2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the camshaft and camshaft oil control valve, and operating the camshaft timing gear; and 2) changing the relative positions of the gaps between the camshaft and crankshaft.
DTC Code
DTC Detection Condition
Trouble Area
P0016
Deviation in the crankshaft position sensor signal and VVT sensor 1 (for intake side of bank 1) signal (2 trip detection logic).
  1. Mechanical system (Timing belt has jumped tooth or belt stretched)
  2. Oil control valve
  3. Camshaft timing tube
  4. ECM
P0018
Deviation in the crankshaft position sensor signal and VVT sensor 2 (for intake side of bank 2) signal (2 trip detection logic).
  1. Mechanical system (Timing belt has jumped tooth or belt stretched)
  2. Oil control valve
  3. Camshaft timing tube
  4. ECM

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0016 (for bank 1) or P0018 (for bank 2).

WIRING DIAGRAM

Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 OR P0018)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0016 or P0018 is output
    A
    P0016 or P0018 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV)

HINT:
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2) / All Data / VVT Change Angle (Bank 1) or VVT Change Angle (Bank 2).

  1. Perform the Active Test. Check that the displacement angle varies.

    OK:
    Varies.



NG
Go to step 4
OK


3. CHECK VALVE TIMING
A178910E01
  1. Remove the drive belt (Click here).

  1. Remove the timing belt cover LH and RH (Click here).

  1. Turn the crankshaft to align the matchmarks of the crankshaft.

  1. Align the notch of the crankshaft pulley with the "0" position.

  1. Confirm whether the matchmarks of the camshaft pulley and cylinder head cover are facing each other.

  1. If the matchmarks are not facing each other, turn the crankshaft clockwise by 360°. Confirm again if the matchmarks are facing each other.

    OK:
    The matchmarks of the camshaft pulley and the cylinder head cover face each other when the notch of the crankshaft pulley is in the "0" position.



NEXT
Go to step 6
4. INSPECT CAMSHAFT OIL CONTROL VALVE
A160397E02
A182939E01
  1. Remove the OCV.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

  1. Apply positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.



NG
REPLACE CAMSHAFT OIL CONTROL VALVE (Click here)
OK


5. REPLACE CAMSHAFT TIMING TUBE ASSEMBLY
  1. Replace the camshaft timing tube assembly.

    HINT:
    1. P0016 is output, replace the camshaft timing tube assembly for bank 1 (Click here).
    2. P0018 is output, replace the camshaft timing tube assembly for bank 2 (Click here).


NEXT


6. CONFIRM WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Clear the DTC (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester (Click here).

  1. Drive the vehicle in an urban area for approximately 10 minutes.

  1. Read DTCs using the tester.

    OK:
    No DTC is output.



NG
GO TO DTC CHART (Click here)
OK

END


← P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (+ P0012, P0021, P0022) (Sep 2011 – Dec 2011)P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) (+ P0032, P0051, P0052) (Sep 2011 – Dec 2011) →