Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2017.08–2020.08
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261239 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, forward recognition camera system, lane departure alert system, road sign assist system or pre-crash safety system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 75547B 1.INSTALL NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedures if replacing any No. 3 windshield outside moulding clips.


a.

Install a nose piece to an air riveter or hand riveter.


b.

Insert the mandrel part of a new No. 3 windshield outside moulding clip into the nose piece.


c.
B238989

Using the riveter, install the No. 3 windshield outside moulding clips shown in the illustration.

HINT:

If the clip cannot be cut, pull it once and cut it.


NOTICE:
B171664C39
1.24,1.104 1.094,1.635 1.094,1.635 1.25,2.198 false 1.083,1.635 0.813,1.635 false 1.76,0.906 2.021,1.625 2.021,1.625 1.76,2.5 false 2.021,1.625 2.302,1.625 false 2.271,0.542 2.469,0.74 0.198,0.198 10 false *a 2.271,2.385 2.49,2.583 0.219,0.198 10 false *b 0.625,1.563 0.813,1.76 0.188,0.198 10 false *1 2.333,1.542 2.521,1.719 0.188,0.177 10 false *2
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT


Do not pry the clip with the riveter as this will cause damage to the riveter and mandrel.


NOTICE:
B172390C37
0.719,0.115 1.021,0.115 false 0.813,1.135 1.01,1.135 false 0.813,2.417 1.01,2.417 false 2.323,0.531 2.51,0.708 0.188,0.177 10 false *a 2.323,1.531 2.5,1.708 0.177,0.177 10 false *a 2.354,2.74 2.552,2.917 0.198,0.177 10 false *b 1.052,2.333 1.229,2.49 0.177,0.156 10 false *1 1.063,1.052 1.24,1.208 0.177,0.156 10 false *1 1.063,0.031 1.24,0.188 0.177,0.156 10 false *1
*1 Riveter
*a INCORRECT
*b CORRECT


·

Confirm that the clips are seated properly against the moulding.

·

Do not tilt the riveter when installing the clip to the moulding.

·

Do not leave any space between the clip head and moulding.



NOTICE:
B172391C36
0.74,0.656 0.938,0.656 false 0.74,2.125 0.948,2.125 false 2.302,1 2.5,1.177 0.198,0.177 10 false *a 2.344,2.469 2.552,2.646 0.208,0.177 10 false *b 0.99,0.563 1.188,0.729 0.198,0.167 10 false *1 0.99,2.031 1.198,2.198 0.208,0.167 10 false *1
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the moulding and body. Firmly hold together the 2 items while installing the clip.



Hide 75545B 2.INSTALL NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

a.

Install the 5 No. 1 windshield moulding clips.

HINT:

Use the same procedure to install the 5 No. 1 windshield moulding clips on the other side.



Hide 56115A 3.INSTALL NO. 1 WINDSHIELD GLASS STOPPER

B238996C04
1.656,0.604 1.438,0.604 false 2.604,0.583 2.823,0.583 false 1.302,0.5 1.583,0.708 0.281,0.208 10 false *1 2.865,0.5 3.115,0.729 0.25,0.229 10 false *a
*1 No. 1 Windshield Glass Stopper
*a Vehicle Body


a.

Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.


Hide 56116C 4.INSTALL NO. 2 WINDSHIELD GLASS STOPPER

a.

Apply glass primer to the windshield glass where the No. 2 windshield glass stoppers will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Install 2 new No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.

B238997C02
0.521,1.156 0.604,0.719 0.604,0.719 0.865,0.719 true 1.448,1.417 1.563,0.667 1.563,0.667 1.823,0.667 true 1.208,0.938 1.208,1.844 false 5.917,0.865 5.917,1.771 false 5.208,1.167 5.292,0.729 5.292,0.729 5.552,0.729 true 6.135,1.427 6.25,0.677 6.25,0.677 6.521,0.677 true 0.385,1.417 0.458,1.958 false 5.052,1.427 5.135,1.969 false 2.052,1.719 2.156,1.906 0.104,0.188 10 false a 0.031,0 0.219,0.208 0.188,0.208 10 false *a 0.417,1.969 0.604,2.177 0.188,0.208 10 false *c 1.125,1.875 1.313,2.083 0.188,0.208 10 false *d 1.865,0.594 2.052,0.802 0.188,0.208 10 false *b 0.875,0.646 1.063,0.854 0.188,0.208 10 false *1 6.698,1.74 6.802,1.927 0.104,0.188 10 false a 5.823,1.823 6.01,2.031 0.188,0.208 10 false *d 6.552,0.604 6.74,0.813 0.188,0.208 10 false *b 5.573,0.656 5.76,0.865 0.188,0.208 10 false *1 5.083,1.99 5.271,2.198 0.188,0.208 10 false *c
*1 Windshield Glass - -
*a Backside *b Ceramic Notch
*c Ceramic Line *d Center


Standard:
Area Specified Condition
a 14.1 mm (0.555 in.)



Hide 75533G 5.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Using a brush or sponge, coat the contact surface of the windshield glass and windshield outside moulding with glass primer as shown in the illustration.

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Do not coat the adhesive with glass primer.

·

Throw away any leftover primer.



B238998C04
0.052,0 0.354,0.302 0.302,0.302 10 false *a 3.531,0.479 3.719,0.677 0.188,0.198 10 false A 3.552,0.938 3.729,1.146 0.177,0.208 10 false A 5.552,0.583 6.177,0.865 0.625,0.281 10 false A - A 6.688,1.448 6.927,1.667 0.24,0.219 10 false a
*a Backside - -


Standard:
Area Specified Condition
a 6.9 mm (0.271 in.)



b.

Remove the peeling paper from a new windshield outside moulding and install the windshield outside moulding as shown in the illustration.


Hide 56117D 6.INSTALL WINDSHIELD GLASS ADHESIVE DAM

a.

Apply glass primer to the windshield glass where the new windshield glass adhesive dam will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from the adhesive part of the windshield glass adhesive dam. Install the windshield glass adhesive dam (adhesive side) to the windshield glass (glass primer area), but exclude the area above the notches on the upper part of the windshield glass.

U115595C01
2.958,5.177 2.75,5.531 false 4.583,3.969 4.354,4.313 false 6.01,2.24 6.281,2.438 false 6.083,2.729 6.177,2.865 false 4.833,4 5.031,4.354 false 3.24,5.208 3.438,5.552 false 5.646,2.979 5.771,3.146 5.771,3.146 5.792,2.927 false 1.469,2.958 1.344,3.125 1.344,3.125 1.323,2.906 false 1.083,2.26 0.813,2.458 false 1.021,2.698 0.927,2.844 false 0.021,0.01 0.24,0.24 0.219,0.229 10 false *a 2.135,2.135 2.302,2.354 0.167,0.219 10 false A 2.479,2.188 2.646,2.406 0.167,0.219 10 false A 3.74,2.427 3.938,2.646 0.198,0.219 10 false B 3.76,2.781 3.958,3 0.198,0.219 10 false B 4.396,1.698 4.615,1.917 0.219,0.219 10 false A 4.719,1.635 4.938,1.854 0.219,0.219 10 false A 1.135,0.604 1.333,0.802 0.198,0.198 10 false *b 5.823,0.615 5.979,0.792 0.156,0.177 10 false *b 4.26,4.313 4.479,4.49 0.219,0.177 10 false *c 5.042,4.354 5.26,4.531 0.219,0.177 10 false *d 2.625,5.542 2.844,5.719 0.219,0.177 10 false *c 4.75,3.219 4.927,3.396 0.177,0.177 10 false a 3.927,4.448 4.115,4.677 0.188,0.229 10 false a 2.125,3.49 2.49,3.656 0.365,0.167 10 false A - A 2.125,4.594 2.49,4.76 0.365,0.167 10 false B - B 1.229,3.135 1.448,3.313 0.219,0.177 10 false *b 5.854,2.146 6.073,2.323 0.219,0.177 10 false *c 6.146,2.885 6.365,3.063 0.219,0.177 10 false *d 5.74,3.167 5.958,3.344 0.219,0.177 10 false *b 3.396,5.573 3.615,5.75 0.219,0.177 10 false *d 1.083,2.135 1.302,2.313 0.219,0.177 10 false *c 0.802,2.844 1.021,3.021 0.219,0.177 10 false *d
*a Backside *b Ceramic Notch
*c Dam Center Line *d Adhesive Center Line


Standard:
Area Specified Condition
a 6.5 mm (0.256 in.)



Hide 56111 7.INSTALL WINDSHIELD GLASS

B238990C02
1.625,0.99 1.396,0.99 1.396,0.99 1.396,1.865 true 1.323,1.885 1.583,2.115 0.26,0.229 10 false *a
*a Matchmarks


a.

Position the windshield glass.

i.

Using suction cups, place the windshield glass in the correct position.


ii.

Check that the entire contact surface of the windshield glass rim is perfectly even.


iii.

Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.

HINT:
·

Placing matchmarks is only necessary when installing new windshield glass. When reusing the windshield glass, matchmarks should already be present.

·

When reusing the windshield glass, check and correct the matchmark positions.



NOTICE:

Check that the stoppers are attached to the vehicle body correctly.



iv.

Using suction cups, remove the windshield glass.



b.
B495713C01
2.406,1.156 1.938,0.958 false 2.396,2.156 1.885,1.938 false 2.313,2.313 1.604,2.365 false 0.573,3.125 0.333,3.229 false 1.75,0.875 2.063,1.031 0.313,0.156 10 false *d 1.396,2.313 1.708,2.469 0.313,0.156 10 false *c 1.99,0.281 2.302,0.438 0.313,0.156 10 false *a 2.042,2.51 2.354,2.667 0.313,0.156 10 false *b 1.698,1.813 2.01,2.01 0.313,0.198 10 false *d 0.167,3.156 0.479,3.354 0.313,0.198 10 false *d
*a CORRECT
*b INCORRECT
*c Adhesive
*d Body Primer


Using a brush, apply body primer to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.




c.

Using a brush or sponge, apply glass primer to the contact surface of the windshield glass.

B495714C01
4.885,0.875 4.583,1.177 false 6.427,0.885 6.115,1.219 false 5.667,1.958 5.99,2.271 false 5.094,3.125 4.76,3.531 4.76,3.531 5.292,3.146 false 1.708,2.813 1.917,3.25 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 3.99,0.156 4.76,0.354 0.771,0.198 10 false B - B 5.625,0.146 6.396,0.344 0.771,0.198 10 false A - A 4.635,1.427 5.406,1.625 0.771,0.198 10 false C - C 4.354,2.448 5.125,2.646 0.771,0.198 10 false D - D 4.969,0.302 5.125,0.5 0.156,0.198 10 false a 6.531,0.302 6.688,0.5 0.156,0.198 10 false a 4.417,1.167 4.729,1.365 0.313,0.198 10 false *b 5.958,1.188 6.271,1.385 0.313,0.198 10 false *b 5.99,2.313 6.302,2.51 0.313,0.198 10 false *b 4.615,3.51 4.927,3.708 0.313,0.198 10 false *b 5.344,3.531 5.5,3.729 0.156,0.198 10 false d 5.677,1.406 5.833,1.604 0.156,0.198 10 false b 5.146,2.531 5.302,2.729 0.156,0.198 10 false c 0.813,0.906 0.969,1.104 0.156,0.198 10 false A 0.823,1.25 0.979,1.448 0.156,0.198 10 false A 1.667,0.917 1.823,1.115 0.156,0.198 10 false B 1.646,1.26 1.802,1.458 0.156,0.198 10 false B 2.396,0.917 2.552,1.115 0.156,0.198 10 false A 2.427,1.26 2.583,1.458 0.156,0.198 10 true A 0.104,1.948 0.26,2.146 0.156,0.198 10 false C 0.448,2.052 0.604,2.25 0.156,0.198 10 false C 3.323,1.479 3.479,1.677 0.156,0.198 10 false C 3.667,1.417 3.823,1.615 0.156,0.198 10 false C 3.219,2.479 3.375,2.677 0.156,0.198 10 false D 3.271,2.917 3.479,3.146 0.208,0.229 10 false D 1.896,3.323 2.208,3.521 0.313,0.198 10 false *b
*a Backside *b Adhesive Center Line
V100155

Glass Primer - -


Standard:
Area Specified Condition
a 9.5 mm (0.374 in.)
b 3.0 mm (0.118 in.)
c 8.0 mm (0.315 in.)
d 7.0 mm (0.276 in.)


HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




d.

Apply adhesive to the windshield glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of a cartridge nozzle as shown in the illustration.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the windshield glass as shown in the illustration.

B239002C04
5.698,2.104 5.99,2.396 false 6.448,1.031 6.74,1.323 false 4.906,1.031 5.188,1.323 false 5.073,3.271 5.583,3.563 5.583,3.563 5.302,3.271 false 0.042,0 0.406,0.271 0.365,0.271 10 false *a 1.646,0.146 1.854,0.375 0.208,0.229 10 false A 1.615,0.469 1.823,0.698 0.208,0.229 10 false A 0.76,0.146 0.948,0.344 0.188,0.198 10 true B 0.75,0.51 0.938,0.708 0.188,0.198 10 false B 2.406,0.156 2.594,0.354 0.188,0.198 10 false B 2.396,0.5 2.583,0.698 0.188,0.198 10 true B 0.135,1.198 0.313,1.406 0.177,0.208 10 false C 0.448,1.281 0.625,1.49 0.177,0.208 10 false C 3.323,0.698 3.542,0.917 0.219,0.219 10 false C 3.646,0.625 3.865,0.844 0.219,0.219 10 false C 3.229,1.719 3.448,1.906 0.219,0.188 10 false D 3.25,2.125 3.469,2.313 0.219,0.188 10 false D 0.135,3.01 0.375,3.219 0.24,0.208 10 false a 0.479,2.49 0.646,2.688 0.167,0.198 10 false b 2.844,3.073 3.021,3.25 0.177,0.177 10 false a 3.333,3.198 3.49,3.344 0.156,0.146 10 false b 4.99,0.219 5.313,0.51 0.323,0.292 10 false c 6.521,0.208 6.823,0.49 0.302,0.281 10 false c 5.698,1.25 5.938,1.479 0.24,0.229 10 false d 5.167,2.469 5.385,2.698 0.219,0.229 10 false b 6,2.385 6.25,2.615 0.25,0.229 10 false *b 4.125,0.094 4.583,0.375 0.458,0.281 10 false A - A 5.708,0.115 6.094,0.281 0.385,0.167 10 false B - B 4.75,1.458 5.25,1.688 0.5,0.229 10 false C - C 4.448,2.406 4.885,2.615 0.438,0.208 10 false D - D 5.198,1.24 5.448,1.469 0.25,0.229 10 false *b 6.802,1.271 7.052,1.5 0.25,0.229 10 false *b 5.625,3.542 5.875,3.771 0.25,0.229 10 false *b
*a Backside *b Adhesive Center Line
V100155C24
0,0 0,0 false

Adhesive - -


Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 9.5 mm (0.374 in.)
d 3.0 mm (0.118 in.)




e.
B238991C01
0.427,0.571 0.255,0.408 false 0.057,0.266 0.293,0.516 0.236,0.250 10 *a
*a Matchmarks


Install the windshield glass to the vehicle body.

i.

Using suction cups, position the windshield glass so that the matchmarks are aligned. Press it in gently along the rim.


ii.

Lightly press the outer surface of the windshield glass to ensure that it is securely installed to the vehicle body.

NOTICE:
·

Check that the stoppers are attached to the vehicle body correctly.

·

Check that the vehicle body and windshield glass have a small gap between them.




iii.

Hold the windshield glass in place securely with protective tape or equivalent until the adhesive hardens.

NOTICE:

Do not drive the vehicle within the time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




f.

w/ Windshield Deicer System:

Connect the windshield deicer connector.


Hide 56111 8.CHECK FOR LEAK AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 63310 9.INSTALL ROOF HEADLINING ASSEMBLY

a.

for 5 Door:

i.

Return the roof headlining to its original position. Refer to the following procedures.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 5 Door)>INSTALLATION



b.

for 3 Door:

i.

Return the roof headlining to its original position. Refer to the following procedures.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 3 Door)>INSTALLATION



Hide 87810 10.INSTALL INNER REAR VIEW MIRROR ASSEMBLY

Hide 89941 11.INSTALL RAIN SENSOR (w/ Rain Sensor)

Hide 86401 12.INSTALL FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY (w/ Lane Departure Alert System)

Hide 8646C 13.INSTALL FORWARD RECOGNITION CAMERA (w/ Lane Departure Alert System)

Hide 86464A 14.INSTALL FORWARD RECOGNITION LATCH (w/ Lane Departure Alert System)

Hide 86466D 15.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Lane Departure Alert System)

Hide 86466E 16.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Lane Departure Alert System)

Hide 81260A 17.INSTALL MAP LIGHT ASSEMBLY

Hide 74616C 26.INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH

Hide 74615E 27.INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH

Hide 62312B 28.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 29.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 62111C 31.INSTALL COWL SIDE TRIM BOARD RH

Hide 67920 32.INSTALL DOOR SCUFF PLATE ASSEMBLY LH

Hide 67910 33.INSTALL DOOR SCUFF PLATE ASSEMBLY RH

Hide 75536B 34.INSTALL WINDSHIELD LOWER OUTSIDE MOULDING LH

a.

Attach the 5 clips to install a new moulding.


b.

Remove the protective tape from the edges of the moulding.


Hide 75535A 35.INSTALL WINDSHIELD LOWER OUTSIDE MOULDING RH

HINT:

Use the same procedure described for the LH side.


Hide 55781E 36.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 85211B 37.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 85221B 38.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85192 39.INSTALL WINDSHIELD WIPER ARM COVER

Hide 53867H 40.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 41.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

Hide 53828J 42.INSTALL FRONT FENDER SIDE PANEL PROTECTOR LH

Hide 53827K 43.INSTALL FRONT FENDER SIDE PANEL PROTECTOR RH

Hide 53292A 44.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 28800 45.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION