Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _091546 STOP AND START _0437376 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P160300  Engine Stall History  


DESCRIPTION

If the engine stalls or fails to start while stop and start control is operating, DTC P160300 will be stored. Using the GTS, the freeze frame data recorded the moment the DTC is stored can be read. Serviceability has been enhanced by enabling the cause of an engine stall or engine start failure which occurred while stop and start control was operating to be checked using the freeze frame data.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P160300 Engine Stall History Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·

Engine stopped by stop and start control and collision or low battery voltage detected

·

Collision detection signal received from the airbag sensor assembly and mode changed to "stalled"*1


Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·

Engine being restarted by stop and start control and collision detected

·

Collision detection signal received from the airbag sensor assembly and mode changed to "stalled"*1


Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·

Engine being restarted by stop and start control and restart fails.

·

Using the NE signal, complete combustion is identified 0.6 seconds after the engine stop judgment*2 was made or complete combustion does not occur even after the starter assembly has operated for a certain amount of time (NE signal is normal).


Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·

Engine being restarted by stop and start control and restart fails.

·

Engine speed signal from the ECM not received via CAN communication (NE signal is abnormal*3).


Detection Conditions: Always
Sensors/components used for detection: park/neutral position switch assembly, airbag sensor assembly, battery, crank position sensor, STA signal circuit, ECM
·

Wire harness or connector

·

CAN communication system

·

Airbag system

·

ECD system

·

Starter assembly

·

Engine stop and start ECU


Does not come on DTC stored SAE Code: P1603

*1: The mode "stalled" represents a state in which engine restart is prohibited/canceled due to a collision being detected and restart is not preferable. In this situation, "IG" is displayed for the Data List item "Stop&Start of Eng State". If the mode changes to "IG", engine start by stop and start control is prohibited and the engine can only be started by operating the push start switch assembly.

*2: Engine stop judgment is performed to judge whether the engine is stopped completely. The engine stop and start ECU judges that the engine is stopped when it does not receive an engine speed signal (NE signal) from the ECM for 0.6 seconds or more.

*3: The engine stop and start ECU stores DTC P033562.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the starter assembly, perform initialization of the number of starter operations stored in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the engine stop and start ECU or electromagnetic oil pump is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the starter assembly is replaced, "ST relay" and "ST NO. 2 relay" must be also replaced.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the engine stop and start ECU or electromagnetic oil pump is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



HINT:
·

If other DTCs are output, perform troubleshooting for this DTC first.

·

Unlike other DTCs that are stored due to a malfunction in parts, circuits or systems, DTC P160300 allows determination of a malfunctioning part according to problem symptoms and freeze frame data related to a problem recognized by the customer. As this DTC may be stored due to an operation by the customer, it is not necessary to service the vehicle unless the customer recognized a problem. Clear the DTCs and return the vehicle to the customer.

·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

·

Stop and Start Control Mode Transition:

A310520E04
0.427,1.563 1.844,2.156 1.417,0.594 10 false Driving status: Normal (engine runs and idles normally) 5.208,1.573 6.833,2.094 1.625,0.521 10 false Stop status: Engine stopped by stop and start control 2.813,0.25 4.156,0.615 1.344,0.365 10 false Stop request: Engine stop requested 2.844,1.5 4.208,1.833 1.365,0.333 10 false Start request: Engine start requested 2.885,2.76 4.094,3.115 1.208,0.354 10 false Engine stall status: Engine stopped 2.229,0.292 2.542,0.49 0.313,0.198 10 false *1 4.604,2.792 4.917,2.99 0.313,0.198 10 false *6 2.25,1.5 2.563,1.698 0.313,0.198 10 false *5 2.25,2.5 2.563,2.698 0.313,0.198 10 false *7 2.25,3.042 2.563,3.24 0.313,0.198 10 false *8 4.583,0.281 4.896,0.479 0.313,0.198 10 false *2 4.604,1.51 4.917,1.708 0.313,0.198 10 false *4 3.646,1.094 3.958,1.292 0.313,0.198 10 false *3 3.656,2.333 3.969,2.531 0.313,0.198 10 false *6

*1: Engine stop conditions are met.

*2: Engine stop judgment is determined.

*3: Engine start conditions are met before the engine is judged as stopped.

*4: Engine start conditions are met.

*5: Engine determined to be started (engine speed reaches a specified rpm).

*6: Collision detected and mode changed to "stalled".

*7: 0.6 seconds elapse after engine stop judgment is established.

*8: Engine is started using the push start switch assembly.




PROCEDURE

1.CHECK DTC OUTPUT (ECD SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes


e.

Read the DTCs.

Result:
Result Proceed to
ECD system DTCs are not output A
ECD system starting malfunction circuit DTC is output and starter assembly does not operate
ECD system starting malfunction circuit DTC is output and starter assembly operates B
DTCs other than ECD system starting malfunction circuit DTC are output


HINT:
·

According to the display on the GTS, check the freeze frame data item "Cranking Time" in the sets of freeze frame data.

·

If the value of "Cranking Time" is approximately 3 seconds, the stop and start control system or starter system may be malfunctioning.

·

If the value of "Cranking Time" is small (approximately 0.5 seconds or less: the minimum value varies depending on the model), the ECD system may be malfunctioning.

·

The Data List item "Cranking Time" indicates the length of time starter operation is requested by the engine stop and start ECU. If the engine speed exceeds the specified value, the engine stop and start ECU cancels its start request.





A

2.CHECK FREEZE FRAME DATA

B

2.CHECK FREEZE FRAME DATA
NOTICE:

The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


HINT:

Using the time-series freeze frame data, confirm the freeze frame data recorded the moment the DTC was stored and after the DTC was stored. This information can be useful when troubleshooting.


a.

According to the prompts on the GTS screen, read the time-series freeze frame data to confirm the vehicle conditions when an engine stall occurred while stop and start control was operating.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA


b.

Check the freeze frame data for engine stall history and engine start failure.

Result:
Tester Display Result Proceed to
Engine Stall History during Stop&Start (Collision or Battery Voltage Low) Yes A
Engine Stall History during Engine Starting (Collision) Yes
Engine Start Fail Yes B
Engine Stall History during Stop&Start (Reduced Voltage Reset) Yes C
Engine Stall History during Stop&Start (CPU Malfunction) Yes D
Engine Stall History during Stop&Start (CPU Reset Other than Reduced Voltage Reset/CPU Malfunction) Yes




A

3.CHECK VEHICLE CONDITION (COLLISION HISTORY)

B

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST, ST NO. 2 RELAY)

C

11.READ VALUE USING GTS (BATTERY VOLTAGE)

D

3.CHECK VEHICLE CONDITION (COLLISION HISTORY)
a.

Check if the vehicle was in a collision when the engine stalled.

Result:
Result Proceed to
Vehicle was in collision when engine stalled A
Vehicle was not in collision when engine stalled B


HINT:

When "Engine Stall History during Stop&Start (Collision or Battery Voltage Low)" or "Engine Stall History during Engine Starting (Collision)" is stored:

This may have been stored because the vehicle was in a collision or a collision detection signal was input while stop and start control was operating.




A

END (ENGINE STALLED BECAUSE COLLISION DETECTION SIGNAL WAS RECEIVED)

B

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST, ST NO. 2 RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Remove the ST and ST NO. 2 relays from the engine room relay block and junction block assembly.


c.

Disconnect the certification ECU (smart key ECU assembly) connector.


d.

Disconnect the park/neutral position switch assembly connector.


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G313-21 (STA) - ST relay terminal 2 Always Below 1 Ω
G313-23 (STA2) - ST NO. 2 relay terminal 2 Always Below 1 Ω
G313-21 (STA) - Body ground Always 10 kΩ or higher
ST relay terminal 2 - Body ground Always 10 kΩ or higher
G313-23 (STA2) - Body ground Always 10 kΩ or higher
ST NO. 2 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ST, ST NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ST, ST NO. 2 RELAY - BODY GROUND)
a.

Remove the ST and ST NO. 2 relays from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω
ST NO. 2 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ST, ST NO. 2 RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ST, ST NO. 2 RELAY - BATTERY)
a.

Remove the ST and ST NO. 2 relays from the engine room relay block and junction block assembly.


b.
A475031C01
0.365,0.115 0.677,0.313 0.313,0.198 10 false *1 2.635,1.646 2.948,1.844 0.313,0.198 10 false *a 0.198,1.177 0.51,1.375 0.313,0.198 10 false *b
*1 Engine Room Relay Block and Junction Block Assembly
*a ST Relay Terminal
*b ST NO. 2 Relay Terminal


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST relay terminal 5 - Body ground Always 9.5 to 14 V
ST NO. 2 relay terminal 5 - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)
a.
A346341C04
0.448,0.208 0.76,0.406 0.313,0.198 10 false *1 2.531,0.302 2.844,0.5 0.313,0.198 10 false *a
*1 Starter Assembly
*a D13-1 (B)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D13-1 (B) - Body ground Always 9.5 to 14 V


NOTICE:

Before performing this step, check that the starter assembly connector D13 is not disconnected or loose.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ST, ST NO. 2 RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ST, ST NO. 2 RELAY - STARTER ASSEMBLY)
a.

Remove the ST and ST NO. 2 relays from the engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 3 - D14-1 (SL1) Always Below 1 Ω
ST NO. 2 relay terminal 3 - D14-2 (SL2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.INSPECT RELAY (ST, ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT RELAY (ST, ST NO. 2 RELAY)


Result:
Proceed to
OK
NG



OK

10.INSPECT STARTER ASSEMBLY

NG

REPLACE RELAY (ST, ST NO. 2 RELAY)

10.INSPECT STARTER ASSEMBLY

Result:
Proceed to
OK
NG



OK

NG

11.READ VALUE USING GTS (BATTERY VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).

HINT:

Do not start the engine.



c.

Turn the GTS on.


d.

Turn off all electrical systems.


e.

Enter the following menus: Powertrain / Stop and Start / Data List / Battery Voltage.


f.

Read the battery voltage displayed on the GTS screen.

Result:
Result Proceed to
9 to 14 V A
Below 9 V B




A

B

12.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY)
12.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY)
a.

Inspect the No. 1 integration relay (EFI MAIN NO. 1 relay).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/ Urea SCR System)>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BATTERY)

NG

REPLACE NO. 1 INTEGRATION RELAY

13.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BATTERY)
a.

Disconnect the engine stop and start ECU connector.


b.
A348176C23
0.188,0.99 0.563,1.323 0.375,0.333 0.646,1.823 1.198,1.281 true 1.531,1.844 1.25,1.521 true 0.219,0.219 0.531,0.417 0.313,0.198 10 false *a 0.448,1.875 0.76,2.073 0.313,0.198 10 false BIN2 1.469,1.854 1.781,2.052 0.313,0.198 10 false BIN1 0.208,1.073 0.552,1.292 0.344,0.219 10 false G312
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G312-1 (BIN2) - Body ground Always 9.5 to 14 V
G312-3 (BIN1) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G312-2 (GND2) - Body ground Always Below 1 Ω
G312-8 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BATTERY)
a.

Disconnect the engine stop and start ECU connector.


b.

Turn the engine switch on (IG).


c.
A346332C55
1.531,0.417 2.104,0.656 0.573,0.24 0.75,1.167 0.417,1.167 true 1.646,0.458 2.104,0.656 0.458,0.198 10 false G313 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 0.198,1.094 0.51,1.292 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G313-1 (+B) - Body ground Engine switch on (IG) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G313-6 (DGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR