Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY (for 2TR-FE) › from 2020.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260776 AUTOMATIC TRANSMISSION ASSEMBLY(for 2TR-FE) A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 2TR-FE)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL WIRING HARNESS CLAMP BRACKET

HINT:

It is not necessary to remove the wire harness clamp brackets unless they are being replaced.


a.

Attach the 8 wire harness clamps and install the 4 wire harness clamp brackets to the wire harness.


Hide 32000 2.INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY

a.
C354124E01
1.292,0.865 0.99,0.26 0.99,0.26 0.833,0.26 true 1.406,2.313 1.229,2.896 1.229,2.896 1.073,2.896 true 0.583,0.156 0.781,0.354 0.198,0.198 10 false *a 0.823,2.802 1.021,3 0.198,0.198 10 false *b 2.708,0.76 2.906,0.958 0.198,0.198 10 false *a 3.031,1.625 3.229,1.823 0.198,0.198 10 false *b 2.354,0.219 2.552,0.417 0.198,0.198 10 false A

Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transmission assembly contact surface of the engine assembly (*a) and the torque converter assembly contact surface of the drive plate (*b).

Text in Illustration
*a Engine Assembly Surface
*b Drive Plate Surface


b.
C326326E02
1.01,0.323 0.385,0.167 0.385,0.167 0.938,0.438 true 0.156,0.063 0.344,0.26 0.188,0.198 10 false *a

Align the matchmark on the automatic transmission case sub-assembly with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

Text in Illustration
*a Matchmark

NOTICE:

Install the torque converter assembly to the input shaft while keeping it horizontal.



c.
C326327E02
3.073,1.052 3.25,1.229 0.177,0.177 10 false *1

Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

Text in Illustration
*1 Front Oil Pump Oil Seal

NOTICE:
·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




d.
C326328E02
3.073,1.052 3.24,1.219 0.167,0.167 10 false *1

Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the automatic transmission case sub-assembly and insert the key of the torque converter assembly into the groove of the oil pump drive gear.

Text in Illustration
*1 Front Oil Pump Oil Seal

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




e.
C326329E01
2.35,0.236 2.495,0.413 0.144,0.177 10 B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transmission assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.




Hide 3516A 3.INSTALL TRANSMISSION OIL PAN HEAT INSULATOR

HINT:

It is not necessary to remove the transmission oil pan heat insulator unless it is being replaced.


a.

Install the transmission oil pan heat insulator to the automatic transmission assembly with the 3 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 33823 4.INSTALL TRANSMISSION CONTROL CABLE BRACKET

HINT:

It is not necessary to remove the transmission control cable bracket unless it is being replaced.


a.

Install the transmission control cable bracket to the automatic transmission assembly with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 35000 6.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C274145E02
1.396,1.01 1.042,1.01 false 1.76,1.167 2.104,1.51 2.104,1.51 2.26,1.51 true 0.844,0.917 1.031,1.125 0.188,0.208 10 false *1 2.302,1.427 2.521,1.625 0.219,0.198 10 false *2

Apply clutch spline grease to the circumference of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum spread:

About 1 g (0.0353 oz.)


Text in Illustration
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


b.
U167294E01
0.541,2.962 0.678,3.140 0.137,0.178 10 B 2.839,3.847 2.976,4.025 0.137,0.178 10 A 1.182,2.222 1.320,2.399 0.137,0.178 10 B 2.526,2.32 2.664,2.498 0.137,0.178 10 B 2.483,4.161 2.620,4.339 0.137,0.178 10 A 0.952,4.129 1.089,4.307 0.137,0.178 10 A 0.604,3.604 0.742,3.782 0.137,0.178 10 A

Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.

While keeping the engine assembly and automatic transmission assembly horizontal, align the 2 knock pins with the holes in the automatic transmission assembly and install the 7 bolts.

Torque:
for Bolt A : 37 N*m (377 kgf*cm, 27 ft.*lbf)
for Bolt B : 71 N*m (724 kgf*cm, 52 ft.*lbf)

NOTICE:
·

Do not use excessive force when installing the automatic transmission assembly.

·

Check that the torque converter assembly rotates.

·

Make sure that the wire harness or other similar items are not pinched between the contact surfaces.



HINT:
Bolt length
·

Bolt A: 45 mm (1.77 in.)

·

Bolt B: 55 mm (2.17 in.)




d.

Connect the breather hose to the engine assembly.


Hide 7.CONNECT WIRE HARNESS

a.

Tilt down the automatic transmission assembly.

NOTICE:

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.



b.

Connect the wire harness to the automatic transmission assembly with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Attach the 2 wire harness clamps.


d.

Attach the heated oxygen sensor connector to the wire harness clamp bracket.


e.

Connect the park/neutral position switch connector, transmission wire connector, 2 transmission revolution sensor connectors and transfer connector.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



f.

Connect the breather hose to the wire harness.


Hide 36478A 8.INSTALL TRANSMISSION BREATHER BRACKET

a.

Install the 2 clamps to the transmission breather bracket.

HINT:

It is not necessary to remove the transmission breather clamp unless it is being replaced.



b.

Install the transmission breather bracket to the automatic transmission assembly with the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


c.

Connect the 3 breather hoses and attach the wire harness clamp to the transmission breather bracket.


Hide 12371 9.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

It is not necessary to remove the rear No. 1 engine mounting insulator unless it is being replaced.


a.
C330293

Install the rear No. 1 engine mounting insulator to the automatic transmission assembly with the 4 bolts.

Torque:
73 N*m (739 kgf*cm, 53 ft.*lbf)

Text in Illustration
V100136

Front Side


Hide 51203 10.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the No. 3 frame crossmember sub-assembly to the body with the 4 bolts and 4 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Install the nuts so that they face the rear of the vehicle.


HINT:

Hold the bolts while tightening the nuts.



b.

Connect the No. 3 frame crossmember sub-assembly to the rear No. 1 engine mounting insulator with the 4 bolts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 51225B 11.INSTALL FRONT SUSPENSION MEMBER BRACKET LH AND RH

a.

Install the front suspension member bracket LH and RH with the 8 bolts.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)


Hide 12.CONNECT OIL COOLER TUBE

a.

Connect the ends of the 2 oil cooler tubes to the automatic transmission assembly by hand.


b.

Connect the 2 oil cooler tubes to the engine assembly with the 2 bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Install the flexible hose clamp to the automatic transmission assembly.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


d.
C324535E05
1.875,1.333 2.031,1.51 0.156,0.177 10 true *a

Using a 17 mm union nut wrench, tighten the 2 oil cooler tubes.

Torque:
Specified tightening torque : 34 N*m (350 kgf*cm, 25 ft.*lbf)

Text in Illustration
*a Torque Wrench Fulcrum Length

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

(See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)

·

When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 29 N*m (300 kgf*cm, 22 ft.*lbf)




Hide 82046A 13.INSTALL NO. 1 BODY GROUND WIRE SUB-ASSEMBLY

a.
C330297

Connect the No. 1 body ground wire sub-assembly to the automatic transmission assembly with the bolt as shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
V100136

Rear Side

HINT:

Make contact with the terminal stopper.



Hide 35979B 14.INSTALL TRANSMISSION INSULATOR RH

Hide 33820B 15.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C326305E02
1.021,0.042 1.198,0.229 0.177,0.188 10 true N

Turn the control shaft lever clockwise until it stops, and then return the control shaft lever counterclockwise 2 notches to N.


b.

Connect the end of the transmission control shift cable assembly to the transmission control shaft lever LH.


c.

Move the shift lever to N, and with the cable end lightly pushed toward the rear of the vehicle, install the transmission control cable assembly to the transmission control shaft lever LH with the nut.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)

HINT:

Tighten the nut with no slack in the transmission control cable assembly.



d.

Connect the transmission control shift cable assembly to the transmission control cable bracket with a new clip.


Hide 17118 16.INSTALL MANIFOLD STAY

a.
U149074E03
2.667,0.719 2.802,0.896 0.135,0.177 10 false A 0.646,0.948 0.781,1.125 0.135,0.177 10 false B 0.594,1.458 0.729,1.635 0.135,0.177 10 false C

Install the manifold stay to the automatic transmission assembly and exhaust manifold with the 3 bolts.

Torque:
for Bolt A (M8 bolt) : 30 N*m (306 kgf*cm, 22 ft.*lbf)
for Bolt B (M10 bolt) : 44 N*m (449 kgf*cm, 32 ft.*lbf)
for Bolt C (M12 bolt) : 71 N*m (724 kgf*cm, 52 ft.*lbf)


Hide 32101A 17.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)

NOTICE:

Install the black colored bolt first, and then the 5 silver colored bolts.



Hide 11354 18.INSTALL FLYWHEEL HOUSING DUST SEAL

a.

Install the flywheel housing dust seal to the engine assembly.


Hide 17410 20.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 37140 21.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110 22.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 24.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 25. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

(See pageGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE)

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

(See pageGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART)


Hide 29.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.


Hide 51450 30.INSTALL REAR ENGINE UNDER COVER ASSEMBLY

Hide 51405A 31.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 32. RESET MEMORY

NOTICE:

If automatic transmission parts have been replaced, refer to the Parts Replacement Compensation Table to determine if any additional operations are necessary.

(See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 2TR-FE)>INITIALIZATION)