Cruise Control Switch Circuit
Circuit diagnosis · Vehicles built from Jan 2012
DESCRIPTION
The cruise control main switch is used to operate 8 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCELERATION), TAP-UP, CANCEL and MODE. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCELERATION) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in each arrow direction and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the resistance value that has been changed by the switch operation to control MODE, SET, - (COAST), RES (RESUME), + (ACCELERATION) and CANCEL. The dynamic radar cruise control system has two cruise control modes: the constant speed control mode and vehicle-to-vehicle distance control mode.- HINT:
- The vehicle-to-vehicle distance control mode is always selected when starting up the dynamic radar cruise control system.
- The operation of the constant speed control mode is the same as the cruise control system.
- The vehicle-to-vehicle distance control mode is always selected when starting up the dynamic radar cruise control system.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH) |
![]() ![]() |
Using the intelligent tester, read the Data List (Click here).
Radar Cruise Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
CCS Main SW M-CPU
Cruise control main switch (Main CPU) / ON or OFF
ON: Cruise control main switch (Main CPU) on
OFF: Cruise control main switch (Main CPU) off
-
Cancel Switch
CANCEL switch signal / ON or OFF
ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch
-SET switch signal / ON or OFF
ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch
+RES switch signal / ON or OFF
ON: +RES switch on
OFF: +RES switch off
-
CCS Main SW S-CPU
Cruise control main switch (Sub CPU) / ON or OFF
ON: Cruise control main switch (Sub CPU) on
OFF: Cruise control main switch (Sub CPU) off
-
- OK:
- The intelligent tester display changes according to operation of cruise control main switch.
|
|
||||
| OK | ||
| ||
| 2. INSPECT CRUISE CONTROL MAIN SWITCH |


Remove the cruise control main switch (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 (ECC) - 3 (CCS)
Neutral
1 MΩ or higher
Pushed to +RES
235 to 245 Ω
Pushed to -SET
620 to 640 Ω
Pushed to CANCEL
1510 to 1570 Ω
Main switch pushed off
1 MΩ or higher
Main switch pushed on
Below 2.5 Ω
1 (ECC) - 2 (R/N)
MODE switch pushed on
Below 2.5 Ω
MODE switch off
1 MΩ or higher
|
|
||||
| OK | |
| 3. INSPECT CRUISE CONTROL SWITCH WIRE |
![]() ![]() |
Remove the cruise control switch wire.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z37-3 - 3
Always
Below 1 Ω
z37-1 - 2
z37-4 - 1
z37-3 - Body ground
Always
10 kΩ or higher
z37-1 - Body ground
z37-4 - Body ground
|
|
||||
| OK | |
| 4. INSPECT SPIRAL CABLE |
![]() ![]() |
Check the spiral cable and connector for scratches, cracks, dents and chips. If any defects are found, replace the spiral cable with a new one.
Check the spiral cable.
Set the spiral cable to the center position (Click here).
After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z37-3 - E12-1 (CCS)
Always
Below 1 Ω
z37-1 - E12-7 (R/N)
z37-4 - E12-2 (ECC)
After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise. Then while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
- NOTICE:
- As the spiral cable may break, do not rotate the spiral cable more than the specified amount.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z37-3 - E12-1 (CCS)
Always
Below 1 Ω
z37-1 - E12-7 (R/N)
z37-4 - E12-2 (ECC)
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND) |
![]() ![]() |
Disconnect the E12 spiral cable connector.
Disconnect the A38*1 or A52*2 ECM connector.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
E12-1 (CCS) - A38-45 (CCS)
Always
Below 1 Ω
E12-7 (R/N) - A38-37 (CCHG)
E12-1 (CCS) - Body ground
Always
10 kΩ or higher
E12-7 (R/N) - Body ground
E12-2 (ECC) - Body ground
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
E12-1 (CCS) - A52-45 (CCS)
Always
Below 1 Ω
E12-7 (R/N) - A52-37 (CCHG)
E12-1 (CCS) - Body ground
Always
10 kΩ or higher
E12-7 (R/N) - Body ground
E12-2 (ECC) - Body ground
Always
Below 1 Ω
| Result |
Proceed to |
| OK (for 1UR-FE) |
A |
| OK (for 3UR-FE) |
B |
| NG |
C |
|
|
||||
|
|
||||
| A | ||
| ||




