Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053741 INTERIOR PANELS / TRIM _0261213 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 55401E 1.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

a.

for LHD:

i.

Attach the 2 guides to install the instrument panel safety pad sub-assembly.


ii.

Install the 2 brackets with the 4 bolts and 2 nuts.


iii.

Connect the connectors and attach the clamps and claws.


iv.

Install the 2 passenger airbag bolts <G>.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


v.

Install the 6 bolts <E> and nut <F>.


vi.

Install the front floor carpet.

B361966C04
3.469,4.677 3.75,4.771 false 3.75,4.771 3.875,4.771 false 6.563,6.438 6.167,6.354 6.167,6.354 5.99,6.354 true 1,2.604 1.229,2.813 0.229,0.208 10 false *1 3.323,5.25 3.552,5.458 0.229,0.208 10 false *1 1.958,5.26 2.188,5.469 0.229,0.208 10 false *1 4.823,4.021 5.052,4.229 0.229,0.208 10 true *1 6.354,2.583 6.583,2.792 0.229,0.208 10 false *1 5.438,1.427 5.667,1.635 0.229,0.208 10 false *1 5.479,4.479 5.708,4.688 0.229,0.208 10 true *3 6.646,4.5 6.875,4.708 0.229,0.208 10 true *3 3.042,0.177 3.271,0.385 0.229,0.208 10 false *b 3.865,4.688 4.094,4.896 0.229,0.208 10 true *a 5.823,6.271 6.052,6.479 0.229,0.208 10 true *a 2.781,4.708 3.01,4.917 0.229,0.208 10 false *2
*1 Bolt <E> *2 Nut <F>
*3 Bolt <G> - -
*a Bracket *b Guide




b.

for RHD:

i.

Attach the 2 guides to install the instrument panel safety pad sub-assembly.


ii.

Install the 2 brackets with the 4 bolts and 2 nuts.


iii.

Connect the connectors and attach the clamps and claws.


iv.

Install the 2 passenger airbag bolts <G>.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


v.

Install the 6 bolts <E> and nut <F>.


vi.

Install the front floor carpet.

B361859C04
3.323,4.74 3.469,5.115 true 5.833,6.313 5.99,6.313 5.99,6.313 6.458,6.427 true 5.375,1.385 5.615,1.583 0.24,0.198 10 false *1 0.917,2.594 1.156,2.792 0.24,0.198 10 false *1 6.375,2.438 6.615,2.635 0.24,0.198 10 false *1 5.281,4.396 5.521,4.594 0.24,0.198 10 false *1 3.063,5.094 3.302,5.292 0.24,0.198 10 false *1 1.969,5.25 2.208,5.448 0.24,0.198 10 false *1 5.677,6.229 5.875,6.406 0.198,0.177 10 true *a 3.417,5.115 3.615,5.292 0.198,0.177 10 true *a 6.115,3.313 6.354,3.51 0.24,0.198 10 false *2 1.385,6.438 1.583,6.615 0.198,0.177 10 true *3 2.375,6.448 2.573,6.625 0.198,0.177 10 true *3 2.26,0.24 2.5,0.438 0.24,0.198 10 true *b
*1 Bolt <E> *2 Nut <F>
*3 Bolt <G> - -
*a Bracket *b Guide




Hide 86160P 2.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

Hide 55408F 3.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.

Attach the 2 clips, claw and 2 guides to install the No. 1 instrument panel speaker panel sub-assembly.


Hide 55409F 4.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

HINT:

Use the same procedure described for the No. 1 instrument panel speaker panel sub-assembly.


Hide 55650 5.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.

Attach the 4 clips to install the No. 1 instrument panel register assembly.


Hide 55660 6.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

HINT:

Use the same procedure described for the No. 1 instrument panel register assembly.


Hide 86160L 7.INSTALL FRONT NO. 4 SPEAKER ASSEMBLY

Hide 55421B 8.INSTALL UPPER INSTRUMENT CLUSTER FINISH PANEL

a.

Attach the 8 clips and 2 guides to install the upper instrument cluster finish panel.


Hide 55406B 9.INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Module Switch)

a.

