Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › EXHAUST MANIFOLD W/ TURBOCHARGER › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053680 1GD-FTV INTAKE / EXHAUST _0260655 EXHAUST MANIFOLD W/ TURBOCHARGER A

1GD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A344970

Using an E10 "TORX" socket wrench, install the 3 stud bolts at the positions shown in the illustration.

Torque:
14.7 N*m (150 kgf*cm, 11 ft.*lbf)


b.
A344969

Using an E8 "TORX" socket wrench, install the 4 stud bolts at the positions shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Using an E5 "TORX" socket wrench, install the 4 stud bolts at the positions shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

A425661C01
0.083,0.052 0.396,0.208 0.313,0.156 10 false *A 3.927,0.073 4.24,0.229 0.313,0.156 10 false *B
*A w/o Urea SCR System *B w/ Urea SCR System



Hide 17275 2.INSTALL COMPRESSOR OUTLET ELBOW

a.

except Cold Area Specification Vehicles:

Install the hose clamp with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install a new gasket.


c.

Install the compressor outlet elbow with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17274 3.INSTALL COMPRESSOR INLET ELBOW

a.

Install a new gasket.


b.

Using an E8 "TORX" socket wrench, install the compressor inlet elbow with the stud bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Install the compressor inlet elbow to the turbocharger sub-assembly with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Install the compressor elbow stay with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16027 4.INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.

Install a new gasket.


b.

Temporarily install the turbo water pipe sub-assembly with the bolt and 2 nuts.


c.

Tighten the bolt and 2 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


d.

Connect the No. 1 turbo water hose and No. 2 turbo water hose to the No. 1 turbo water pipe sub-assembly and slide the 2 hose clips to secure the hoses.


Hide 15407 5.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY

a.
A345118C03
2.448,1.802 2.76,1.958 0.313,0.156 10 true *b 0.729,1.813 1.042,1.969 0.313,0.156 10 true *a
*a NG
*b OK


Install a new gasket as shown in the illustration.

NOTICE:

Do not install the gasket upside down.



b.

Temporarily install the turbo oil inlet pipe subassembly with the 2 nuts.


Hide 17141 6.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

a.

Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install a new gasket (No. 1 EGR pipe sub-assembly side) to the exhaust manifold.


c.

Install a new gasket to the turbocharger sub-assembly.


d.

Temporarily install the turbocharger sub-assembly with 3 new nuts.


e.
A454517C01
0.99,1.875 1.24,1.875 true 1.292,1.813 1.604,1.969 0.313,0.156 10 false *1
*1 Collar
V100136

Engine Side


Install a new gasket (cylinder head side), and then temporarily install the exhaust manifold with 8 new nuts, 8 new collars and 8 new washers.

NOTICE:

Make sure that the side of the collar with the smaller diameter faces the exhaust manifold.



f.

Install a new gasket on the union bolt side to turbo oil inlet pipe sub-assembly.


g.

Temporarily install the union bolt.


Hide 15474 7.INSTALL TURBO OIL OUTLET PIPE

a.

Install a new gasket to the turbo oil outlet pipe.

NOTICE:

The claws of the gasket must face the turbo oil outlet pipe.



b.

Install the turbo oil outlet pipe with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

w/ Cover:

Install the cover to the turbo oil outlet hose.


d.

Connect the turbo oil outlet hose to the turbo oil outlet pipe, turbo oil inlet pipe and slide the 2 hose clips to secure the hoses.


Hide 17293 8.TEMPORARILY INSTALL TURBOCHARGER STAY

a.

Temporarily install the turbocharger stay to the turbocharger sub-assembly, with 3 bolts and nut.


Hide 17141 9.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

a.
A455228N01
1.354,0.156 1.521,0.323 0.167,0.167 10 true 1 2.052,0.135 2.219,0.302 0.167,0.167 10 true 2 2.344,1.521 2.51,1.688 0.167,0.167 10 true 3 1.635,1.563 1.802,1.729 0.167,0.167 10 true 4 0.219,1.573 0.385,1.74 0.167,0.167 10 true 5 0.583,0.167 0.75,0.333 0.167,0.167 10 true 6 2.646,0.156 2.813,0.323 0.167,0.167 10 true 7 2.677,1.49 2.844,1.656 0.167,0.167 10 true 8

Tighten the exhaust manifold with turbocharger sub-assembly, to the cylinder head sub-assembly with 8 nuts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:

Tighten the nuts in the order shown in the illustration.



b.

Tighten the turbocharger sub-assembly, to the exhaust manifold with the 3 nuts.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)


c.

Tighten the 2 nuts and then union bolt of the turbo oil inlet pipe sub-assembly.

Torque:
for nut : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for union bolt : 36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

If the connecting part of the union bolt gasket is cracked, remove the connecting part.



Hide 17293 10.TIGHTEN TURBOCHARGER STAY

a.
U169510E02
1.542,0.208 1.802,0.5 0.26,0.292 10 true 1 2.5,0.708 2.76,1 0.26,0.292 10 true 2 0.385,2.292 0.573,2.583 0.188,0.292 10 true 4 1.396,3.052 1.583,3.344 0.188,0.292 10 true 3

Tighten the 3 bolts and nut of the turbocharger stay in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 87101 11.INSTALL VISCOUS HEATER NO.1 BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)

U169550C01
2.896,1.583 3.104,1.823 0.208,0.24 10 false 1 0.677,0.396 0.885,0.635 0.208,0.24 10 false 2 1.208,2.271 1.417,2.51 0.208,0.24 10 true 3 2.635,0.396 2.844,0.635 0.208,0.24 10 false 4
V100135

No. 1 Viscous Heater Bracket Bolt
V100136

No. 4 Engine Harness Bolt


a.

Temporarily install the No. 1 viscous heater bracket sub-assembly with 4 bolts.


b.

Tighten the 4 bolts and of the No. 1 viscous heater bracket sub-assembly in the order shown in the illustration.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


c.

Connect the No. 4 engine harness with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


d.

Connect the wire harness.


Hide 12.INSTALL OIL COOLER TUBE BRACKET AND WIRE HARNESS CLAMP BRACKET

a.

Connect the wire harness clamp bracket with the bolt.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


b.

for Automatic Transmission:

Connect the oil cooler tube bracket with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 47 in.*lbf)


Hide 25601 13.CONNECT NO. 1 EGR PIPE SUB-ASSEMBLY

a.

Connect the No. 1 EGR pipe sub-assembly with 2 new nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 16284 14.CONNECT TURBO WATER HOSE

a.

Connect the No. 1 turbo water hose and No. 2 turbo water hose to the water outlet sub-assembly, engine water pump assembly and slide the 2 hose clips to secure the hoses.

NOTICE:

The turbocharger sub-assembly may be damaged if the No. 1 turbo water hose and No. 2 turbo water hose are connected to the wrong locations.



Hide 16268 15.CONNECT NO. 1 WATER BY-PASS PIPE

Hide 16.CONNECT WATER BY-PASS HOSE (w/ Urea SCR System)

a.

Connect the No. 4 turbo water hose to the turbocharger sub-assembly and No. 1 turbo water pipe sub-assembly and slide the 2 hose clips to secure the hoses.


b.

Connect the No. 21 water by-pass hose to the turbocharger sub-assembly and No. 1 water by-pass pipe and slide the 2 hose clips to secure the hoses.


Hide 12203 17.INSTALL PCV HOSE (except Cold Area Specification Vehicles)

a.

Attach the clamp and install the PCV hose.


b.

Slide the 2 hose clips to secure the hoses.


Hide 12203 18.INSTALL PCV PIPE (for Cold Area Specification Vehicles)

a.

w/o Urea SCR System

i.

Connect the PCV pipe to the compressor inlet elbow, cylinder head cover sub-assembly and slide the 2 hose clips to secure the hoses.


ii.

Install the PCV pipe with the bolt to the compressor outlet elbow.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Connect the No. 19 water by-pass hose to the compressor inlet elbow and slide the hose clip to secure the hoses.


iv.

Install the No. 20 water by-pass hose to the PCV pipe and No. 1 water by-pass pipe, and slide the 2 hose clips to secure the hoses.



b.

w/ Urea SCR System:

i.

Connect the PCV pipe to the compressor inlet elbow, cylinder head cover sub-assembly and slide the 2 hose clips to secure the hoses.


ii.

Install the PCV pipe with the 2 bolts to the compressor outlet elbow.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Connect the No. 19 water by-pass hose to the compressor inlet elbow and slide the hose clip to secure the hoses.


iv.

Install the No. 20 water by-pass hose to the PCV pipe and No. 1 water by-pass pipe, and slide the 2 hose clips to secure the hoses.



Hide 16279 19.INSTALL NO. 3 WATER BY-PASS PIPE

a.

Connect the 2 water hoses to the oil cooler assembly and No. 2 water by-pass pipe, and slide the 2 hose clips to secure the hoses.


b.

Install the No. 3 water by-pass pipe with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

for Cold Area Specification Vehicles:

Install the water hose to the compressor inlet elbow and No. 3 water by-pass pipe, and slide the 2 hose clips to secure the hoses.


Hide 87209D 20.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 87120G 21.INSTALL VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (for Cold Area Specification Vehicles)

Hide 22.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

for Cold Area Specification Vehicles:

Connect the wire harness clamps.


Hide 17801 23.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case.


Hide 17705 24.CONNECT AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE

a.

Attach the 4 clips to install the air cleaner cap sub-assembly with air cleaner hose.


b.

Tighten the hose clamp.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Connect the mass air flow meter connector and attach the 2 wire harness clamps.


Hide 16470 26.INSTALL RADIATOR RESERVOIR ASSEMBLY

Hide 16640 27.INSTALL INTERCOOLER RESERVOIR ASSEMBLY (w/ Urea SCR System)

Hide 16554B 28.INSTALL NO. 4 SUB-RADIATOR HOSE (w/ Urea SCR System)

Hide 16553B 29.INSTALL NO. 3 SUB-RADIATOR HOSE (w/ Urea SCR System)

Hide 161B0 30.INSTALL ELECTRIC WATER PUMP ASSEMBLY (w/ Urea SCR System)

Hide 16551B 31.INSTALL NO. 1 SUB-RADIATOR HOSE (w/ Urea SCR System)

Hide 16552B 32.INSTALL NO. 2 SUB-RADIATOR HOSE (w/ Urea SCR System)

Hide 16571C 33.INSTALL NO. 1 RADIATOR HOSE

Hide 82123 34.INSTALL NO. 3 ENGINE WIRE (for Cold Area Specification Vehicles)

Hide 44306 35.CONNECT VANE PUMP OIL RESERVOIR SUB-ASSEMBLY

Hide 17342F 36.INSTALL NO. 2 INTERCOOLER AIR HOSE (w/o Urea SCR System)

Hide 17341K 37.INSTALL INTERCOOLER AIR HOSE (w/o Urea SCR System)

Hide 17940D 38.INSTALL INTERCOOLER ASSEMBLY (w/ Urea SCR System)

Hide 25051 39.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 40.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION