Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0332058 LANE DEPARTURE ALERT SYSTEM J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

The forward recognition camera receives the LDA switch on/off signal from the steering pad switch assembly.

WIRING DIAGRAM

C445050E02
1.458,1.542 2.438,1.854 0.979,0.313 10 false LDA Switch 0.823,1.896 2.865,2.333 2.042,0.438 10 false Steering Pad Switch Assembly 3.01,1.906 4.125,2.438 1.115,0.531 10 false Spiral Cable Sub-assembly 4.906,0.781 6.698,1.021 1.792,0.24 10 false Forward Recognition Camera 2.76,0.396 3.219,0.594 0.458,0.198 10 false z16 3.531,0.292 4.146,0.49 0.615,0.198 10 false DIST 3.542,1.302 4.156,1.5 0.615,0.198 10 false ECC 4.906,0.625 5.292,0.844 0.385,0.219 10 false W22 5.479,0.417 5.979,0.615 0.5,0.198 10 false LKSW 5.26,0.292 5.573,0.49 0.313,0.198 10 false 3 4,0.198 4.313,0.396 0.313,0.198 10 false 12 4.052,1.198 4.365,1.396 0.313,0.198 10 false 2 2.833,1.188 3.146,1.385 0.313,0.198 10 false 7 2.833,0.188 3.146,0.385 0.313,0.198 10 false 4 2.323,0.292 2.938,0.49 0.615,0.198 10 false DIST 2.323,1.292 2.938,1.49 0.615,0.198 10 false ECC 5.208,1.292 5.521,1.49 0.313,0.198 10 false 21 5.49,1.417 5.99,1.615 0.5,0.198 10 false ECCS 5.604,1.802 6.052,2.042 0.448,0.24 10 false G181 5.604,1.979 6.052,2.219 0.448,0.24 10 false ECM 3.906,1.406 4.521,1.604 0.615,0.198 10 false G208 3.906,0.396 4.521,0.594 0.615,0.198 10 false G208 2.75,1.406 3.208,1.604 0.458,0.198 10 false z16 4.875,1.302 5.188,1.5 0.313,0.198 10 false *1 4.75,1.573 5.063,1.771 0.313,0.198 10 false *2 0.26,2.479 2.406,2.677 2.146,0.198 10 false *1: for 2TR-FE 1.604,2.469 3.958,2.729 2.354,0.26 10 false *2: except 2TR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

If the forward recognition camera is replaced with a new one, it is necessary to perform forward recognition camera optical axis adjustment and clear the vehicle control history for each system.

HINT:

Perform forward recognition camera optical axis alignment with either "One time recognition" or "Sequential recognition". Refer to the following for clearing the vehicle control history.

One time recognition:Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential recognition:Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


·

During the steering pad switch assembly check, check the precautions for the airbag system since the horn button assembly is removed during servicing (installation/removal of parts, checks, replacement, etc.)

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS (LDA CONTROL)
a.

Read the Data List according to the display on the GTS.

Chassis > Lane Control > Data List
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
LDA Control Whether lane departure alert system control is permitted or not / Prohibit or Permit Prohibit: Lane departure alert system control not possible
Permit: Lane departure alert system control possible
-


Result:
Result Proceed to
Data List value changes when LDA switch is operated A
Data List value does not change when LDA switch is operated B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY

Click hereSteering>STEERING COLUMN>STEERING WHEEL>INSPECTION

Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the W22 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G208-12 (DIST) - W22-3 (LKSW) Always Below 1 Ω
G208-12 (DIST) or W22-3 (LKSW) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (except 2TR-FE) A
OK (for 2TR-FE) B
NG C



A

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

B

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.
C428780C03
1.5,0.177 1.906,0.438 0.406,0.26 0.844,0.927 0.958,0.927 0.958,0.927 1.344,1.188 true 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 1.531,0.229 2.01,0.458 0.479,0.229 10 false G208 0.521,0.865 0.979,1.063 0.458,0.198 10 false ECC
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G208-2 (ECC) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)
a.

Disconnect the G181 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G208-2 (ECC) - G181-21 (ECCS) Always Below 1 Ω
G208-2 (ECC) or G181-21 (ECCS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR