B2417 Headlight Beam Level Control Motor LH Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- B2418 Headlight Beam Level Control Motor RH Malfunction
DESCRIPTION
The headlight leveling motor receives a signal from the headlight swivel ECU to operate. The headlight swivel ECU receives a signal indicating the operating conditions of the headlight leveling motor.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2417 |
|
|
| B2418 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- After replacing the headlight swivel ECU, initialization of the ECU is necessary (except w/ Dynamic Headlight Auto Leveling) (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B2417 or B2418 output does not occur.
|
|
||||
| OK | ||
| ||
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT LEVELING MOTOR) |
Using the intelligent tester, perform the Active Test (Click here).
AFS Tester Display
Test Part
Control Range
Diagnostic Note
Drive The Leveling Motor UP*
Headlight leveling motor upward operation
ON/OFF
ON: Move up
OFF: Stop
Drive The Leveling Motor DOWN*
Headlight leveling motor downward operation
ON/OFF
ON: Move down
OFF: Stop
- *: Perform the Active Test with the engine running and vehicle stopped.
- OK:
- Headlight leveling motors operate normally.
- *: Perform the Active Test with the engine running and vehicle stopped.
|
|
||||
| OK | |
| 3. CHECK HEADLIGHT LEVELING MOTOR |
Temporarily replace the headlight leveling motor with a new or normally functioning one (Click here).
Check for DTCs (Click here).
- OK:
- DTC B2417 or B2418 output does not occur.
Result Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND) |
Disconnect the headlight swivel ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E101-15 (IG) - Body ground
Ignition switch ON
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E101-22 (E1) - Body ground
Always
Below 1 Ω
| *a |
Front view of wire harness connector (to Headlight Swivel ECU Assembly) |
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - HEADLIGHT UNIT ASSEMBLY) |
Disconnect the E101 headlight swivel ECU connector.
Disconnect the A54*1 or A58*2 headlight unit connector.
- *1: for LH
- *2: for RH
- *1: for LH
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LH:
Tester Connection
Condition
Specified Condition
E101-3 (LHT) - A54-8 (LHIG)
Always
Below 1 Ω
E101-30 (LH+) - A54-3 (LH T)
Always
Below 1 Ω
E101-27 (LH-) - A54-4 (LH E)
Always
Below 1 Ω
E101-3 (LHT) - Body ground
Always
10 kΩ or higher
E101-30 (LH+) - Body ground
Always
10 kΩ or higher
E101-27 (LH-) - Body ground
Always
10 kΩ or higher
- for RH:
Tester Connection
Condition
Specified Condition
E101-4 (RHT) - A58-8 (RHIG)
Always
Below 1 Ω
E101-11 (RH+) - A58-3 (RH T)
Always
Below 1 Ω
E101-28 (RH-) - A58-4 (RH E)
Always
Below 1 Ω
E101-4 (RHT) - Body ground
Always
10 kΩ or higher
E101-11 (RH+) - Body ground
Always
10 kΩ or higher
E101-28 (RH-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT HEADLIGHT UNIT ASSEMBLY |
Remove the headlight unit (Click here).


Text in Illustration *a
Component without harness connected
(Headlight Unit Assembly LH)
*b
Component without harness connected
(Headlight Unit Assembly RH)
*c
Front view of wire harness connector
(to Headlight Leveling Motor LH)
*d
Front view of wire harness connector
(to Headlight Leveling Motor RH)
Disconnect the headlight leveling motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LH:
Tester Connection
Condition
Specified Condition
8 (LHIG) - 3
Always
Below 1 Ω
3 (LH T) - 2
4 (LH E) - 1
- for RH:
Tester Connection
Condition
Specified Condition
8 (RHIG) - 3
Always
Below 1 Ω
3 (RH T) - 2
4 (RH E) - 1
|
|
||||
| OK | |
| 7. CHECK HEADLIGHT LEVELING MOTOR |
Temporarily replace the headlight leveling motor with a new or normally functioning one (Click here).
Check for DTCs (Click here).
- OK:
- DTC B2417 or B2418 output does not occur.
Result Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
