P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Also covers:
- P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)
- P0051 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)
- P0052 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)
CAUTION / NOTICE / HINT
DESCRIPTION
Refer to DTC P2195 (Click here).- HINT:
- Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
- Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
- When one of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the engine switch is turned off.
- The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the +B side of the circuit.


- Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0031 P0051 |
The Air-Fuel Ratio (A/F) sensor heater current is below 0.8 A (1 trip detection logic). |
|
| P0032 P0052 |
An Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic). |
|
- HINT:
- Bank 1 refers to the bank that includes the No. 1 cylinder.
- Bank 2 refers to the bank that does not include the No. 1 cylinder.
- Sensor 1 refers to the sensor closest to the engine assembly.
- Sensor 2 refers to the sensor farthest away from the engine assembly.
- Bank 1 refers to the bank that includes the No. 1 cylinder.
MONITOR DESCRIPTION
The ECM uses information from the Air-Fuel Ratio (A/F) sensor to regulate the air-fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-Way Catalytic Converter (TWC) to purify the exhaust gases.The A/F sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The A/F sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the A/F sensor becomes inaccurate. As a result, the ECM is unable to regulate air-fuel ratio properly.
When the current in the A/F sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.
Example:
The ECM stores DTC P0032 or P0052 when the current in the A/F sensor heater is higher than 10 A. Conversely, when the heater current is below 0.8 A, DTC P0031 or P0051 is stored.
WIRING DIAGRAM
Refer to DTC P2195 (Click here).INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() ![]() |
Disconnect the Air-Fuel Ratio (A/F) sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 (HA1A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω
1 (HA1A) - 4 (A1A-)
Always
10 kΩ or higher
1 (HA2A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω
1 (HA2A) - 4 (A2A-)
Always
10 kΩ or higher
|
|
||||
| OK | |
| 2. CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR) |
![]() ![]() |
Disconnect the A/F sensor connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C22-2 (+B) - Body ground
Engine switch on (IG)
11 to 14 V
C23-2 (+B) - Body ground
Engine switch on (IG)
11 to 14 V
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 3. INSPECT INTEGRATION RELAY (A/F) |
![]() ![]() |
Remove the integration relay from the engine room relay block.
Inspect the A/F fuse.
Remove the A/F fuse from the integration relay.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A/F fuse
Always
Below 1 Ω
Reinstall the A/F fuse.
Inspect the integration relay (A/F).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1C-1 - 1A-4
Battery voltage not applied to terminals 1A-2 and 1A-3
10 kΩ or higher
Battery voltage applied to terminals 1A-2 and 1A-3
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - A/F SENSOR AND BODY GROUND) |
![]() ![]() |
Disconnect the A/F sensor connector.
Remove the integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
C22-2 (+B) - 1A-4
Always
Below 1 Ω
C23-2 (+B) - 1A-4
Always
Below 1 Ω
1A-2 - 1B-5
Always
Below 1 Ω
1A-3 - Body ground
Always
Below 1 Ω
C22-2 (+B) or 1A-4 - Body ground
Always
10 kΩ or higher
C23-2 (+B) or 1A-4 - Body ground
Always
10 kΩ or higher
1A-2 or 1B-5 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() ![]() |
Disconnect the A/F sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (for LHD):
Tester Connection
Condition
Specified Condition
C22-1 (HA1A) - C45-22 (HA1A)
Always
Below 1 Ω
C23-1 (HA2A) - C45-20 (HA2A)
Always
Below 1 Ω
C22-1 (HA1A) or C45-22 (HA1A) - Body ground
Always
10 kΩ or higher
C23-1 (HA2A) or C45-20 (HA2A) - Body ground
Always
10 kΩ or higher
- Standard Resistance (for RHD):
Tester Connection
Condition
Specified Condition
C22-1 (HA1A) - C46-22 (HA1A)
Always
Below 1 Ω
C23-1 (HA2A) - C46-20 (HA2A)
Always
Below 1 Ω
C22-1 (HA1A) or C46-22 (HA1A) - Body ground
Always
10 kΩ or higher
C23-1 (HA2A) or C46-20 (HA2A) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 1 minute or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
Result Result
Proceed to
No DTC is output
A
P0031, P0032, P0051 or P0052 is output
B
|
|
||||
| A | ||
| ||





