When the shift lever is in S, the shift range can be changed using the shift paddle switches. It is also possible to select the shift range when the vehicle is being driven with the shift lever in D by operating the shift paddle switches.
Refer to the SRS precaution before troubleshooting.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sport Shift Up SW | Sport shift up switch status | OFF or ON | ·
ON: "+" shift paddle operated (up-shift) ·
OFF: "+" shift paddle not operated (up-shift) |
- |
| Sport Shift Down SW | Sport shift down switch status | OFF or ON | ·
ON: "-" shift paddle operated (down-shift) ·
OFF: "-" shift paddle not operated (down-shift) |
- |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
| *a | Rear view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Disconnect the transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G184-21 (SFTU) - Body ground | "+" shift paddle operated and held (up-shift) | Below 2.5 Ω |
| G184-20 (SFTD) - Body ground | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| G184-21 (SFTU) - Body ground | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| G184-20 (SFTD) - Body ground | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
Disconnect the spiral cable sub-assembly connector.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G208-2 (ECC) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the spiral cable sub-assembly connector.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G184-20 (SFTD) - G208-7 (SDN) | Always | Below 1 Ω |
| G184-21 (SFTU) - G208-14 (SUP) | Always | Below 1 Ω |
| G184-20 (SFTD) or G208-7 (SDN) - Body ground | Always | 10 kΩ or higher |
| G184-21 (SFTU) or G208-14 (SUP) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Steering Pad Switch Assembly Connector
(to Spiral Cable Sub-assembly) |
Disconnect the steering pad switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z16-6 (SUP) - z16-7 (ECC) | "+" shift paddle operated and held (up-shift) | Below 2.5 Ω |
| z16-12 (SDN) - z16-7 (ECC) | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| z16-6 (SUP) - z16-7 (ECC) | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| z16-12 (SDN) - z16-7 (ECC) | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Shift Paddle Switch LH |
Remove the shift paddle switch LH.
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| SDN - ECC | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| SDN - ECC1 | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| SDN - ECC | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| SDN - ECC1 | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Shift Paddle Switch RH |
Remove the shift paddle switch RH.
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| SUP - ECC1 | "+" shift paddle operated and held (up-shift) | Below 2.5 Ω |
| SUP - ECC1 | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Steering Pad Switch Assembly) |
Disconnect the No. 1 switch wire connector.
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z25-2 (SUP) - z25-7 (ECC) | "+" shift paddle operated and held (up-shift) | Below 2.5 Ω |
| z25-3 (SDN) - z25-7 (ECC) | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| z25-2 (SUP) - z25-7 (ECC) | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| z25-3 (SDN) - z25-7 (ECC) | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG