When the shift lever is in S, the shift range can be changed using the shift paddle switches. It is also possible to select the shift range when the vehicle is being driven with the shift lever in D by operating the shift paddle switches.
Refer to the SRS precaution before troubleshooting.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Sports Shift Up SW | Sport shift up switch status/
ON or OFF |
·
ON: "+" shift paddle operated (up-shift) ·
OFF: "+" shift paddle not operated (up-shift) |
- |
| Sports Shift Down SW | Sport shift down switch status/
ON or OFF |
·
ON: "-" shift paddle operated (down-shift) ·
OFF: "-" shift paddle not operated (down-shift) |
- |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Disconnect the ECM connector.
Disconnect the transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G56-15 (SFTU) - Body ground | "+" shift paddle operated and held (up-shift) | Below 2.5 Ω |
| G56-9 (SFTD) - Body ground | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| G56-15 (SFTU) - Body ground | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| G56-9 (SFTD) - Body ground | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| *a | Rear view of wire harness connector
(to ECM) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the spiral cable sub-assembly connector.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G208-2 (ECC) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the spiral cable sub-assembly connector.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G56-9 (SFTD) - G208-7 (SDN) | Always | Below 1 Ω |
| G56-15 (SFTU) - G208-14 (SUP) | Always | Below 1 Ω |
| G56-9 (SFTD) or G208-7 (SDN) - Body ground | Always | 10 kΩ or higher |
| G56-15 (SFTU) or G208-14 (SUP) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the steering pad switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z16-6 (SUP) - z16-7 (ECC) | "+" shift paddle operated and held (up-shift) | Below 2.5 Ω |
| z16-12 (SDN) - z16-7 (ECC) | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| z16-6 (SUP) - z16-7 (ECC) | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| z16-12 (SDN) - z16-7 (ECC) | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| *a | Steering Pad Switch Assembly Connector
(to Spiral Cable Sub-assembly) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the shift paddle switch LH.
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| SDN - ECC | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| SDN - ECC1 | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| SDN - ECC | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| SDN - ECC1 | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| *1 | Shift Paddle Switch LH |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the shift paddle switch RH.
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| SUP - ECC1 | "+" shift paddle operated and held (up-shift) | Below 2.5 Ω |
| SUP - ECC1 | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| *1 | Shift Paddle Switch RH |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 1 switch wire connector.
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z25-2 (SUP) - z25-7 (ECC) | "+" shift paddle operated and held (up-shift) | Below 2.5 Ω |
| z25-3 (SDN) - z25-7 (ECC) | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| z25-2 (SUP) - z25-7 (ECC) | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| z25-3 (SDN) - z25-7 (ECC) | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| *a | Front view of wire harness connector
(to Steering Pad Switch Assembly) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG