Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY › from 2020.08
RM27T0E _52 Drivetrain _053705 AXLE AND DIFFERENTIAL _0260863 FRONT DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front differential carrier assembly removal/installation are shown below.

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Correction of steering angle neutral point Multi-terrain monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane departure alert system Drive the vehicle straight ahead at 40 km/h (25 mph) or more for 10 seconds or more. (Click here)
Pre-collision system
Lighting system (EXT) (for LED Headlight)
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Vehicle stability control system (for Hydraulic brake booster) Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds. (Click here)



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 3.REMOVE FRONT WHEELS

Hide 51405A 4.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 5.REMOVE TRANSMISSION UNDER COVER (except 5L-E)

Hide 51450 6.REMOVE REAR ENGINE UNDER COVER ASSEMBLY (except 5L-E)

Hide 37140 8.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 43420 9.REMOVE FRONT DRIVE SHAFT ASSEMBLY

Hide 48810 10.REMOVE FRONT STABILIZER LINK ASSEMBLY

a.

w/ KDSS:

Remove the stabilizer link (See page Suspension>FRONT SUSPENSION>FRONT STABILIZER BAR (w/ KDSS)>REMOVAL).


b.

w/o KDSS:

Remove the stabilizer link (See page Suspension>FRONT SUSPENSION>FRONT STABILIZER BAR (w/o KDSS)>REMOVAL).


Hide 89543 11.REMOVE FRONT SPEED SENSOR

Hide 45047 12.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

a.

Disconnect the tie rod end sub-assembly (See page Steering>STEERING GEAR / LINKAGE>STEERING GEAR>REMOVAL).


Hide 45046 13.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

a.

Disconnect the tie rod end sub-assembly (See page Steering>STEERING GEAR / LINKAGE>STEERING GEAR>REMOVAL).


Hide 48069 14.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Remove the front lower No. 1 suspension arm sub-assembly (See page Suspension>FRONT SUSPENSION>FRONT LOWER SUSPENSION ARM>REMOVAL).


Hide 48068 15.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 41110F 16.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY

C097020E10
1.313,0.188 1.5,0.344 0.188,0.156 10 true *1 1.99,0.188 2.177,0.344 0.188,0.156 10 true *1 1.844,1.49 2.031,1.646 0.188,0.156 10 true *2

a.

Remove the bolt and disconnect the front differential breather tube bracket.


b.

Support the front differential with a jack.


c.

Remove the front No. 1 differential mounting nut.


d.

Remove the 2 front mounting bolts and nut.

Text in Illustration
*1 Mounting Bolt
*2 Mounting Nut


e.

Disconnect the actuator hose and connector.


f.

Lower the jack and remove the front differential.


g.
B084273

Remove the 3 bolts and front No. 1 differential support.


h.
B084274

Remove the 2 bolts and front No. 2 differential support.


i.
B084275

Remove the 2 bolts and front No. 3 differential support.