Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The combination meter assembly uses the fuel injection volume signal from the ECM, fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank assembly. Each gauge assembly has a variable resistor whose resistance changes according to the amount of fuel remaining. The gauge assemblies receive voltage from the combination meter assembly and change the voltage based on the resistance that changes according to the amount of fuel remaining in the fuel tank assembly. The combination meter assembly receives a fuel injection volume signal from the ECM and detects the voltage between each variable resistor and each resistor in the combination meter assembly, and operates the fuel receiver gauge.

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


HINT:

The fuel level warning light will come on when the fuel level is below 9.96 liters (10.5 US qts, 8.8 Imp. qts).


WIRING DIAGRAM

except 5L-E
E380756E01
2.76,0.656 3.219,0.854 0.458,0.198 10 false S5 0.719,2.583 2.99,2.844 2.271,0.26 10 false Fuel Suction Plate Sub-assembly 2.76,1.135 3.219,1.333 0.458,0.198 10 false S5 2.76,1.625 3.219,1.823 0.458,0.198 10 false S5 2.771,0.479 3.229,0.677 0.458,0.198 10 false 1*1 2.781,0.958 3.24,1.156 0.458,0.198 10 false 3*1 2.781,1.448 3.24,1.646 0.458,0.198 10 false 2*1 3.125,1.635 3.583,1.833 0.458,0.198 10 false R51 3.115,1.135 3.573,1.333 0.458,0.198 10 false R51 3.115,0.667 3.573,0.865 0.458,0.198 10 false R51 3.135,0.469 3.594,0.667 0.458,0.198 10 false 1*2 3.135,0.969 3.594,1.167 0.458,0.198 10 false 3*2 3.135,1.448 3.594,1.646 0.458,0.198 10 false 2*2 2.417,0.563 2.875,0.76 0.458,0.198 10 false FV 2.417,1.042 2.875,1.24 0.458,0.198 10 false FR 2.406,1.542 2.865,1.74 0.458,0.198 10 false FE 1.01,1.885 2.229,2.281 1.219,0.396 10 false Fuel Sender Gauge Assembly 0.99,1.667 1.448,1.865 0.458,0.198 10 false A 4.708,0.563 5.167,0.76 0.458,0.198 10 false FV 4.698,1.031 5.156,1.229 0.458,0.198 10 false FR 4.688,1.521 5.146,1.719 0.458,0.198 10 false FE&B 4.417,0.552 4.875,0.75 0.458,0.198 10 false 24 4.417,1.031 4.875,1.229 0.458,0.198 10 false 27 4.458,1.521 4.917,1.719 0.458,0.198 10 false 3 5.823,1.99 6.281,2.188 0.458,0.198 10 false CPU 4.708,5.625 5.167,5.823 0.458,0.198 10 false G304 4.708,5.802 6.948,6.073 2.24,0.271 10 false Combination Meter Assembly 0.125,5.865 1.271,6.104 1.146,0.24 10 false *1: for 5Door 0.125,6.177 1.302,6.375 1.177,0.198 10 false *2: for 3Door 0.833,5.594 3.375,5.833 2.542,0.24 10 false Fuel Tank Vent Tube Sub-assembly*3 1.76,0.688 2.219,0.885 0.458,0.198 10 false 3 1.76,1.146 2.219,1.344 0.458,0.198 10 false 2 1.771,1.625 2.229,1.823 0.458,0.198 10 false 1 2.375,4.333 2.833,4.531 0.458,0.198 10 false FV2 1.76,3.948 2.219,4.146 0.458,0.198 10 false 1 1.76,4.438 2.219,4.635 0.458,0.198 10 false 3 1.771,3.469 2.229,3.667 0.458,0.198 10 false 2 4.479,3.344 5,3.552 0.521,0.208 10 false 2 4.688,3.823 5.146,4.021 0.458,0.198 10 false FR*3 2.344,3.354 2.802,3.552 0.458,0.198 10 false FE2 2.74,3.354 3.198,3.552 0.458,0.198 10 false 1 2.729,3.802 3.188,4 0.458,0.198 10 false 4 2.708,4.323 3.167,4.521 0.458,0.198 10 false 5 4.417,3.823 4.938,4.031 0.521,0.208 10 false 24 4.417,4.323 4.938,4.531 0.521,0.208 10 false 25 4.708,4.344 5.167,4.542 0.458,0.198 10 false L*3 2.354,3.813 2.813,4.01 0.458,0.198 10 false FR2 4.688,3.365 5.146,3.563 0.458,0.198 10 false FE*3 0.823,5.396 1.281,5.594 0.458,0.198 10 false t1*3 0.969,4.729 2.531,5.073 1.563,0.344 10 false NO.2 Fuel Sender Gauge Assembly 0.135,6.5 2.281,6.708 2.146,0.208 10 false *3: for Double Tank Type

E380757E01
0.344,5.198 2.677,5.385 2.333,0.188 10 false Fuel Tank Vent Tube Sub-assembly*1 0.396,2.313 2.729,2.5 2.333,0.188 10 false Fuel Tank Vent Tube Assembly 0.344,5 2.677,5.188 2.333,0.188 10 false t1*1 0.406,4.406 2.74,4.594 2.333,0.188 10 false NO.2 Fuel Sender Gauge Assembly 2.385,3.365 3.063,3.521 0.677,0.156 10 false FR2 2.417,3.958 3.094,4.115 0.677,0.156 10 false FV2 2.792,3.354 3.469,3.51 0.677,0.156 10 false 4 2.792,3.958 3.469,4.115 0.677,0.156 10 false 5 2.052,3.99 2.729,4.146 0.677,0.156 10 false 2 0.938,3.979 1.615,4.135 0.677,0.156 10 false 1 4.719,4.927 5.396,5.083 0.677,0.156 10 false ET*1 4.479,4.927 5.156,5.083 0.677,0.156 10 false 5 4.688,3.969 5.365,4.125 0.677,0.156 10 false TE 4.688,3.354 5.365,3.51 0.677,0.156 10 false L 4.5,3.365 5.177,3.521 0.677,0.156 10 false 8 4.448,3.958 5.125,4.115 0.677,0.156 10 false 23 4.74,5.594 5.427,5.792 0.688,0.198 10 false G6 4.74,5.792 6.865,6.083 2.125,0.292 10 false Combination Meter Assembly 5.813,2.729 6.49,2.885 0.677,0.156 10 false CPU 4.688,4.396 5.365,4.552 0.677,0.156 10 false E2 4.427,4.406 5.104,4.563 0.677,0.156 10 false 21 0.906,1.115 1.583,1.271 0.677,0.156 10 false 1 2.073,1.125 2.75,1.281 0.677,0.156 10 false 2 2.49,0.51 3.167,0.667 0.677,0.156 10 false FS 2.802,1.115 3.479,1.271 0.677,0.156 10 false 3 2.802,0.531 3.479,0.688 0.677,0.156 10 false 2 2.479,1.115 3.156,1.271 0.677,0.156 10 false FE 0.646,1.563 2.979,1.75 2.333,0.188 10 false Fuel Sender Gauge Assembly 0.656,1.396 1.333,1.552 0.677,0.156 10 false A 4.688,0.521 5.365,0.677 0.677,0.156 10 false L 4.688,1.135 5.365,1.292 0.677,0.156 10 false E 4.479,0.51 5.156,0.667 0.677,0.156 10 false 9 4.406,1.115 5.083,1.271 0.677,0.156 10 false 24 0.208,6.406 2.542,6.594 2.333,0.188 10 false *1: for Double Tank Type

PROCEDURE

1.CHECK FOR DTC

b.

Recheck for DTCs and check that no DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
DTC B1500 and B1501 is not output A
DTC B1500 is output B
DTC B1501 is output C



A

2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)

B

C

2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender, Empty, Warning, 1/ 4, 1/2, 3/4, Full or Sender F -

OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK VEHICLE TYPE

NG

REPLACE COMBINATION METER ASSEMBLY

3.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
except 5L-E (for Single Tank Type) A
except 5L-E (for Double Tank Type) B
for 5L-E (for Single Tank Type) C
for 5L-E (for Double Tank Type) D



A

4.CHECK FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)

B

9.CHECK FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)

C

17.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)

D

20.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
4.CHECK FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)
E284677C71
1.5,0.208 1.906,0.458 0.406,0.25 2.49,1.76 2.354,1.115 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.542,0.25 1.969,0.448 0.427,0.198 10 false G304 2.427,1.802 2.74,1.958 0.313,0.156 10 false FV
*a Component with harness connected
(Combination Meter Assembly)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-24 (FV) - Body ground Engine switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

5.CHECK FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

5.CHECK FUEL SENDER GAUGE ASSEMBLY
E284677C66
1.5,0.208 1.906,0.458 0.406,0.25 2.052,1.115 1.01,1.646 true 2.438,1 2.708,1.625 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.542,0.25 2,0.49 0.458,0.24 10 false G304 2.542,1.656 3.052,1.865 0.51,0.208 10 false FE&B 0.802,1.635 1.115,1.792 0.313,0.156 10 false FR
*a Component with harness connected
(Combination Meter Assembly)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-27 (FR) - G304-3 (FE&B) Engine switch on (IG) 0.2 to 4.7 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the S5*1 or R51*2 fuel suction plate sub-assembly connector.

*1: for 5Door

*2: for 3Door



b.

Disconnect the G304 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 5Door):
Tester Connection Condition Specified Condition
S5-3 (FR) - G304-27 (FR) Always Below 1 Ω
S5-2 (FE) - G304-3 (FE&B) Always Below 1 Ω
S5-1 (FV) - G304-24 (FV) Always Below 1 Ω
G304-27 (FR) - Body ground Always 10 kΩ or higher
G304-3 (FE&B) - Body ground Always 10 kΩ or higher
G304-24 (FV) - Body ground Always 10 kΩ or higher


Standard Resistance (for 3Door):
Tester Connection Condition Specified Condition
R51-3 (FR) - G304-27 (FR) Always Below 1 Ω
R51-2 (FE) - G304-3 (FE&B) Always Below 1 Ω
R51-1 (FV) - G304-24 (FV) Always Below 1 Ω
G304-27 (FR) - Body ground Always 10 kΩ or higher
G304-3 (FE&B) - Body ground Always 10 kΩ or higher
G304-24 (FV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FUEL SENDER GAUGE ASSEMBLY


Result:
Proceed to
OK
NG



OK

8.INSPECT FUEL SUCTION PLATE SUB-ASSEMBLY

NG

8.INSPECT FUEL SUCTION PLATE SUB-ASSEMBLY
E158805C89
1.927,0.219 2.427,0.469 0.5,0.25 0.333,3.667 0.75,3.917 0.417,0.25 0.958,0.229 1.458,0.479 0.5,0.25 2.083,1.271 2.542,1.948 2.542,1.948 2.74,1.948 true 1.729,1.219 2.281,0.844 2.281,0.844 2.479,0.844 true 1.354,1.26 1.021,0.927 1.021,0.927 0.771,0.927 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *A 2.063,0.292 2.5,0.521 0.438,0.229 10 false R51 0.51,3.729 0.844,3.979 0.333,0.25 10 false A 0.49,0.854 0.823,1.104 0.333,0.25 10 false FR 2.583,0.781 2.917,1.031 0.333,0.25 10 false FE 2.875,1.865 3.208,2.115 0.333,0.25 10 false FV 1.115,0.281 1.552,0.51 0.438,0.229 10 false S5 1.51,0.271 1.823,0.479 0.313,0.208 10 false *1 2.521,0.26 2.833,0.469 0.313,0.208 10 false *2
*A Component without harness connected
(Fuel Suction Plate Sub-assembly)
*1 for 5Door
*2 for 3Door


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 5Door):
Tester Connection Condition Specified Condition
S5-1 (FV) - A-3 Always Below 1 Ω
S5-2 (FE) - A-2 Always Below 1 Ω
S5-3 (FR) - A-1 Always Below 1 Ω


Standard Resistance (for 3Door):
Tester Connection Condition Specified Condition
R51-1 (FV) - A-3 Always Below 1 Ω
R51-2 (FE) - A-2 Always Below 1 Ω
R51-3 (FR) - A-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

9.CHECK FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)
E284677C69
1.5,0.208 1.906,0.458 0.406,0.25 2.802,1.615 2.396,1.135 true 2.167,1.719 2.25,1.115 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.542,0.25 1.969,0.448 0.427,0.198 10 false G304 2.781,1.667 3.094,1.823 0.313,0.156 10 false FV 2.104,1.771 2.417,1.927 0.313,0.156 10 false L
*a Component with harness connected
(Combination Meter Assembly)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-24 (FV) - Body ground Engine switch on (IG) 4.5 to 5.5 V
G304-25 (L) - Body ground Engine switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

10.CHECK FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

10.CHECK FUEL SENDER GAUGE ASSEMBLY
E284677C70
1.5,0.208 1.906,0.458 0.406,0.25 2.052,1.115 1.01,1.646 true 2.583,1.01 2.719,0.271 true 2.458,0.969 2.844,1.563 true 2.146,1.135 2.188,1.75 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.542,0.25 2,0.49 0.458,0.24 10 false G304 2.719,1.594 3.229,1.802 0.51,0.208 10 false FE&B 0.802,1.635 1.115,1.792 0.313,0.156 10 false FR 2.073,1.792 2.385,1.948 0.313,0.156 10 false FR 2.625,0.104 3.135,0.313 0.51,0.208 10 false FE
*a Component with harness connected
(Combination Meter Assembly)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-27 (FR) - G304-3 (FE&B) Engine switch on (IG) 0.2 to 4.7 V
G304-26 (FR) - G304-2 (FE) Engine switch on (IG) 0.2 to 4.7 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
11.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the S5*1 or R51*2 fuel suction plate sub-assembly connector.

*1: for 5Door

*2: for 3Door



b.

Disconnect the G304 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 5Door):
Tester Connection Condition Specified Condition
S5-3 (FR) - G304-27 (FR) Always Below 1 Ω
S5-2 (FE) - G304-3 (FE&B) Always Below 1 Ω
S5-1 (FV) - G304-24 (FV) Always Below 1 Ω
G304-27 (FR) - Body ground Always 10 kΩ or higher
G304-3 (FE&B) - Body ground Always 10 kΩ or higher
G304-24 (FV) - Body ground Always 10 kΩ or higher


Standard Resistance (for 3Door):
Tester Connection Condition Specified Condition
R51-3 (FR) - G304-27 (FR) Always Below 1 Ω
R51-2 (FE) - G304-3 (FE&B) Always Below 1 Ω
R51-1 (FV) - G304-24 (FV) Always Below 1 Ω
G304-27 (FR) - Body ground Always 10 kΩ or higher
G304-3 (FE&B) - Body ground Always 10 kΩ or higher
G304-24 (FV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (FUEL TANK VENT TUBE ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (FUEL TANK VENT TUBE ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the t1 fuel tank vent tube assembly connector.


b.

Disconnect the G304 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
t1-4 (FR2) - G304-26 (FR) Always Below 1 Ω
2t1-1 (FE) - G304-3 (FE) Always Below 1 Ω
t1-5 (FV2) - G304-25 (L) Always Below 1 Ω
G304-26 (FR) - Body ground Always 10 kΩ or higher
G304-2 (FE) - Body ground Always 10 kΩ or higher
G304-25 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT FUEL SENDER GAGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT FUEL SENDER GAGE ASSEMBLY


Result:
Proceed to
OK
NG



OK

14.INSPECT FUEL SENDER GAGE ASSEMBLY NO.2

NG

14.INSPECT FUEL SENDER GAGE ASSEMBLY NO.2

OK

15.INSPECT FUEL SUCTION PLATE SUB-ASSEMBLY

NG

15.INSPECT FUEL SUCTION PLATE SUB-ASSEMBLY
E158805C89
1.927,0.219 2.427,0.469 0.5,0.25 0.333,3.667 0.75,3.917 0.417,0.25 0.958,0.229 1.458,0.479 0.5,0.25 2.083,1.271 2.542,1.948 2.542,1.948 2.74,1.948 true 1.729,1.219 2.281,0.844 2.281,0.844 2.479,0.844 true 1.354,1.26 1.021,0.927 1.021,0.927 0.771,0.927 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *A 2.063,0.292 2.5,0.521 0.438,0.229 10 false R51 0.51,3.729 0.844,3.979 0.333,0.25 10 false A 0.49,0.854 0.823,1.104 0.333,0.25 10 false FR 2.583,0.781 2.917,1.031 0.333,0.25 10 false FE 2.875,1.865 3.208,2.115 0.333,0.25 10 false FV 1.115,0.281 1.552,0.51 0.438,0.229 10 false S5 1.51,0.271 1.823,0.479 0.313,0.208 10 false *1 2.521,0.26 2.833,0.469 0.313,0.208 10 false *2
*A Component without harness connected
(Fuel Suction Plate Sub-assembly)
*1 for 5Door
*2 for 3Door


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 5Door):
Tester Connection Condition Specified Condition
S5-1 (FV) - A-3 Always Below 1 Ω
S5-2 (FE) - A-2 Always Below 1 Ω
S5-3 (FR) - A-1 Always Below 1 Ω


Standard Resistance (for 3Door):
Tester Connection Condition Specified Condition
R51-1 (FV) - A-3 Always Below 1 Ω
R51-2 (FE) - A-2 Always Below 1 Ω
R51-3 (FR) - A-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.INSPECT FUEL TANK VENT TUBE ASSEMBLY

NG

16.INSPECT FUEL TANK VENT TUBE ASSEMBLY
E380660C01
1.688,2.74 2.094,2.969 0.406,0.229 0.833,2.583 0.667,2.583 0.667,2.583 1.688,1.104 true 1.5,2.333 1.313,2.333 1.313,2.333 1.865,1.073 true 2.083,1.917 1.833,1.917 1.833,1.917 2.063,1.083 true 1.594,0.375 1.906,0.573 0.313,0.198 10 false *a 0.906,2.479 1.219,2.677 0.313,0.198 10 false 1 1.573,2.25 1.885,2.448 0.313,0.198 10 false 2 2.156,1.833 2.469,2.031 0.313,0.198 10 false 3 0.188,2.99 0.5,3.188 0.313,0.198 10 false *b 1.813,2.781 2.125,2.979 0.313,0.198 10 false t1
*a Fuel Tank Vent Tube Assembly
*b Component without harness connected
(Fuel Tank Vent Tube Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
t1-1 (FE2) - 2 Always Below 1 Ω
t1-4 (FR2) - 1 Always Below 1 Ω
t1-5 (FV2) - 3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

17.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
a.

Disconnect the G6 combination meter assembly connector.


b.

Disconnect the S5 fuel sender gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-9 (L) - S5-2 (FS) Always Below 1 Ω
G6-24 (E) - S5-3 (FE) Always Below 1 Ω
G6-21 (E2) - Body ground Always Below 1 Ω
G6-16 (L) or S5-2 (FS) - Body ground Always 10 kΩ or higher
G6-15 (E) or S5-3 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.INSPECT FUEL TANK VENT TUBE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT FUEL TANK VENT TUBE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

19.INSPECT FUEL TANK VENT TUBE ASSEMBLY

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

19.INSPECT FUEL TANK VENT TUBE ASSEMBLY
E158805C90
0.333,3.667 0.75,3.917 0.417,0.25 1.458,0.229 1.958,0.479 0.5,0.25 1.417,1.323 0.958,1.823 0.958,1.823 0.698,1.823 true 1.729,1.219 2.281,0.844 2.281,0.844 2.479,0.844 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *A 0.51,3.729 0.844,3.979 0.333,0.25 10 false A 2.583,0.781 2.917,1.031 0.333,0.25 10 false FS 0.469,1.76 0.802,2.01 0.333,0.25 10 false FE 1.625,0.281 2.063,0.51 0.438,0.229 10 false S5
*a Component without harness connected
(Fuel Tank Vent Tube Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S5-2 (FS) - A-2 Always Below 1 Ω
S5-3 (FE) - A-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL TANK VENT TUBE ASSEMBLY

20.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
a.

Disconnect the G6 combination meter assembly connector.


b.

Disconnect the S5 fuel sender gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-9 (L) - S5-2 (FS) Always Below 1 Ω
G6-24 (E) - S5-3 (FE) Always Below 1 Ω
G6-21 (E2) - Body ground Always Below 1 Ω
G6-16 (L) or S5-2 (FS) - Body ground Always 10 kΩ or higher
G6-15 (E) or S5-3 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
a.

Disconnect the G6 combination meter assembly connector.


b.

Disconnect the t1 fuel sender gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-8 (L) - t1-4 (FR2) Always Below 1 Ω
G6-23 (FE) - t1-5 (FV2) Always Below 1 Ω
G6-5 (ET) - Body ground Always Below 1 Ω
G6-8 (L) or t1-4 (FR2) - Body ground Always 10 kΩ or higher
G6-23 (FE) or t1-5 (FV2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.INSPECT FUEL SENDER GAGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.INSPECT FUEL SENDER GAGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

23.INSPECT FUEL SENDER GAGE ASSEMBLY NO.2

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

23.INSPECT FUEL SENDER GAGE ASSEMBLY NO.2
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

24.INSPECT FUEL TANK VENT TUBE ASSEMBLY

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

24.INSPECT FUEL TANK VENT TUBE ASSEMBLY
E158805C90
0.333,3.667 0.75,3.917 0.417,0.25 1.458,0.229 1.958,0.479 0.5,0.25 1.417,1.323 0.958,1.823 0.958,1.823 0.698,1.823 true 1.729,1.219 2.281,0.844 2.281,0.844 2.479,0.844 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *A 0.51,3.729 0.844,3.979 0.333,0.25 10 false A 2.583,0.781 2.917,1.031 0.333,0.25 10 false FS 0.469,1.76 0.802,2.01 0.333,0.25 10 false FE 1.625,0.281 2.063,0.51 0.438,0.229 10 false S5
*a Component without harness connected
(Fuel Tank Vent Tube Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S5-2 (FS) - A-2 Always Below 1 Ω
S5-3 (FE) - A-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

25.INSPECT FUEL TANK VENT TUBE ASSEMBLY

NG

REPLACE FUEL TANK VENT TUBE ASSEMBLY

25.INSPECT FUEL TANK VENT TUBE ASSEMBLY
E349680C02
1.5,2.813 1.906,3.021 0.406,0.208 1.698,1.802 1.698,0.844 false 2.094,1.802 2.094,0.833 false 0.688,4.292 0.844,4.292 0.844,4.292 1.563,3.979 false 2.75,4.313 2.594,4.313 2.594,4.313 1.802,3.979 false 0.635,0.104 0.948,0.302 0.313,0.198 10 false *a 1.656,1.844 1.813,2.042 0.156,0.198 10 false 1 2.063,1.844 2.219,2.042 0.156,0.198 10 false 2 0.948,3.021 1.26,3.219 0.313,0.198 10 false *b 0.406,4.219 0.917,4.479 0.51,0.26 10 false FV2 2.813,4.229 3.25,4.417 0.438,0.188 10 false FR2 1.646,2.833 1.865,3.073 0.219,0.24 10 false t1
*a Fuel Tank Vent Tube Assembly
*b Component without harness connected
(Fuel Tank Vent Tube Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
t1-4 (FR2) - 1 Always Below 1 Ω
t1-5 (FV2) - 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL TANK VENT TUBE ASSEMBLY