)
NOTICE:

For vehicles without a pre-crash safety system, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Clearance Warning ECU Assembly)".


a.
U170404E04
1.969,1.156 2.344,0.74 2.344,0.74 2.552,0.74 false 1.958,1.375 2.365,1.885 2.365,1.885 2.5,1.885 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.646,2.521 1.531,2.198 1.531,2.198 1.417,2.198 false 0.406,0.99 0.688,1.167 0.281,0.177 10 false G98 2.604,0.667 3.01,0.844 0.406,0.177 10 false CANH 2.542,1.802 2.927,1.979 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.135,2.115 1.365,2.292 0.229,0.177 10 false CG 0.406,2.688 0.688,2.865 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-4 (CANH) - G98-15 (CANL) Engine switch off 200 Ω or higher
G98-4 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-15 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-4 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-15 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

57.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)

NG

62.CONNECT CONNECTOR
57.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)
NOTICE:

For vehicles without a TOYOTA parking assist-sensor system, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Air Conditioning Amplifier Assembly)".


a.
U149021E05
1.844,1.156 2.365,0.698 2.365,0.698 2.573,0.698 false 1.844,1.375 2.323,1.958 2.323,1.958 2.458,1.958 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.646,2.521 1.531,2.198 1.531,2.198 1.417,2.198 false 0.396,0.979 0.677,1.156 0.281,0.177 10 false G98 2.635,0.615 3.042,0.792 0.406,0.177 10 false CANH 2.49,1.875 2.875,2.052 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.135,2.115 1.365,2.292 0.229,0.177 10 false CG 0.385,2.698 0.667,2.875 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-5 (CANH) - G98-16 (CANL) Engine switch off 200 Ω or higher
G98-5 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-16 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-5 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-16 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

58.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

64.CONNECT CONNECTOR
58.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
NOTICE:

For vehicles for 1KD-FTV, 1GR-FE and manual transmission system, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Power Management Control ECU)".


a.
U170409E02
1.74,1.156 2.365,0.698 2.365,0.698 2.573,0.698 false 1.74,1.365 2.323,1.948 2.323,1.948 2.458,1.948 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.646,2.521 1.531,2.198 1.531,2.198 1.417,2.198 false 0.396,0.99 0.677,1.167 0.281,0.177 10 false G98 2.635,0.625 3.042,0.802 0.406,0.177 10 false CANH 2.49,1.875 2.875,2.052 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.146,2.125 1.375,2.302 0.229,0.177 10 false CG 0.396,2.688 0.677,2.865 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-6 (CANH) - G98-17 (CANL) Engine switch off 200 Ω or higher
G98-6 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-17 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-6 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-17 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

59.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

NG

66.CONNECT CONNECTOR
59.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)
a.
U149022E05
2.198,1.156 2.448,0.844 2.448,0.844 2.667,0.844 false 2.188,1.365 2.438,1.792 2.438,1.792 2.573,1.792 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.646,2.531 1.531,2.208 1.531,2.208 1.417,2.208 false 0.396,0.99 0.677,1.167 0.281,0.177 10 false G98 2.708,0.76 3.115,0.938 0.406,0.177 10 false CANH 2.604,1.719 2.99,1.896 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.146,2.115 1.375,2.292 0.229,0.177 10 false CG 0.385,2.698 0.667,2.875 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-2 (CANH) - G98-13 (CANL) Engine switch off 108 to 132 Ω
G98-2 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-13 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-2 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-13 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

68.CONNECT CONNECTOR
60.CONNECT CONNECTOR
a.

Reconnect the G98 No. 1 junction connector.



NEXT

61.CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU)
61.CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU)
a.
U148726E03
0.698,1.396 0.854,1.396 0.854,1.396 0.99,1.188 false 0.979,1.656 1.167,1.656 1.167,1.656 1.063,1.177 false 1.635,2.521 1.479,2.219 1.479,2.219 1.396,2.219 false 2.229,2.917 2.438,3.083 2.438,3.083 2.521,3.083 false 0.594,1.583 1.021,1.729 0.427,0.146 10 false CANL 0.26,1.323 0.677,1.49 0.417,0.167 10 false CANH 1.719,0.25 2.052,0.469 0.333,0.219 10 false I7 0.438,2.698 0.76,2.875 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.135,2.156 1.375,2.333 0.24,0.177 10 false CG 2.521,2.99 2.958,3.167 0.438,0.177 10 false BAT

Disconnect the I7 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I7-40 (CANH) - I7-39 (CANL) Engine switch off 54 to 69 Ω
I7-40 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
I7-39 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
I7-40 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
I7-39 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Parking Assist ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO PARKING ASSIST ECU (CANH, CANL)

62.CONNECT CONNECTOR
a.

Reconnect the G98 No. 1 junction connector.



NEXT

63.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY)
63.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY)
a.
U170217E03
0.698,0.646 0.854,0.646 0.854,0.646 1.031,1.042 false 0.771,1.74 0.958,1.74 0.958,1.74 1.063,1.188 false 1.635,2.531 1.479,2.229 1.479,2.229 1.396,2.229 false 2.229,2.917 2.438,3.083 2.438,3.083 2.521,3.083 false 0.375,1.656 0.76,1.833 0.385,0.177 10 false CA2H 0.323,0.573 0.688,0.75 0.365,0.177 10 false CA2L 1.5,0.208 1.854,0.385 0.354,0.177 10 false G119 0.448,2.698 0.771,2.875 0.323,0.177 10 false G48 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.135,2.104 1.375,2.281 0.24,0.177 10 false CG 2.521,2.99 2.958,3.167 0.438,0.177 10 false BAT

Disconnect the G119 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G119-39 (CA2H) - G119-17 (CA2L) Engine switch off 54 to 69 Ω
G119-39 (CA2H) - G48-4 (CG) Engine switch off 200 Ω or higher
G119-17 (CA2L) - G48-4 (CG) Engine switch off 200 Ω or higher
G119-39 (CA2H) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G119-17 (CA2L) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Driving Support ECU Assembly)
*b Front view of DLC3



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DRIVING SUPPORT ECU ASSEMBLY (CA2H, CA2L)

64.CONNECT CONNECTOR
a.

Reconnect the G98 No. 1 junction connector.



NEXT

65.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
65.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.
U148919E02
1.185,1.047 0.88,0.749 0.88,0.749 0.729,0.749 false 0.483,0.667 0.681,0.804 0.198,0.137 10 R1 0.726,0.362 0.923,0.498 0.196,0.137 10 R2 0.064,0.068 0.506,0.205 0.442,0.137 10 *a 1.566,0.343 1.704,0.479 0.138,0.137 10 I1 1.976,0.343 2.160,0.479 0.184,0.137 10 *A 2.998,0.343 3.183,0.479 0.184,0.137 10 *B 2.447,0.343 2.814,0.479 0.367,0.137 10 G154 0.064,1.878 0.506,2.015 0.442,0.137 10 *b 0.422,2.566 0.704,2.702 0.281,0.137 10 G48 2.213,2.858 2.377,3.15 2.377,3.15 2.531,3.15 false 2.554,3.071 2.942,3.208 0.389,0.137 10 BAT 0.987,2 1.376,2.136 0.389,0.137 10 CG 1.669,2.448 1.46,2.074 1.46,2.074 1.305,2.074 false 1.408,1.047 1.119,0.447 1.119,0.447 0.969,0.447 false

Disconnect the I1*1 or G154*2 clearance warning ECU assembly connector.

*1: for 4 Sensor Type

*2: for 8 Sensor Type



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 4 Sensor Type
Tester Connection Switch Condition Specified Condition
I1-3 (R1) - I1-5 (R2) Engine switch off 54 to 69 Ω
I1-3 (R1) - G48-4 (CG) Engine switch off 200 Ω or higher
I1-5 (R2) - G48-4 (CG) Engine switch off 200 Ω or higher
I1-3 (R1) - G48-16 (BAT) Engine switch off 6 kΩ or higher
I1-5 (R2) - G48-16 (BAT) Engine switch off 6 kΩ or higher

for 8 Sensor Type
Tester Connection Switch Condition Specified Condition
G154-3 (R1) - G154-5 (R2) Engine switch off 54 to 69 Ω
G154-3 (R1) - G48-4 (CG) Engine switch off 200 Ω or higher
G154-5 (R2) - G48-4 (CG) Engine switch off 200 Ω or higher
G154-3 (R1) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G154-5 (R2) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*A for 4 Sensor Type
*B for 8 Sensor Type
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU ASSEMBLY (R1, R2)

66.CONNECT CONNECTOR
a.

Reconnect the G98 No. 1 junction connector.



NEXT

67.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
67.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U148534E05
2.302,2.813 2.51,3.052 2.51,3.052 2.563,3.052 false 1.656,2.406 1.458,2.104 1.458,2.104 1.406,2.104 false 1.833,1.146 2.052,0.281 2.052,0.281 2.188,0.281 false 1.948,1.146 2.323,0.573 2.323,0.573 2.448,0.573 false 0.104,1.906 0.302,2.073 0.198,0.167 10 false *b 0.385,2.563 0.698,2.74 0.313,0.177 10 false G48 1.146,2.021 1.375,2.198 0.229,0.177 10 false CG 2.604,2.958 2.958,3.135 0.354,0.177 10 false BAT 0.115,0.052 0.292,0.26 0.177,0.208 10 false *a 0.76,0.323 1.073,0.5 0.313,0.177 10 false G25 2.229,0.208 2.667,0.417 0.438,0.208 10 false CANH 2.5,0.51 2.938,0.719 0.438,0.208 10 false CANL

Disconnect the G25 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G25-11 (CANH) - G25-12 (CANL) Engine switch off 54 to 69 Ω
G25-11 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G25-12 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G25-11 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G25-12 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

68.CONNECT CONNECTOR
a.

Reconnect the G98 No. 1 junction connector.



NEXT

69.CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)
69.CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)
a.
U169952E03
1.104,1.563 1.177,1.563 1.177,1.563 1.563,1.24 false 1.302,1.813 1.385,1.813 1.385,1.813 1.635,1.24 false 2.302,2.896 2.51,3.125 2.51,3.125 2.563,3.125 false 1.698,2.417 1.49,2.177 1.49,2.177 1.438,2.177 false 2.458,0.802 2.385,0.802 2.385,0.802 1.875,1.083 false 2.313,0.49 2.229,0.49 2.229,0.49 1.813,1.073 false 0.094,0.042 0.292,0.25 0.198,0.208 10 false *a 0.49,0.906 0.823,1.115 0.333,0.208 10 false G51 0.063,1.969 0.26,2.135 0.198,0.167 10 false *b 0.375,2.635 0.688,2.813 0.313,0.177 10 false G48 1.135,2.073 1.365,2.25 0.229,0.177 10 false CG 2.604,3.042 2.958,3.219 0.354,0.177 10 false BAT 0.76,1.729 1.385,1.885 0.625,0.156 10 false CA2L*A 0.563,1.479 1.198,1.635 0.635,0.156 10 false CA2H*A 2.521,0.74 3.146,0.896 0.625,0.156 10 false CA3N*B 2.365,0.406 3,0.563 0.635,0.156 10 false CA3P*B

Disconnect the G51 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) Engine switch off 108 to 132 Ω
G51-26 (CA2H) - G48-4 (CG) Engine switch off 200 Ω or higher
G51-25 (CA2L) - G48-4 (CG) Engine switch off 200 Ω or higher
G51-26 (CA2H) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G51-25 (CA2L) - G48-16 (BAT) Engine switch off 6 kΩ or higher

except 1KD-FTV, 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G48-4 (CG) Engine switch off 200 Ω or higher
G51-11 (CA3N) - G48-4 (CG) Engine switch off 200 Ω or higher
G51-12 (CA3P) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*A for 1KD-FTV, 1GR-FE and Manual Transmission System
*B except 1KD-FTV, 1GR-FE and Manual Transmission System
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA2H, CA2L, CA3P, CA3N)

70.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND BODY GROUND)
a.
C348088E02
2.719,1.25 3.156,1.573 0.438,0.323 2.354,1.167 2.583,0.573 2.583,0.573 2.708,0.573 true 2.427,1.167 2.688,0.906 2.688,0.906 2.813,0.906 true 1,1.833 1.156,1.833 1.156,1.833 1.427,1.208 true 0.729,1.573 0.885,1.573 0.885,1.573 1.365,1.208 true 0.083,0.156 0.396,0.354 0.313,0.198 10 false *a 2.75,0.5 3.313,0.74 0.563,0.24 10 false AM21 2.844,0.833 3.396,1.094 0.552,0.26 10 false AM22 0.396,1.49 1.021,1.719 0.625,0.229 10 false GND 0.604,1.75 1.229,1.979 0.625,0.229 10 false GND2 2.813,1.333 3.208,1.604 0.396,0.271 10 false G51

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the G51 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G51-5 (GND2) - Body ground Always Below 1 Ω
G51-6 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G51-1 (AM22) - Body ground Always 11 to 14 V
G51-2 (AM21) - Body ground Always 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR