Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P122900  Fuel Pump Valve Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P122900 Fuel Pump Valve Malfunction The actual fuel pressure exceeds the target fuel pressure by 5000 kPag or higher for 30 seconds.
(1 trip detection logic)
·

Short in pre-stroke control valve circuit

·

Fuel supply pump assembly

·

Fuel pressure sensor (common rail assembly)

·

ECM


Comes on DTC stored SAE Code: P1229

Related Data List
DTC No. Data List
P122900
·

Fuel Pressure (High)

·

Target Fuel Pressure (High)



HINT:
·

For more information on the fuel supply pump assembly (pre-stroke control valve) and common rail system, refer to System Description (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).

·

When DTC P122900 is stored, check the internal fuel pressure of the common rail assembly by entering the following menus: Powertrain / Engine / Data List / Fuel Pressure (High), Target Fuel Pressure (High).

Under a stable condition such as idling after warm up the engine, Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) when normal.

·

This DTC is stored when the actual fuel pressure in the common rail assembly is higher than the target fuel pressure, even though a signal is not being output from the ECM to operate the pre-stroke control valve.

This DTC indicates that the pre-stroke control valve may be stuck or have a short circuit.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P122900 Idling for 60 seconds or more

MONITOR DESCRIPTION

This DTC is stored when the actual fuel pressure in the common rail assembly is higher than the target fuel pressure, even though a signal is not being output from the ECM to drive the pre-stroke control valve. This DTC indicates that the pre-stroke control valve may be stuck or have a short circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
DTC P122900 and DTCs related to the fuel pressure sensor circuit* are output B
Except above A


HINT:

*: Fuel pressure sensor circuit DTC: P13A011, P13A015, P13A02A, P13A511, P13A515, P13A52A, P13AA11, P13AA15, P13AA2A, P13B011, P13B015, P13B02A, P13E011, P13E015, P13E511, P13E515.




A

2.READ VALUE USING GTS (FUEL PRESSURE (HIGH) AND TARGET FUEL PRESSURE (HIGH))

B

GO TO FUEL PRESSURE SENSOR CIRCUIT

2.READ VALUE USING GTS (FUEL PRESSURE (HIGH) AND TARGET FUEL PRESSURE (HIGH))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).


e.

Check that the internal fuel pressure of the common rail assembly is within the specification below.

OK:

Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) when engine is idling after warming up the engine.



Result:
Proceed to
OK
NG



OK

NG

3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE PRE-STROKE CONTROL VALVE)
3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE PRE-STROKE CONTROL VALVE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Pre-stroke Control Valve.


d.

Perform the Active Test and check that operation sounds can be heard from the pre-stroke control valve.

HINT:
·

Perform this procedure with the engine stopped and check the operation sounds from outside the vehicle.

·

Check in a quiet location with the hood opened, as the operation sound is difficult to hear.

·

In order to distinguish between the operation sounds of other actuators, check by using the GTS to turn the Active Test open and close several times.



OK:

The operation sound is generated when performing the Active Test, and stops when finished.



Result:
Proceed to
OK
NG



OK

4.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
4.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P122900.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE, increase the idling time.



Result:
Proceed to
NEXT



NEXT

END

6.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
a.

Disconnect the pre-stroke control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r6-1 - C150-3 (PCV+) Always Below 1 Ω
r6-2 - C150-4 (PCV-) Always Below 1 Ω
r6-1 or C150-3 (PCV+) - Body ground and other terminals Always 10 kΩ or higher
r6-2 or C150-4 (PCV-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
10.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).


d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Fuel Pressure (High)) and the actual fuel pressure (Fuel Pressure (High)) when the "Test the Fuel Leak" Active Test is performed.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DATA LIST / ACTIVE TEST

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E76
3.604,2.427 3.719,1.948 3.719,1.948 3.792,1.948 false 4.604,2.583 4.948,2.323 4.948,2.323 5.031,2.323 false 3.438,2.635 3.479,1.833 3.479,1.833 3.427,1.833 false 3.688,3.271 3.563,4.188 3.563,4.188 3.708,4.188 false 0.083,1.417 1.448,1.573 1.365,0.156 10 false Active Test Operation 0.083,0.583 1.479,0.781 1.396,0.198 10 false Engine Speed (rpm) 0.313,3.198 1.854,3.469 1.542,0.271 10 false Fuel Pressure (High) 3.802,1.865 5.74,2.031 1.938,0.167 10 false Target Fuel Pressure (High) 6.469,4.125 6.865,4.302 0.396,0.177 10 false Time 2.115,2.417 2.885,2.99 0.771,0.573 10 false Less than 10000 kPag 3,4.26 3.688,4.427 0.688,0.167 10 false 2 seconds 5.073,2.208 6.583,2.719 1.51,0.51 10 false Abnormal Fuel Pressure (High) 2.677,1.042 3.354,1.24 0.677,0.198 10 false Test Start 4.458,1.042 5.125,1.24 0.667,0.198 10 false Test Stop 5.885,1.042 6.563,1.24 0.677,0.198 10 false Test Start 2.073,1.76 3.427,2.188 1.354,0.427 10 false Normal Fuel Pressure (High) 1.646,0.271 2.021,0.438 0.375,0.167 10 false 2000 1.885,0.833 2.052,1 0.167,0.167 10 false 0 1.75,1.302 2.073,1.469 0.323,0.167 10 false ON 1.698,1.552 2.021,1.719 0.323,0.167 10 false OFF 3.771,4.125 5.969,4.677 2.198,0.552 10 false Pressure Discharge Valve Abnormal Fuel Pressure (High)

Standard:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPag.


HINT:
·

"Target Fuel Pressure (High)" is the target fuel pressure controlled by the ECM.

·

"Fuel Pressure (High)" is the actual fuel pressure.



Result:
Result Proceed to
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPag. B
Except above A




A

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY

B

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED