Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM J

1GD-FTV ENGINE CONTROL  ECD SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, the starter signal is also sent to terminal STA of the ECM.

The starter signal mainly performs engine control when the engine is started.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

This chart is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>PROBLEM SYMPTOMS TABLE).


PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B


A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

17.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch to on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the GTS when the engine switch is turned to the on (IG) and START positions.

OK:
Condition GTS Display (Starter Signal)
Engine switch on (IG) OFF
Engine started ON



Result
Result Proceed to
OK A
NG (for automatic transmission models) B
NG (for manual transmission models) C


A

3.INSPECT STARTER RELAY (ST)

B

11.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

14.INSPECT CLUTCH START SWITCH ASSEMBLY
3.INSPECT STARTER RELAY (ST)
a.


OK

4.INSPECT STARTER ASSEMBLY

NG

REPLACE STARTER RELAY (ST)

4.INSPECT STARTER ASSEMBLY

Result
Result Proceed to
OK A
NG (for 2.0 kW type) B
NG (for 2.7 kW type) C


A

5.CHECK HARNESS AND CONNECTOR (STARTER RELAY - STARTER ASSEMBLY)

B

C

5.CHECK HARNESS AND CONNECTOR (STARTER RELAY - STARTER ASSEMBLY)
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 2.0 kW type):
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 3 - D11-1 Always Below 1 Ω
Starter relay (ST) terminal 3 or D11-1 - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance (for 2.7 kW type):
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 3 - D10-1 Always Below 1 Ω
Starter relay (ST) terminal 3 or D10-1 - Body ground and other terminals Always 10 kΩ or higher



d.

Reinstall the starter relay.


e.

Reconnect the starter assembly connector.



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER ASSEMBLY)
a.

Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (for 2.0 kW type):
Tester Connection Condition Specified Condition
D8-1 - Body ground Always 11 to 14 V


Standard Voltage (for 2.7 kW type):
Tester Connection Condition Specified Condition
D9-1 - Body ground Always 11 to 14 V



c.

Reconnect the starter assembly connector.



OK

7.CHECK HARNESS AND CONNECTOR (STARTER RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (STARTER RELAY - BODY GROUND)
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 1 - Body ground Always Below 1 Ω


Result
Result Proceed to
OK (for automatic transmission models) A
OK (for manual transmission models) B
NG C


c.

Reinstall the starter relay (ST).



A

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CERTIFICATION ECU - STATER RELAY (ST))

B

9.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - CERTIFICATION ECU - STATER RELAY (ST))

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CERTIFICATION ECU - STATER RELAY (ST))
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the certification ECU (Smart Key ECU Assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C159-5 (L) - Starter relay (ST) terminal 2 Always Below 1 Ω
G213-12 (STA) - Starter relay (ST) terminal 2 Always Below 1 Ω
C159-5 (L) or Starter relay (ST) terminal 2 - Body ground and other terminals Always 10 kΩ or higher
G213-12 (STA) or Starter relay (ST) terminal 2 - Body ground and other terminals Always 10 kΩ or higher



e.

Reinstall the starter relay (ST).


f.

Reconnect the park/neutral position switch assembly connector.


g.

Reconnect the certification ECU (Smart Key ECU Assembly) connector.



OK

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER RELAY (ST))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - CERTIFICATION ECU - STATER RELAY (ST))
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the certification ECU (Smart Key ECU Assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
A40-1 - Starter relay (ST) terminal 2 Always Below 1 Ω
G213-12 (STA) - Starter relay (ST) terminal 2 Always Below 1 Ω
A40-1 or Starter relay (ST) terminal 2 - Body ground and other terminals Always 10 kΩ or higher
G213-12 (STA) or Starter relay (ST) terminal 2 - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
r1-1 - Starter relay (ST) terminal 2 Always Below 1 Ω
G213-12 (STA) - Starter relay (ST) terminal 2 Always Below 1 Ω
r1-1 or Starter relay (ST) terminal 2 - Body ground and other terminals Always 10 kΩ or higher
G213-12 (STA) or Starter relay (ST) terminal 2 - Body ground and other terminals Always 10 kΩ or higher



e.

Reinstall the starter relay.


f.

Reconnect the the clutch start switch assembly connector.


g.

Reconnect the certification ECU (Smart Key ECU Assembly) connector.



OK

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER RELAY (ST))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER RELAY (ST))
a.
A413699E01
0.323,0.302 0.635,0.5 0.313,0.198 10 false *1 2.792,1.406 3.104,1.604 0.313,0.198 10 false *2

Remove the starter relay (ST) from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 Starter Relay (ST)


c.

Reinstall the starter relay (ST).



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER RELAY)

11.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

12.CHECK HARNESS AND CONNECTOR (ECM - CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - STATER RELAY (ST))

NG

12.CHECK HARNESS AND CONNECTOR (ECM - CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - STATER RELAY (ST))
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the certification ECU (Smart Key ECU Assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C159-5 (L) - Starter relay (ST) terminal 2 Always Below 1 Ω
G213-12 (STA) - Starter relay (ST) terminal 2 Always Below 1 Ω
C159-5 (L) or Starter relay (ST) terminal 2 - Body ground and other terminals Always 10 kΩ or higher
G213-12 (STA) or Starter relay (ST) terminal 2 - Body ground and other terminals Always 10 kΩ or higher



e.

Reinstall the starter relay.


f.

Reconnect the park/neutral position switch assembly connector.


g.

Reconnect the certification ECU (Smart Key ECU Assembly) connector.



OK

13.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CERTIFICATION ECU - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CERTIFICATION ECU - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the certification ECU (Smart Key ECU Assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C159-4 (B) - G213-10 (STAR) Always Below 1 Ω
G213-10 (STAR) - G184-11 (NSW) Always Below 1 Ω
C159-4 (B) or G213-10 (STAR) - Body ground and other terminals Always 10 kΩ or higher
G213-10 (STAR) or G184-11 (NSW) - Body ground and other terminals Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reconnect the park/neutral position switch assembly connector.


g.

Reconnect the certification ECU (Smart Key ECU Assembly) connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).



OK

15.CHECK HARNESS AND CONNECTOR (ECM - CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - STATER RELAY (ST))

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (ECM - CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - STATER RELAY (ST))
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the certification ECU (Smart Key ECU Assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
C40-1 - Starter relay (ST) terminal 2 Always Below 1 Ω
G213-12 (STA) - Starter relay (ST) terminal 2 Always Below 1 Ω
C40-1 or Starter relay (ST) terminal 2 - Body ground and other terminals Always 10 kΩ or higher
G213-12 (STA) or Starter relay (ST) terminal 2 - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
r1-1 - Starter relay (ST) terminal 2 Always Below 1 Ω
G213-12 (STA) - Starter relay (ST) terminal 2 Always Below 1 Ω
r1-1 or Starter relay (ST) terminal 2 - Body ground and other terminals Always 10 kΩ or higher
G213-12 (STA) or Starter relay (ST) terminal 2 - Body ground and other terminals Always 10 kΩ or higher



e.

Reinstall the starter relay.


f.

Reconnect the clutch start switch assembly connector.


g.

Reconnect the certification ECU (Smart Key ECU Assembly) connector.



OK

16.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - CERTIFICATION ECU - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - CERTIFICATION ECU - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the certification ECU (Smart Key ECU Assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
A40-2 - G213-10 (STAR) Always Below 1 Ω
A40-2 or G213-10 (STAR) - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
r1-2 - G213-10 (STAR) Always Below 1 Ω
r1-2 or G213-10 (STAR) - Body ground and other terminals Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reconnect the clutch start switch assembly connector.


g.

Reconnect the certification ECU (Smart Key ECU Assembly) connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch to on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the GTS when the engine switch is turned to the on (IG) and START positions.

OK:
Condition GTS Display (Starter Signal)
Engine switch on (IG) OFF
Engine started ON




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY - ECM)