Attach the 3 clips and guide to install the lower center instrument cluster finish panel sub-assembly.


b.

Install the 2 bolts <E>.


Hide 84970 10.INSTALL COMBINATION SWITCH ASSEMBLY (w/ Module Switch)

Hide 55522B 11.INSTALL RADIO TUNER OPENING COVER (w/o Audio)

a.

Install the radio tuner opening cover with the 4 bolts.


Hide 86120 12.INSTALL RADIO RECEIVER ASSEMBLY (w/ Radio Receiver)

Hide 86120L 13.INSTALL NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)

Hide 55420A 14.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Navigation System)

a.

Connect each connector.


b.

Attach the 10 clips to install the center instrument cluster finish panel assembly.


Hide 89533 15.INSTALL 4 WHEEL DRIVE CONTROL ECU

Hide 86741A 16.INSTALL TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)

Hide 85970A 17.INSTALL DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/ Telematics Transceiver, Double Door Lock)

Hide 55550 18.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B238219C02
2.823,2.667 3.031,2.854 0.208,0.188 10 true *1 0.469,2.656 0.677,2.844 0.208,0.188 10 false *1 2.063,1.375 2.271,1.563 0.208,0.188 10 false *2 0.698,1.365 0.948,1.542 0.25,0.177 10 true *2
*1 Bolt
*2 Screw


a.

Connect each connector.


b.

Attach the 5 clips and claw to install the glove compartment door assembly.


c.

Install the 2 bolts <C> and 2 screws <A> or <B>.


Hide 55461A 19.INSTALL INSTRUMENT PANEL ORNAMENT

a.

Attach the 5 clips to install the instrument panel ornament.


Hide 55317A 20.INSTALL INSTRUMENT SIDE PANEL RH

a.

Connect the connector.


b.

Attach the 5 clips, claw and 3 guides to install the instrument side panel RH.


Hide 83100 21.INSTALL COMBINATION METER ASSEMBLY

Hide 55404D 22.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.

except 5L-E:

i.

Connect the connector.


ii.

Attach the 4 claws, 2 clips and 2 guides to install the instrument cluster finish panel sub-assembly.



b.

for 5L-E:

i.

Connect the connector.


ii.

Attach the 4 claws, 2 clips and 2 guides to install the instrument cluster finish panel sub-assembly.



Hide 73900 23.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 55045 24.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

a.

Connect each connector and each cable.


b.

w/o Knee Airbag:

i.

Attach the 7 clips to install the lower instrument panel finish panel sub-assembly.



c.

w/ Knee Airbag:

i.

Attach the 14 clips to install the lower instrument panel finish panel sub-assembly.



d.

Install the 2 bolts <C>.


e.

Attach the 2 claws to close the cover.


Hide 55480D 25.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

a.

Connect each connector.


b.

Attach the 4 clips to install the lower instrument panel finish panel assembly.


Hide 55476C 26.INSTALL INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

a.

Connect each connector.


b.

Attach the 4 clips to install the instrument panel finish plate garnish.


Hide 55471A 27.INSTALL INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)

a.

Attach the 3 clips to install the instrument cluster finish panel ornament.


Hide 55318C 28.INSTALL INSTRUMENT SIDE PANEL LH

a.

Attach the 5 clips, claw and 3 guides to install the instrument side panel LH.


Hide 86160J 29.INSTALL FRONT NO. 3 SPEAKER ASSEMBLY

Hide 62211 31.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 74616C 33.INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH

Hide 74615E 34.INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 35.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 36.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 62111C 38.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 67920 39.INSTALL DOOR SCUFF PLATE ASSEMBLY LH

Hide 67910 40.INSTALL DOOR SCUFF PLATE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 43.INSTALL FRONT SEAT ASSEMBLY LH

Hide 44.INSTALL FRONT SEAT ASSEMBLY RH

a.

for Manual Seat:

HINT:

Use the same procedure described for the LH side.



b.

for Power Seat:

HINT:

Use the same procedure described for the LH side.




Hide 84140 45.INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY

Hide 46.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
·

Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter.

Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION