2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

Black Smoke Emitted

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing a fuel supply pump, the ECM needs initialization (Click here).
  3. After replacing a fuel injector, the ECM needs registration (Click here).

HINT:
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle to be normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


1. READ OUTPUT DTC (RELATED TO ENGINE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTCs related to the engine are output
    B



B
REPAIR OR REPLACE ENGINE CONTROL SYSTEM ACCORDING TO DTC OUTPUT (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #8)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List.

  1. Select the following menu items in order and read the values.

    1. Injection Volume
    2. Injection Feedback Val #1, #2, #3, #4, #5, #6, #7 and #8

    Standard Value:
    Item
    Engine Speed*
    Reference Value
    Injection Volume
    Idling (No engine load)
    3.0 to 10 mm3/st
    Injection Feedback Val #1 to #8
    Idling (No engine load)
    -3.0 to 3.0 mm3/st

    HINT:
    *: If no idling conditions are specified, the shift lever should be in N, and the A/C switch and all accessory switches should be off.



NG
Go to step 11
OK


3. PERFORM ENGINE SPEED ACCELERATION

HINT:
If the exhaust gas contains excessive black smoke, perform the following operations.

  1. Accelerate the engine to the maximum speed with no load 20 times.

  1. Check the volume of black smoke in the exhaust gas.

    Result 
    Result
    Proceed to
    Black smoke is not present
    OK
    Black smoke remains in the exhaust gas
    NG

    HINT:
    Soot deposits in the exhaust system may cause excessive black smoke.



NG
Go to step 4
OK

END

4. CHECK INTAKE AIR CONTROL SYSTEM AND EXHAUST SYSTEM
  1. Inspect the engine condition (Click here).



NG
REPAIR OR REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST
OK


5. INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


6. CHECK TURBOCHARGING PRESSURE
  1. Check the turbocharging pressure (Click here).

    OK:
    The turbocharger pressure is within the standard range.



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 or Bank 2) (Click here)
OK


7. READ VALUE USING INTELLIGENT TESTER (DATA LIST)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List.

  1. Select the following menu items in order and read the values.

    1. Fuel Press
    2. Injection Volume
    3. Main Injection Period
    4. Pilot 2 Injection Period
    5. Injection Feedback Val #1, #2, #3, #4, #5, #6, #7 and #8

    Reference:
    Item
    Engine Speed*
    Reference Value
    Fuel Press
    Idling
    27 to 37 MPa
    Fuel Press
    2000 rpm (no engine load)
    50 to 70 MPa
    Fuel Press
    3000 rpm (no engine load)
    52 to 76 MPa
    Injection Volume
    Idling
    3.0 to 10 mm3/st
    Injection Volume
    2000 rpm (no engine load)
    3.5 to 11 mm3/st
    Injection Volume
    3000 rpm (no engine load)
    6.5 to 13 mm3/st
    Main Injection Period
    Idling
    430 to 730 μs
    Pilot 2 Injection Period
    Idling
    390 to 490 μs
    Injection Feedback Val #1 to #8
    Idling
    -3.0 to 3.0 mm3

    HINT:
    *: If no idling conditions are specified, the shift lever should be in N, and the A/C switch and all accessory switches should be off.

    Result 
    Result
    Proceed to
    Within reference value
    A
    One of Injection Feedback Val #1 to #8 is not within reference value
    B
    Other result
    C



B
REPLACE MALFUNCTIONING FUEL INJECTOR (Click here)

C
Go to step 11
A


8. CHECK CYLINDER COMPRESSION PRESSURE
  1. Check the cylinder compression pressure (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


9. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - EDU)
A182481E01
A182481E02
  1. Disconnect the fuel injector connectors.

  1. Disconnect the No. 1 EDU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    No. 1 
    Tester Connection
    Condition
    Specified Condition
    C5-2 - C74-4 (INJ1)
    Always
    Below 1 Ω
    C14-2 - C74-3 (INJ4)
    Always
    Below 1 Ω
    C69-2 - C74-2 (INJ6)
    Always
    Below 1 Ω
    C68-2 - C74-1 (INJ7)
    Always
    Below 1 Ω
    C5-1 - C74-5 (COM1)
    Always
    Below 1 Ω
    C14-1 - C74-5 (COM1)
    Always
    Below 1 Ω
    C69-1 - C74-6 (COM2)
    Always
    Below 1 Ω
    C68-1 - C74-6 (COM2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    No. 1 
    Tester Connection
    Condition
    Specified Condition
    C5-2 or C74-4 (INJ1) - Body ground
    Always
    10 kΩ or higher
    C14-2 or C74-3 (INJ4) - Body ground
    Always
    10 kΩ or higher
    C69-2 or C74-2 (INJ6) - Body ground
    Always
    10 kΩ or higher
    C68-2 or C74-1 (INJ7) - Body ground
    Always
    10 kΩ or higher
    C5-1 or C74-5 (COM1) - Body ground
    Always
    10 kΩ or higher
    C14-1 or C74-5 (COM1) - Body ground
    Always
    10 kΩ or higher
    C69-1 or C74-6 (COM2) - Body ground
    Always
    10 kΩ or higher
    C68-1 or C74-6 (COM2) - Body ground
    Always
    10 kΩ or higher

  1. Disconnect the fuel injector connectors.

  1. Disconnect the No. 2 EDU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    No. 2 
    Tester Connection
    Condition
    Specified Condition
    C70-2 - C76-4 (INJ2)
    Always
    Below 1 Ω
    C9-2 - C76-3 (INJ5)
    Always
    Below 1 Ω
    C67-2 - C76-1 (INJ3)
    Always
    Below 1 Ω
    C54-2 - C76-2 (INJ8)
    Always
    Below 1 Ω
    C70-1 - C76-5 (COM4)
    Always
    Below 1 Ω
    C9-1 - C76-5 (COM4)
    Always
    Below 1 Ω
    C67-1 - C76-6 (COM5)
    Always
    Below 1 Ω
    C54-1 - C76-6 (COM5)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    No. 2 
    Tester Connection
    Condition
    Specified Condition
    C70-2 or C76-4 (INJ2) - Body ground
    Always
    10 kΩ or higher
    C9-2 or C76-3 (INJ5) - Body ground
    Always
    10 kΩ or higher
    C67-2 or C76-1 (INJ3) - Body ground
    Always
    10 kΩ or higher
    C54-2 or C76-2 (INJ8) - Body ground
    Always
    10 kΩ or higher
    C70-1 or C76-5 (COM4) - Body ground
    Always
    10 kΩ or higher
    C9-1 or C76-5 (COM4) - Body ground
    Always
    10 kΩ or higher
    C67-1 or C76-6 (COM5) - Body ground
    Always
    10 kΩ or higher
    C54-1 or C76-6 (COM5) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER FUEL CUT)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Cylinder #1, #2, #3, #4, #5, #6, #7 and #8 Fuel Cut.

  1. Check the engine idling condition while the fuel injection of each cylinder is cut using the tester.

    Result 
    Engine Idling Condition
    Proceed to
    Becomes unstable
    A
    Does not change
    B

    HINT:
    Replace the fuel injector mounted on the cylinder that causes no significant idle speed change.



B
REPLACE MALFUNCTIONING FUEL INJECTOR (Click here)
A

REPLACE INJECTOR DRIVER (No. 1 and/or No. 2) (Click here)

11. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

  1. Read the value.

    Standard Value:
    Item
    Inspection Condition
    Reference Value
    Coolant Temp
    Idling with warm engine (A/C switch off)
    75 to 90°C (167 to 194°F)



NG
Go to step 17
OK


12. READ VALUE USING INTELLIGENT TESTER (MAP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine / Data List / MAP.

  1. Read the value.

    OK:
    Same value as the actual atmospheric pressure.



NG
Go to step 18
OK


13. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

  1. Read the value.

    Standard Value:
    Item
    Inspection Condition
    Reference Value
    Engine Speed
    Idling with warm engine (A/C switch off)
    1. 500 to 600 rpm (M/T)
    2. 550 to 650 rpm (A/T)



NG
Go to step 19
OK


14. READ VALUE USING INTELLIGENT TESTER (ACCEL SENS. NO.# VOLT %)

  1. C129061E02
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

  1. Read the values.

    Standard:
    Accelerator Pedal
    Accel Sens. No.1 Volt %
    Accel Sens. No.2 Volt %
    Released
    10 to 22%
    24 to 40%
    Depressed
    52 to 90%
    68 to 99%



NG
Go to step 20
OK


15. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Inlet Air.

  1. Read the value.

    OK:
    Same as air temperature near intake manifold.



NG
Go to step 21
OK


16. READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine / Data List / Fuel Press.

  1. Read the value.

    Standard Value:
    Item
    Inspection Condition
    Reference Value
    Fuel Press
    Idling
    27 to 37 MPa



NG
Go to step 22
OK

REPLACE ECM (Click here)

17. INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

18. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

  1. A182383E01
    Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C80-2 (PIM) - C45-114 (PIM)
    Always
    Below 1 Ω
    C80-3 (VC) - C45-66 (VCPM)
    Always
    Below 1 Ω
    C80-1 (E) - C45-75 (E2)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C80-2 (PIM) - C46-114 (PIM)
    Always
    Below 1 Ω
    C80-3 (VC) - C46-66 (VCPM)
    Always
    Below 1 Ω
    C80-1 (E) - C46-75 (E2)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C80-2 (PIM) or C45-114 (PIM)) - Body ground
    Always
    10 kΩ or higher
    C80-3 (VC) or C45-66 (VCPM) - Body ground
    Always
    10 kΩ or higher
    C80-1 (E) or C45-75 (E2) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C80-2 (PIM) or C46-114 (PIM)) - Body ground
    Always
    10 kΩ or higher
    C80-3 (VC) or C46-66 (VCPM) - Body ground
    Always
    10 kΩ or higher
    C80-1 (E) or C46-75 (E2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR (Click here)

19. INSPECT CRANKSHAFT POSITION SENSOR

  1. A165740E01
    Disconnect the crankshaft position sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (NE+) - 2 (NE-)
    Cold
    1630 to 2740 Ω
    1 (NE+) - 2 (NE-)
    Hot
    2065 to 3225 Ω

    HINT:
    In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

20. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

  1. A115665E35
    Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A31-1 (VCP2) - A38-56 (VCP2)
    Always
    Below 1 Ω
    A31-2 (EPA2) - A38-58 (EPA2)
    Always
    Below 1 Ω
    A31-3 (VPA2) - A38-54 (VPA2)
    Always
    Below 1 Ω
    A31-4 (VCPA) - A38-55 (VCPA)
    Always
    Below 1 Ω
    A31-5 (EPA) - A38-57 (EPA)
    Always
    Below 1 Ω
    A31-6 (VPA) - A38-53 (VPA)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    A31-1 (VCP2) - A52-56 (VCP2)
    Always
    Below 1 Ω
    A31-2 (EPA2) - A52-58 (EPA2)
    Always
    Below 1 Ω
    A31-3 (VPA2) - A52-54 (VPA2)
    Always
    Below 1 Ω
    A31-4 (VCPA) - A52-55 (VCPA)
    Always
    Below 1 Ω
    A31-5 (EPA) - A52-57 (EPA)
    Always
    Below 1 Ω
    A31-6 (VPA) - A52-53 (VPA)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A31-1 (VCP2) or A38-56 (VCP2) - Body ground
    Always
    10 kΩ or higher
    A31-2 (EPA2) or A38-58 (EPA2) - Body ground
    Always
    10 kΩ or higher
    A31-3 (VPA2) or A38-54 (VPA2) - Body ground
    Always
    10 kΩ or higher
    A31-4 (VCPA) or A38-55 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A31-5 (EPA) or A38-57 (EPA) - Body ground
    Always
    10 kΩ or higher
    A31-6 (VPA) or A38-53 (VPA) - Body ground
    Always
    10 kΩ or higher
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A31-1 (VCP2) or A52-56 (VCP2) - Body ground
    Always
    10 kΩ or higher
    A31-2 (EPA2) or A52-58 (EPA2) - Body ground
    Always
    10 kΩ or higher
    A31-3 (VPA2) or A52-54 (VPA2) - Body ground
    Always
    10 kΩ or higher
    A31-4 (VCPA) or A52-55 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A31-5 (EPA) or A52-57 (EPA) - Body ground
    Always
    10 kΩ or higher
    A31-6 (VPA) or A52-53 (VPA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY (ACCELERATOR PEDAL POSITION SENSOR) (Click here)

21. INSPECT INTAKE AIR TEMPERATURE SENSOR

  1. Remove the mass air flow meter (Click here).A168114E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 - 5
    -20°C (-4°F)
    13.6 to 18.4 kΩ
    20°C (68°F)
    2.21 to 2.69 kΩ
    60°C (140°F)
    0.49 to 0.67 kΩ



NG
REPLACE MASS AIR FLOW METER (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

22. INSPECT COMMON RAIL (for Bank 1) (FUEL PRESSURE SENSOR)
  1. Inspect the fuel pressure sensor (Click here).



NG
REPLACE COMMON RAIL (for Bank 1) (Click here)
OK


23. CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

  1. A182377E01
    Disconnect the fuel pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C82-2 (PR) - C45-69 (PCR1)
    Always
    Below 1 Ω
    C82-3 (VC) - C45-70 (VCM)
    Always
    Below 1 Ω
    C82-1 (E2) - C45-75 (E2)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C82-2 (PR) - C46-69 (PCR1)
    Always
    Below 1 Ω
    C82-3 (VC) - C46-70 (VCM)
    Always
    Below 1 Ω
    C82-1 (E2) - C46-75 (E2)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C82-2 (PR) or C45-69 (PCR1) - Body ground
    Always
    10 kΩ or higher
    C82-3 (VC) or C45-70 (VCM) - Body ground
    Always
    10 kΩ or higher
    C82-1 (E2) or C45-75 (E2) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C82-2 (PR) or C46-69 (PCR1) - Body ground
    Always
    10 kΩ or higher
    C82-3 (VC) or C46-70 (VCM) - Body ground
    Always
    10 kΩ or higher
    C82-1 (E2) or C46-75 (E2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


24. REPLACE ECM
  1. Replace the ECM (Click here).

    NOTICE:
    After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

  1. Check if the engine starts smoothly or if the engine stalls.

    OK:
    The engine starts smoothly and does not stall.



NG
REPLACE FUEL SUPPLY PUMP (Click here)
OK

END


← Engine Difficult to Start or Stalling (from Jan 2012)Black Smoke Emitted (from Jan 2012) →