B2416 Height Control Sensor Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- B241A Rear Height Control Sensor
DESCRIPTION
The DTC is stored when the headlight swivel ECU*1 or headlight leveling ECU*2 detects malfunctions in the rear height control sensor LH power source or rear height control sensor LH (w/o Active Height Control Suspension).- *1: w/ Dynamic Headlight Auto Leveling
- *2: w/ Static Headlight Auto Leveling
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2416 |
w/o Active Height Control Suspension:
|
|
w/ Active Height Control Suspension:
| ||
| B241A |
|
WIRING DIAGRAM






INSPECTION PROCEDURE
- NOTICE:
- After replacing the headlight leveling ECU*1 or headlight swivel ECU*2 and rear height control sensor LH, initialization of the ECU is necessary (except w/ Dynamic Headlight Auto Leveling) (Click here).
- *1: w/ Static Headlight Auto Leveling
- *2: w/ Dynamic Headlight Auto Leveling
- *1: w/ Static Headlight Auto Leveling
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B2416 or B241A output does not occur.
|
|
||||
| OK | ||
| ||
| 2. CHECK VEHICLE TYPE |
Check the vehicle type.
Result Result
Proceed to
w/ Static Headlight Auto Leveling
A
w/ Dynamic Headlight Auto Leveling, w/o Active Height Control Suspension
B
w/ Dynamic Headlight Auto Leveling, w/ Active Height Control Suspension
C
|
|
||||
|
|
||||
| A | |
| 3. READ VALUE USING INTELLIGENT TESTER (REAR HEIGHT CONTROL SENSOR) |
Using the intelligent tester, read the Data List (Click here).
HL Auto Leveling Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Height Sens Pw Supply Val
Rear height control sensor power supply value / 0 to 5 V
4.7 to 5.2 V
-
Rr Height Sens Signal Val
Rear height control sensor signal value / 0 to 5 V
Approximately 2.5 V (When vehicle level)
The value changes according to the vehicle height.
- OK:
- Normal conditions listed above are displayed.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH) |
Disconnect the E109 headlight leveling ECU connector.
Disconnect the N7 rear height control sensor LH connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E109-12 (SBR) - N7-1 (SHB)
Always
Below 1 Ω
E109-19 (SHRL) - N7-2 (SHRL)
Always
Below 1 Ω
E109-21 (SGR) - N7-3 (SHG)
Always
Below 1 Ω
E109-12 (SBR) - Body ground
Always
10 kΩ or higher
E109-19 (SHRL) - Body ground
Always
10 kΩ or higher
E109-21 (SGR) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH |
Remove the rear height control sensor LH (Click here).
Inspect the rear height control sensor LH (Click here).
|
|
||||
| OK | ||
| ||
| 6. READ VALUE USING INTELLIGENT TESTER (REAR HEIGHT CONTROL SENSOR) |
Using the intelligent tester, read the Data List (Click here).
AFS Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Height Sens Pw Supply Val
Height control sensor power supply value / 0 to 6.25 V
4.7 to 5.2 V
-
Rr Height Sens Signal Val
Rear height control sensor signal value / 0 to 5 V
Approximately 2.5 V (When vehicle level)
The value changes according to the vehicle height.
- OK:
- Normal conditions listed above are displayed.
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH) |
Disconnect the E101 headlight swivel ECU connector.
Disconnect the N7 rear height control sensor LH connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E101-18 (SBR) - N7-1 (SHB)
Always
Below 1 Ω
E101-19 (SHRL) - N7-2 (SHRL)
Always
Below 1 Ω
E109-21 (SGR) - N7-3 (SHG)
Always
Below 1 Ω
E101-18 (SBR) - Body ground
Always
10 kΩ or higher
E101-19 (SHRL) - Body ground
Always
10 kΩ or higher
E109-21 (SGR) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 8. INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH |
Remove the rear height control sensor LH (Click here).
Inspect the rear height control sensor LH (Click here).
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 9. CHECK FOR DTC (ACTIVE HEIGHT CONTROL SUSPENSION) |
Check for DTCs (Click here).
- OK:
- DTC "C1712 Front Height Control Sensor LH Circuit Malfunction" and "C1714 Rear Height Control Sensor LH Circuit Malfunction" output does not occur.
|
|
||||
| OK | |
| 10. READ VALUE USING INTELLIGENT TESTER (REAR HEIGHT CONTROL SENSOR) |
Using the intelligent tester, read the Data List (Click here).
AFS Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Height Sens Pw Supply Val
Height control sensor power supply value / 0 to 6.25 V
4.7 to 5.2 V
-
Fr Height Sens Signal Val
Front height control sensor signal value / 0 to 5 V
Approximately 2.5 V (When vehicle level)
The value changes according to the vehicle height.
Rr Height Sens Signal Val
Rear height control sensor signal value / 0 to 5 V
Approximately 2.5 V (When vehicle level)
The value changes according to the vehicle height.
- OK:
- Normal conditions listed above are displayed.
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 11. CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - SUSPENSION CONTROL ECU) |
Disconnect the E101 headlight swivel ECU connector.
Disconnect the K35 and K36 suspension control ECU connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E101-18 (SBR) - K35-23 (SHB5)
Always
Below 1 Ω
E101-19 (SHRL) - K36-28 (SHR2)
Always
Below 1 Ω
E101-17 (SHFL) - K35-22 (SHF2)
Always
Below 1 Ω
E101-21 (SGR) - K35-11 (SHG5)
Always
Below 1 Ω
E101-18 (SBR) - Body ground
Always
10 kΩ or higher
E101-19 (SHRL) - Body ground
Always
10 kΩ or higher
E101-17 (SHFL) - Body ground
Always
10 kΩ or higher
E101-21 (SGR) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 12. CHECK SUSPENSION CONTROL ECU |
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
K35-23 (SHB5) - K35-11 (SHG5)
Ignition switch ON
4.5 to 5.5 V
K35-22 (SHF2) - K35-11 (SHG5)
Ignition switch ON
Approximately 2.5 V (When vehicle level)
(The value changes according to the vehicle height)
K36-28 (SHR2) - K35-11 (SHG5)
Ignition switch ON
Approximately 2.5 V (When vehicle level)
(The value changes according to the vehicle height)
Text in Illustration *a
Component with harness connected
(Suspension Control ECU)
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
