Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

If the entry lock and wireless lock operations cannot be performed, there may be door control receiver malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B492200E01
4.875,7.74 6.458,8.104 1.583,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.417,7.531 3.396,7.75 2.979,0.219 10 false Main Body ECU (Multiplex Network Body ECU) 0.708,8.031 3.688,8.25 2.979,0.219 10 false : CAN Communication Line 0.927,5.958 2.385,6.26 1.458,0.302 10 false Door Control Receiver 2.271,5.594 2.604,5.906 0.333,0.313 10 false R17 2.656,5.594 2.99,5.906 0.333,0.313 10 false R41 4.656,5.583 5.146,5.885 0.49,0.302 10 false G215 2.281,4.969 2.615,5.281 0.333,0.313 10 false R17 2.281,4.417 2.615,4.729 0.333,0.313 10 false R17 2.271,3.844 2.604,4.156 0.333,0.313 10 false R17 2.677,4.969 3.01,5.281 0.333,0.313 10 false R41 2.656,4.406 2.99,4.719 0.333,0.313 10 false R41 2.667,3.854 3,4.167 0.333,0.313 10 false R41 2.281,3.385 2.615,3.698 0.333,0.313 10 false R41 4.656,2.115 5.135,2.448 0.479,0.333 10 false G215 4.656,1.552 5.094,1.875 0.438,0.323 10 false G213 4.646,0.938 5.042,1.25 0.396,0.313 10 false G215 5.073,0.927 5.406,1.24 0.333,0.313 10 false +B 5.042,1.448 5.521,1.781 0.479,0.333 10 false IG1D 5.052,2.031 5.531,2.365 0.479,0.333 10 false ACCD 3,1.073 3.729,1.365 0.729,0.292 10 false SMART 4.656,3.854 5.135,4.188 0.479,0.333 10 false G214 4.667,4.417 5.146,4.75 0.479,0.333 10 false G214 4.656,4.979 5.135,5.313 0.479,0.333 10 false G214 5.052,3.76 5.531,4.094 0.479,0.333 10 false RCO 5.052,4.313 5.531,4.646 0.479,0.333 10 false RDAM 5.042,4.885 5.521,5.219 0.479,0.333 10 false CSEL 5.063,5.573 5.542,5.906 0.479,0.333 10 false E 5.688,1.156 6.021,1.469 0.333,0.313 10 false +B 5.656,1.729 5.99,2.042 0.333,0.313 10 false +B 5.927,1.677 6.26,1.99 0.333,0.313 10 false IC 5.698,4.104 6.031,4.417 0.333,0.313 10 false +B 5.698,4.625 6.031,4.938 0.333,0.313 10 false +B 5.698,3.51 6.031,3.823 0.333,0.313 10 false 5V 1.969,3.74 2.302,4.052 0.333,0.313 10 false +5 1.854,3.396 2.292,3.698 0.438,0.302 10 false IG*2 1.802,4.333 2.24,4.635 0.438,0.302 10 false DATA 1.813,4.885 2.292,5.219 0.479,0.333 10 false CSEL 1.844,5.594 2.323,5.927 0.479,0.333 10 false GND 1.125,4.469 1.458,4.781 0.333,0.313 10 false IC 2.354,5.406 2.688,5.719 0.333,0.313 10 false 1 2.313,5.802 2.646,6.115 0.333,0.313 10 false *1 2.719,5.802 3.052,6.115 0.333,0.313 10 false *2 2.708,5.177 3.042,5.49 0.333,0.313 10 false *2 2.333,5.177 2.667,5.49 0.333,0.313 10 false *1 2.708,4.604 3.042,4.917 0.333,0.313 10 false *2 2.313,4.604 2.646,4.917 0.333,0.313 10 false *1 2.313,4.052 2.646,4.365 0.333,0.313 10 false *1 2.729,4.052 3.063,4.365 0.333,0.313 10 false *2 2.719,5.406 3.052,5.719 0.333,0.313 10 false 12 2.76,4.792 3.094,5.104 0.333,0.313 10 false 6 2.76,4.229 3.094,4.542 0.333,0.313 10 false 2 2.76,3.667 3.094,3.979 0.333,0.313 10 false 8 2.354,3.688 2.688,4 0.333,0.313 10 false 4 2.354,4.229 2.688,4.542 0.333,0.313 10 false 5 2.354,4.792 2.688,5.104 0.333,0.313 10 false 2 2.354,3.198 2.688,3.51 0.333,0.313 10 false 1 2.917,2.99 3.823,3.292 0.906,0.302 10 false ECU-IG NO.1 0.625,2.792 2.292,3.073 1.667,0.281 10 false from IG NO.1 Relay 1.031,0.938 2.698,1.219 1.667,0.281 10 false from Battery 0.979,2.094 2.646,2.375 1.667,0.281 10 false to ACC Relay 0.75,1.542 2.417,1.823 1.667,0.281 10 false to IG NO.1 Relay 0.396,8.406 2.146,8.604 1.75,0.198 10 false *1: for 5 Pin Type 1.75,8.417 3.5,8.615 1.75,0.198 10 false *2: for 12 Pin Type 4.75,0.708 5,0.906 0.25,0.198 10 false 10 4.75,1.323 5,1.521 0.25,0.198 10 false 3 4.75,1.885 5,2.083 0.25,0.198 10 false 9 4.75,3.635 5,3.833 0.25,0.198 10 false 18 4.75,4.188 5,4.385 0.25,0.198 10 false 20 4.75,4.74 5,4.938 0.25,0.198 10 false 19 4.75,5.365 5,5.563 0.25,0.198 10 false 11

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to entry and start system (for Entry Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

Door control receiver (for 12 Pin Type):

When replacing the electrical key & TPMS receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

·

Door control receiver (for 12 Pin Type):

It is necessary to perform initialization (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the electrical key & TPMS receiver assembly if the electrical key & TPMS receiver assembly has been replaced.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

*: w/ Door Control Battery

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION



PROCEDURE

1.INSPECT BATTERY VOLTAGE
a.

Measure the voltage according to the valve(s) in the table below.

Standard voltage:

11 to 14 V


HINT:

It may be possible to tell whether the battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Check for DTCs.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK DOOR AJAR WARNING

B

3.CHECK DOOR AJAR WARNING
a.

When the doors are locked by operating the entry lock function with all doors closed, check that the door ajar warning operates.

HINT:

Warning function (door ajar warning)

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION



Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

4.CHECK POWER DOOR LOCK CONTROL SYSTEM

B

GO TO LIGHTING SYSTEM (Proceed to Door Courtesy Switch Circuit)

4.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Power door lock function operates normally A
Power door lock function does not operate normally B



A

5.CHECK KEY DIAGNOSTIC MODE

B

5.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.

i.
B485498C01
0.063,0.104 0.521,0.406 0.458,0.302 12 false *A 0.104,2.5 0.5,2.76 0.396,0.26 12 false *B 2.292,1.271 2.604,1.427 0.313,0.156 10 false *a 1.323,3.573 1.635,3.729 0.313,0.156 10 false *a
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for driver door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




ii.
B485497C01
0.104,0.208 0.479,0.51 0.375,0.302 12 false *A 0.104,2.458 0.448,2.76 0.344,0.302 12 false *B 1.344,1.458 1.656,1.615 0.313,0.156 10 false *a 2.26,3.615 2.573,3.771 0.313,0.156 10 false *a
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for front passenger door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iii.
B485492C02
0.573,1.115 2.521,0.302 true 1.906,1.146 2.531,0.302 2.531,0.302 2.719,0.302 true 2.771,0.208 3.083,0.365 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iv.
B485493C02
0.625,0.99 2.646,0.292 true 2.031,0.979 2.656,0.292 2.656,0.292 2.854,0.292 true 2.906,0.24 3.219,0.396 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




v.
B485495C02
1.99,1.25 2.615,0.188 2.615,0.188 2.802,0.188 true 1.344,1.833 2.604,0.198 true 2.854,0.115 3.167,0.271 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 3 indoor electrical key antenna assembly (inside luggage):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




vi.
B485494C02
1.823,1.313 2.135,1.469 0.313,0.156 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (outside luggage compartment):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless buzzer sounds.




Result:
Result Proceed to
Diagnostic mode inspections fail for both channels A
Diagnostic mode inspections succeed for both channels B
Diagnostic mode inspection succeeds for only one of the channels C



A

6.CHECK WAVE ENVIRONMENT

B

18.PERFORM REGISTRATION

C

27.CHECK WAVE ENVIRONMENT
6.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

7.CHECK TRANSMITTER BATTERY

B

AFFECTED BY WAVE INTERFERENCE

7.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly near the engine switch, depressing the brake pedal and pressing the engine switch.





Result:
Result Proceed to
Transmitter LED illuminates 3 times or more when switch is pressed and held A
Transmitter LED does not illuminate when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C



A

8.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

17.INSPECT TRANSMITTER BATTERY

C

8.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

9.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

10.CHECK ENTRY LOCK OPERATION
9.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK ENTRY LOCK OPERATION
10.CHECK ENTRY LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check that the entry lock and unlock functions operate.


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER AND BODY GROUND)

B

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER AND BODY GROUND)
a.

Disconnect the G214 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the R17*1 or R41*2 door control receiver connector.

·

*1: for 5 Pin Type

·

*2: for 12 Pin Type



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5 Pin Type
Tester Connection Condition Specified Condition
G214-18 (RCO) - R17-4 (+5) Always Below 1 Ω
G214-20 (RDAM) - R17-5 (DATA) Always Below 1 Ω
G214-19 (CSEL) - R17-2 (CSEL) Always Below 1 Ω
R17-1 (GND) - Body ground Always Below 1 Ω
G214-18 (RCO) or R17-4 (+5) - Body ground Always 10 kΩ or higher
G214-20 (RDAM) or R17-5 (DATA) - Body ground Always 10 kΩ or higher
G214-19 (CSEL) or R17-2 (CSEL) - Body ground Always 10 kΩ or higher

for 12 Pin Type
Tester Connection Condition Specified Condition
G214-18 (RCO) - R41-8 (+5) Always Below 1 Ω
G214-20 (RDAM) - R41-2 (DATA) Always Below 1 Ω
G214-19 (CSEL) - R41-6 (CSEL) Always Below 1 Ω
R41-12 (GND) - Body ground Always Below 1 Ω
G214-18 (RCO) or R41-8 (+5) - Body ground Always 10 kΩ or higher
G214-20 (RDAM) or R41-2 (DATA) - Body ground Always 10 kΩ or higher
G214-19 (CSEL) or R41-6 (CSEL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK ENTRY LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK ENTRY LOCK OPERATION
a.

Connect all connectors and check that the entry lock and unlock functions operate.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

13.CHECK DOOR CONTROL RECEIVER

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

13.CHECK DOOR CONTROL RECEIVER
a.
B274837C76
1.5,0.375 1.885,0.646 0.385,0.271 1.521,2.469 1.927,2.729 0.406,0.26 2.052,1.271 2.344,1.896 false 1.385,3.604 0.99,4.135 false 1.375,1.281 0.99,1.875 false 1.948,3.396 2.24,4.146 false 0.427,0.104 0.635,0.302 0.208,0.198 10 false *A 0.417,2.042 0.625,2.24 0.208,0.198 10 false *B 0.781,0.427 0.99,0.625 0.208,0.198 10 false *a 0.813,2.521 1.021,2.719 0.208,0.198 10 false *a 1.604,0.427 2.01,0.625 0.406,0.198 10 false R17 2.208,1.906 2.625,2.104 0.417,0.198 10 false GND 1.594,2.51 1.948,2.708 0.354,0.198 10 false R41 0.802,4.156 1.219,4.354 0.417,0.198 10 false GND 0.823,1.896 1.24,2.094 0.417,0.198 10 false DATA 2.094,4.156 2.51,4.354 0.417,0.198 10 false DATA
*A for 5 Pin Type
*B for 12 Pin Type
*a Component with harness connected
(Door Control Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5 Pin Type
Tester Connection Condition Specified Condition
R17-1 (GND) - Body ground Always Below 1 Ω

for 12 Pin Type
Tester Connection Condition Specified Condition
R41-12 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 5 Pin Type
Tester Connection Condition Specified Condition
R17-5 (DATA) - R17-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed

3.

All doors locked

4.

Lock or unlock switch of electrical key transmitter sub-assembly pressed


Below 1 V → Pulse generation
(See waveform 1)

for 12 Pin Type
Tester Connection Condition Specified Condition
R41-2 (DATA) - R41-12 (GND) Procedure:
1.

Engine switch off

2.

All doors closed

3.

All doors locked

4.

Lock or unlock switch of electrical key transmitter sub-assembly pressed


Below 1 V → Pulse generation
(See waveform 1)



c.
B251177C12
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 1.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content

*1: for 5 Pin Type

*2: for 12 Pin Type

Tester Connection R17-5 (DATA) - R17-1 (GND)*1
R41-2 (DATA) - R41-12 (GND)*2
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

All doors locked

4.

Lock or unlock switch of electrical key transmitter sub-assembly pressed




Result:
Result Proceed to
OK A
NG (for 5 Pin Type) B
NG (for 12 Pin Type) C



A

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B274837C77
1.5,0.375 1.885,0.646 0.385,0.271 1.521,2.469 1.927,2.729 0.406,0.26 2.052,1.271 2.719,1.865 false 1.385,3.604 0.99,4.135 false 1.563,1.281 1.177,1.875 false 1.927,3.563 2.24,4.146 false 1.896,1.281 2.24,1.865 false 1.354,3.385 0.74,3.802 false 2.115,3.385 2.677,3.917 false 0.427,0.104 0.635,0.302 0.208,0.198 10 false *A 0.417,2.042 0.625,2.24 0.208,0.198 10 false *B 0.781,0.427 0.99,0.625 0.208,0.198 10 false *a 0.813,2.521 1.021,2.719 0.208,0.198 10 false *a 1.615,0.427 2.021,0.625 0.406,0.198 10 false R17 2.615,1.885 3.031,2.083 0.417,0.198 10 false GND 1.604,2.521 1.958,2.719 0.354,0.198 10 false R41 0.802,4.156 1.219,4.354 0.417,0.198 10 false GND 1.104,1.885 1.521,2.083 0.417,0.198 10 false +5 2.208,4.146 2.625,4.344 0.417,0.198 10 false +5 2.125,1.885 2.583,2.156 0.458,0.271 10 false CSEL 0.573,3.813 0.99,4.01 0.417,0.198 10 false CSEL 2.646,3.948 3.063,4.146 0.417,0.198 10 false IG
*A for 5 Pin Type
*B for 12 Pin Type
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 5 Pin Type
Tester Connection Condition Specified Condition
R17-4 (+5) - R17-1 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly switch not pressed → pressed


Below 1 V → 4.5 to 6.0 V → Below 1 V
R17-2 (CSEL) - R17-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation

for 12 Pin Type
Tester Connection Condition Specified Condition
R41-1 (IG) - R41-12 (GND) Engine switch on (IG) 10 to 16 V
R41-8 (+5) - R41-12 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly switch not pressed → pressed


Below 1 V → 4.5 to 6.0 V → Below 1 V
R41-6 (CSEL) - R41-12 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation



Result:
Proceed to
OK
NG



OK

15.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

15.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) and perform registration again.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

16.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
16.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

17.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>INSPECTION

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

18.PERFORM REGISTRATION
a.

Perform registration of the B code.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

19.CHECK ENTRY LOCK OPERATION
19.CHECK ENTRY LOCK OPERATION
a.

After B code registration is complete, check that the entry lock and unlock functions operate.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

20.READ VALUE USING GTS (B CODE)

B

END (B CODE REGISTRATION FAILED)

20.READ VALUE USING GTS (B CODE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
B Code B code registration status Regd or No Regd Regd: B code registered correctly
No Regd: B code not registered correctly
-


Result:
Result Proceed to
"No Regd" is displayed on the GTS A
"Regd" is displayed on the GTS B



A

21.READ VALUE USING GTS (B CODE DIFFERENCE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

21.READ VALUE USING GTS (B CODE DIFFERENCE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
B Code Difference B code mismatch Yes or No Yes: Communication malfunction
No: Communication normal
-


Result:
Result Proceed to
"No" is displayed on the GTS A
"Yes" is displayed on the GTS B



A

22.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

22.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage while checking the Data List on the GTS.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

Read the Data List according to the display on the GTS.

B344851C45
1.677,0.333 2.135,0.573 0.458,0.24 5.125,0.333 5.552,0.573 0.427,0.24 3.323,0.333 3.698,0.573 0.375,0.24 1.031,2.063 1.365,1.219 false 4.667,1.25 4.792,2.156 false 0.844,2.125 1.25,2.313 0.406,0.188 10 false IG1D 1.708,0.385 2.115,0.573 0.406,0.188 10 false G213 4.635,2.198 5.042,2.385 0.406,0.188 10 false ACCD 5.167,0.375 5.573,0.563 0.406,0.188 10 false G215 0.188,0.125 0.594,0.313 0.406,0.188 10 false *a 3.354,0.385 3.76,0.573 0.406,0.188 10 false G214
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Power Source Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG ON: Engine switch on (IG)
ST ON: Sending engine start request signal
-

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G213-3 (IG1D) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) Below 1 V
Engine switch on (IG) 9 V or higher
G215-9 (ACCD) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) 8.5 V or higher
Engine switch on (IG) 8.5 V or higher




Result:
Proceed to
OK
NG



OK

23.READ VALUE USING GTS (ACC SW, IG SW)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

23.READ VALUE USING GTS (ACC SW, IG SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Engine switch status ON or OFF ON: Engine switch on (ACC)
OFF: Engine switch off
"ON" is displayed even though the engine switch is on (IG).
IG SW Engine switch status ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
"OFF" is displayed even though the engine switch is on (ACC).

HINT:

If the certification ECU (smart key ECU assembly) misjudges for any reason that the engine switch is on (IG) even though the engine switch is off, the entry lock and unlock functions stop.



Result:
Result Proceed to
The main body ECU (multiplex network body ECU) judges properly that the power source is off when the engine switch is off A
The main body ECU (multiplex network body ECU) does not judge properly that the power source is off when the engine switch is off B



A

24.CHECK ENTRY LOCK OPERATION

B

24.CHECK ENTRY LOCK OPERATION
a.

Disconnect and reconnect the certification ECU (smart key ECU assembly) connector.



Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

25.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

25.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration again.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

26.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
26.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

27.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck key diagnostic mode.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

28.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

AFFECTED BY WAVE INTERFERENCE

28.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

29.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

30.CHECK WAVE ENVIRONMENT
29.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

30.CHECK WAVE ENVIRONMENT
30.CHECK WAVE ENVIRONMENT
a.

Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck key diagnostic mode.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

31.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)

B

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

31.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
a.

Disconnect the G214 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the R17*1 or R41*2 door control receiver connector.

·

*1: for 5 Pin Type

·

*2: for 12 Pin Type



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5 Pin Type
Tester Connection Condition Specified Condition
G214-19 (CSEL) - R17-2 (CSEL) Always Below 1 Ω
G214-19 (CSEL) or R17-2 (CSEL) - Body ground Always 10 kΩ or higher

for 12 Pin Type
Tester Connection Condition Specified Condition
G214-19 (CSEL) - R41-6 (CSEL) Always Below 1 Ω
G214-19 (CSEL) or R41-6 (CSEL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

32.CHECK ENTRY LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.CHECK ENTRY LOCK OPERATION
a.

Connect all connectors and check that the entry lock and unlock functions operate.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

33.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

33.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B274837C78
1.5,0.375 1.885,0.646 0.385,0.271 1.521,2.469 1.927,2.729 0.406,0.26 2.052,1.271 2.344,1.896 false 1.385,3.604 0.99,4.135 false 1.844,1.281 1.344,1.906 false 0.76,3.833 1.365,3.396 false 0.427,0.104 0.635,0.302 0.208,0.198 10 false *A 0.417,2.042 0.625,2.24 0.208,0.198 10 false *B 0.781,0.427 0.99,0.625 0.208,0.198 10 false *a 0.813,2.521 1.021,2.719 0.208,0.198 10 false *a 1.573,0.427 1.979,0.625 0.406,0.198 10 false R17 2.208,1.906 2.625,2.104 0.417,0.198 10 false GND 1.625,2.521 1.979,2.719 0.354,0.198 10 false R41 0.802,4.156 1.219,4.354 0.417,0.198 10 false GND 1.198,1.917 1.615,2.115 0.417,0.198 10 false CSEL 0.573,3.854 0.99,4.052 0.417,0.198 10 false CSEL
*A for 5 Pin Type
*B for 12 Pin Type
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 5 Pin Type
Tester Connection Condition Specified Condition
R17-2 (CSEL) - R17-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation

for 12 Pin Type
Tester Connection Condition Specified Condition
R41-6 (CSEL) - R41-12 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation



Result:
Proceed to
OK
NG



OK

34.CHECK DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

34.CHECK DOOR CONTROL RECEIVER
a.

Enter key diagnostic mode and select the channel for which the wireless buzzer did not sound.


b.
B274837C79
1.5,0.375 1.885,0.646 0.385,0.271 1.521,2.469 1.927,2.729 0.406,0.26 2.052,1.271 2.344,1.896 false 1.385,3.604 0.99,4.135 false 1.375,1.281 0.99,1.875 false 1.917,3.375 2.24,4.135 false 0.427,0.104 0.635,0.302 0.208,0.198 10 false *A 0.417,2.042 0.625,2.24 0.208,0.198 10 false *B 0.781,0.427 0.99,0.625 0.208,0.198 10 false *a 0.813,2.521 1.021,2.719 0.208,0.198 10 false *a 1.573,0.427 1.979,0.625 0.406,0.198 10 false R17 2.208,1.906 2.625,2.104 0.417,0.198 10 false GND 1.594,2.51 1.948,2.708 0.354,0.198 10 false R41 0.802,4.156 1.219,4.354 0.417,0.198 10 false GND 0.823,1.896 1.24,2.094 0.417,0.198 10 false DATA 2.094,4.156 2.51,4.354 0.417,0.198 10 false DATA
*A for 5 Pin Type
*B for 12 Pin Type
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 5 Pin Type
Tester Connection Condition Specified Condition
R17-5 (DATA) - R17-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed

3.

All doors locked

4.

Lock or unlock switch of electrical key transmitter sub-assembly pressed


Below 1 V → Pulse generation
(See waveform 1)

for 12 Pin Type
Tester Connection Condition Specified Condition
R41-2 (DATA) - R41-12 (GND) Procedure:
1.

Engine switch off

2.

All doors closed

3.

All doors locked

4.

Lock or unlock switch of electrical key transmitter sub-assembly pressed


Below 1 V → Pulse generation
(See waveform 1)


HINT:

Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).



c.
B251177C12
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 1.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content

*1: for 5 Pin Type

*2: for 12 Pin Type

Tester Connection R17-5 (DATA) - R17-1 (GND)*1
R41-2 (DATA) - R41-12 (GND)*2
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

All doors locked

4.

Lock or unlock switch of electrical key transmitter sub-assembly pressed




Result:
Result Proceed to
OK A
NG (for 5 Pin Type) B
NG (for 12 Pin Type) C



A

35.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

35.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) and perform registration again.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

36.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
36.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)