P1603 Engine Stall History
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- P1605 Rough Idling
DESCRIPTION
- P1603
Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle has ran out of fuel before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P1603 |
After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the engine switch being operated for 0.5 seconds or more (1 trip detection logic). |
|
- P1605
Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P1605 |
After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic). |
|
INSPECTION PROCEDURE
- HINT:
- In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.
As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.
- If any other DTCs are output, perform troubleshooting for those DTCs first.
- Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.
Symptom
Suspected Area
Engine vibration occurs and engine stops
Air-fuel ratio abnormal
Engine stops with no engine vibration
Ignition system, injection stoppage, high load from external parts
Engine can be started with accelerator pedal depressed
Insufficient air volume
Rough idling after engine started
Air-fuel ratio abnormal, abnormal combustion
- Read freeze frame data using the GTS. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
- When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (Click here).
- When DTC P1603 (Engine Stall History) is stored, DTC P1605 (Rough Idling) is also stored. When confirming freeze frame data, check DTC P1605. The ECM stores DTC P1605 first. Therefore, 5 sets of freeze frame data can be confirmed through DTC P1605, enabling the technician to obtain more information.
- When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
- Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
- Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.
- When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
- In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.
- Inspection flow:
- Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.
- P1603:


- If the engine stalled when the intake air volume was low (during idling or deceleration), there may be a decrease in torque due to an incorrect air-fuel ratio, etc.
- If the engine stalled when the intake air volume was high (during driving or acceleration), there may be a major malfunction such as continuous misfire due to ignition stoppage, fuel injection stoppage, etc. and the torque drops to zero.
- If the engine speed decreased slowly, there may have been a decrease in torque due to an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.
- If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.
- If the air-fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.
- If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.
| Vehicle State |
Engine Speed |
Suspected Area |
Primary Parts to Inspect |
Procedure |
|
| Idling or decelerating |
Slowly decreases and engine stalls |
Ignition system abnormal |
Igniter abnormal |
|
38, 52 |
| Air-fuel ratio abnormal |
Air suction |
|
5, 6 |
||
| Sensor malfunction (value from sensor too lean) |
|
7 to 19 |
|||
| Sensor malfunction (value from sensor too rich) |
35 to 47 |
||||
| Fuel supply problem |
|
20 to 33 |
|||
| Intake air volume insufficient |
Problem with air passage |
|
49 to 51 |
||
| Excessive valve overlap |
|
52 to 55 |
|||
| Ignition timing incorrect |
Does not operate as expected |
|
56 to 60 |
||
| Rapidly decreases and engine stalls* |
Ignition and injection stops (electrical system malfunction) |
Power temporarily cut |
|
61, 62 |
|
| External part malfunctioning |
Increase in load |
|
63 to 65 |
||
| Accelerating |
- |
Crankshaft position sensor or VVT sensor malfunction |
Power temporarily cut |
|
1 |
| Mass air flow meter |
Foreign matter adhesion |
|
66 to 69 |
||
| Ignition and injection stops (electrical system malfunction) |
Power temporarily cut |
|
70, 71 |
||
| Fuel supply problem |
Fuel leak, clog |
|
72 to 76 |
||
- P1605:


- If the engine speed decreased slowly, there may have been a decrease in torque due to an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.
- If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.
- If the air-fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.
- If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.
| Engine Speed |
Suspected Area |
Primary Parts to Inspect |
Procedure |
|
| Slowly decreases and engine stalls |
Ignition system abnormal |
Igniter abnormal |
|
38, 52 |
| Air-fuel ratio abnormal |
Air suction |
|
5, 6 |
|
| Sensor malfunction (value from sensor too lean) |
|
7 to 19 |
||
| Sensor malfunction (value from sensor too rich) |
35 to 47 |
|||
| Fuel supply problem |
|
20 to 33 |
||
| Intake air volume insufficient |
Problem with air passage |
|
49 to 51 |
|
| Excessive valve overlap |
|
52 to 55 |
||
| Ignition timing incorrect |
Does not operate as expected |
|
56 to 60 |
|
| Rapidly decreases and engine stalls* |
Ignition and injection stops (electrical system malfunction) |
Power temporarily cut |
|
61, 62 |
| External part malfunctioning |
Increase in load |
|
63 to 65 |
|
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK FOR ANY OTHER DTCS OUTPUT |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Read the DTCs (Click here).
Result Result
Proceed to
Only DTC P1603 and/or P1605 is output
A
DTCs other than P1603 and/or P1605 are output
B
- HINT:
- If any DTCs other than P1603 or P1605 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. CHECK FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
- OK:
- Immobiliser Fuel Cut is OFF.
Result Result
Proceed to
Abnormal
A
Normal
B
|
|
||||
| A | |
| 3. CHECK ENGINE IMMOBILISER SYSTEM |
Connect the GTS to the DLC3.
Start the engine.
Idle the engine
Enter the following menus: Powertrain / Engine and ECT / Data List / Immobiliser Communication and Immobiliser Fuel Cut.
Check the Data List indication.
Result Data List Item
Result
Immobiliser Communication
ON
Immobiliser Fuel Cut
OFF
|
|
||||
| OK | |
| 4. READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Problem Symptom
Freeze Frame Data Item for DTC P1605
Suspected Area
Proceed to
Closed Throttle Position SW
Engine Speed
Total of Short FT and Long FT
When idling or decelerating, engine speed slowly decreases and engine stalls
All 5 sets of freeze frame data are ON
Decreases slowly*1
All 5 sets of freeze frame data are +15% or more*2
- Air suction
- Sensor malfunction (value from sensor too lean)
- Fuel supply problem
A
At least 1 of the 5 sets of freeze frame data is -15% or less*3
Sensor malfunction (value from sensor too rich)
B
All 5 sets of freeze frame data are from -15% to +15%
- Intake air volume insufficient
- Ignition timing incorrect
C
When idling or decelerating, engine speed rapidly decreases and engine stalls
Decreases rapidly*1
-
- Injection stoppage, ignition stoppage
- Load from external parts
D
When accelerating or driving at constant speed, engine stalls*4
At least one is OFF
-
-
- Sensor malfunction
- Injection stoppage, ignition stoppage
- Fuel supply problem
E


- HINT:
- *1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.
Otherwise, the engine speed is considered to have decreased slowly.
- In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or more.
- In the freeze frame data, the engine speed at #5 is 120 rpm or less.
- *1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.
- If the vehicle speed is 30 km/h or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transmission. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)
- *2: When a DTC is stored, feedback compensation increases because the air-fuel ratio is determined to be lean.
- *3: When a DTC is stored, feedback compensation decreases because the air-fuel ratio is determined to be rich.
- *4: This item should be checked when DTC P1603 is output and is not necessary to check when only P1605 is output.
- If the vehicle speed is 30 km/h or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transmission. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)
- Air suction
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 5. CHECK INTAKE SYSTEM |
Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (Click here).
- HINT:
- If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
- If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.
- If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
- OK:
- There is no air leakage.
|
|
||||
| OK | |
| 6. CHECK PURGE VSV |
Disconnect the purge hose (on the canister side) of the purge VSV.

Start the engine.
Idle the engine.
Disconnect the connector of the purge VSV.
Check if air flows through the purge VSV.
- OK:
- Air does not flow.
Connect the connector of the purge VSV.
Connect the purge hose of the purge VSV.
- HINT:
- When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).
|
|
||||
| OK | |
| 7. READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Calculate Load
Below 90% of the current value of the vehicle*1
Mass air flow meter
A
AFS Voltage B1S1
AFS Voltage B2S1
3.3 V or higher*2
- Air fuel ratio sensor
- Wire harness or connector
B
- HINT:
- *1: If the mass air flow meter is malfunctioning and incorrectly measures the pressure to be less than the actual intake manifold pressure, the freeze frame data will show a low engine load value.
- *2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is lean, the actual air-fuel ratio will become rich and the engine may stall.
- *1: If the mass air flow meter is malfunctioning and incorrectly measures the pressure to be less than the actual intake manifold pressure, the freeze frame data will show a low engine load value.
- Air fuel ratio sensor
|
|
||||
| A | |
| 8. CHECK MASS AIR FLOW METER |
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass airflow meter.
Result Result
Proceed to
Visible foreign matter is not present
A
Visible foreign matter is present
B
|
|
||||
| A | |
| 9. CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER) |
Check the harnesses and connectors, referring to DTC P0102 inspection procedure (Click here).
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 10. PERFORM DRIVE TEST |
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
- HINT:
- The A/C switch and all accessory switches should be off.
Idle the engine.
Using the GTS, read the value of Calculate Load in the Data List.
- Standard:
Data List
Specified Condition
Calculate Load
90 to 110% of the current value of the vehicle
Result Result
Proceed to
Abnormal
A
Normal
B
|
|
||||
| A | ||
| ||
| 11. PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the GTS to the DLC3.

Turn the engine switch on (IG).
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
- Standard:
Tester Display
Specified Condition
Control the Injection Volume for A/F Sensor (+12.5%)
Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%)
Air fuel ratio sensor output voltage is higher than 3.4 V
Result Result
Proceed to
Abnormal
A
Normal
B
- HINT:
- The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
|
|
||||
| A | |
| 12. CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE) |
Check the harnesses and connectors, referring to DTC P0031 inspection procedure (Click here).
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 13. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P2237 inspection procedure (Click here).
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 14. READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Proceed to
Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp
Difference in temperature between each item is less than 10°C*1
A
Difference in temperature between each item is 10°C or more*2
B
- HINT:
- *1: A long time had elapsed after stopping the engine.
- *2: A long time had not elapsed after stopping the engine.
- *1: A long time had elapsed after stopping the engine.
|
|
||||
| A | |
| 15. READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).


Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time
Range A
- Engine coolant temperature sensor
- Water inlet with thermostat sub-assembly
A
Range B
Engine coolant temperature sensor
B
Range C
-
C
- HINT:
- This step is not directly related to engine stall.
- Engine coolant temperature sensor
|
|
||||
|
|
||||
| A | |
| 16. INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY |
- HINT:
- For the water inlet with thermostat sub-assembly inspection, refer to the following procedures (Click here).
| Result |
Proceed to |
| Abnormal |
A |
| Normal |
B |
|
|
||||
| A | ||
| ||
| 17. READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Coolant Temp
120°C or higher
Engine coolant temperature sensor
A
Coolant Temp, Ambient Temp for A/C
Engine coolant temperature is lower than outside temperature by 15°C or more
Engine coolant temperature sensor
Both freeze frame data items listed above
Values are other than above
-
B
|
|
||||
| A | |
| 18. INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
- HINT:
- For the engine coolant temperature sensor inspection, refer to the following procedures (Click here).
| Result |
Proceed to |
| Normal |
A |
| Abnormal |
B |
|
|
||||
| A | |
| 19. CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR) |
Disconnect the ECM connector.
Disconnect the engine coolant temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
C18-2 - C45-76 (THW)
Always
Below 1 Ω
C18-1 - C45-97 (ETHW)
Always
Below 1 Ω
C18-2 or C45-76 (THW) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 20. READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
EVAP (Purge) VSV
At least 1 of the 5 sets of freeze frame data is not 0%
Purge VSV
A
All 5 sets of freeze frame data are 0%
-
B
- HINT:
- If the purge VSV is stuck closed, air-fuel ratio compensation by the purge VSV is incorrectly adjusted, and then the air-fuel ratio becomes lean and the engine may stall.
|
|
||||
| A | |
| 21. PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL) |
Disconnect the purge hose (on the canister side) of the purge VSV.

Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.
Operate the purge VSV and check the airflow.
- OK:
Activate the VSV for Evap Control
Specified Condition
ON
Air flows
OFF
Air does not flow
Result Result
Proceed to
NG
A
OK
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | |
| 22. INSPECT PURGE VSV |
Inspect the purge VSV (Click here).
|
|
||||
| OK | |
| 23. CHECK TERMINAL VOLTAGE (PURGE VSV POWER SOURCE) |
Disconnect the purge VSV connector.

Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C55-1 - Body ground
Engine switch on (IG)
11 to 14 V
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 24. CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM) |
Disconnect the purge VSV connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
C55-2 - C45-63 (PRG)
Always
Below 1 Ω
C55-2 or C45-63 (PRG) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 25. CLEAR DTC |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (Click here).
| NEXT | |
| 26. READ VALUE USING GTS (EVAP (Purge) VSV) |
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
- HINT:
- The A/C switch and all accessory switches should be off.
Idle the engine for 15 minutes or more.
Using the GTS, read the value of EVAP (Purge) VSV in the Data List.
- Standard:
Data List
Specified Condition
EVAP (Purge) VSV
Value other than 0% is displayed
Result Result
Proceed to
Abnormal
A
Normal
B
|
|
||||
| A | |
| 27. PERFORM ACTIVE TEST USING GTS |
Disconnect the purge hose (on the canister side) of the purge VSV.

Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.
Operate the purge VSV and check the airflow.
- OK:
Activate the VSV for Evap Control
Specified Condition
ON
Air flows
OFF
Air does not flow
Result Result
Proceed to
NG
A
OK
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | |
| 28. CHECK CONNECTOR CONNECTION CONDITION (ECM) |
Check the ECM connector connection condition.
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 29. PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.
When performing the Active Test, check for an operating sound from the fuel pump.
- Standard:
Control the Fuel Pump Duty
Specified Condition
25 or 80%
Operating sound heard
OFF
Operating sound not heard
Result Result
Proceed to
Abnormal
A
Normal
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
- If the fuel pump operating noise is abnormal, proceed to step 34.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | |
| 30. INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
|
||||
| OK | ||
| ||
| 31. CHECK FUEL SYSTEM |
Check the fuel system.
- Check the fuel pump operation.
- Check the fuel leaks.
- Check the fuel pressure.
- Check the fuel pump operation.
- HINT:
- For the fuel system On-vehicle Inspection, refer to the following procedures (Click here).
| Result |
Proceed to |
| Abnormal |
A |
| Normal |
B |
|
|
||||
| A | |
| 32. CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
Result Result
Proceed to
There is foreign matter or signs that fuel pump was stuck
A
There is no foreign matter and no signs that fuel pump was stuck
B
- HINT:
- If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.
|
|
||||
| A | |
| 33. CHECK FUEL SYSTEM |
Check the fuel system.
- Check the fuel pump operation.
- Check the fuel leaks.
- Check the fuel pressure.
- Check the fuel pump operation.
- HINT:
- For the fuel system On-vehicle Inspection, refer to the following procedures (Click here).
|
|
||||
| OK | ||
| ||
| 34. CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
|
||||
| OK | |
| 35. READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Calculate Load
110% or more of the current value of the vehicle*1
Mass air flow meter
A
AFS Voltage B1S1
AFS Voltage B2S1
Below 3.3 V*2
- Air fuel ratio sensor
- Harness and connector
B
Both freeze frame data items listed above
Values are other than above
-
C
- HINT:
- *1: If the mass air flow meter is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake manifold, the freeze frame data will show a high engine load value.
- *2: As the air fuel ratio sensor output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is rich, the actual air-fuel ratio will become lean and the engine may stall.
- *1: If the mass air flow meter is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake manifold, the freeze frame data will show a high engine load value.
- Air fuel ratio sensor
|
|
||||
|
|
||||
| A | |
| 36. CHECK MASS AIR FLOW METER |
Remove the mass airflow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
Result Result
Proceed to
Visible foreign matter is not present
A
Visible foreign matter is present
B
|
|
||||
| A | |
| 37. CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER) |
Check the harnesses and connectors, referring to DTC P0102 inspection procedure (Click here).
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 38. PERFORM DRIVE TEST |
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
- HINT:
- The A/C switch and all accessory switches should be off.
Idle the engine.
Using the GTS, read the value of Calculate Load in the Data List.
- Standard:
Data List
Specified Condition
Calculate Load
90 to 110% of the current value of the vehicle
|
|
||||
| OK | |
| 39. PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the GTS to the DLC3.

Turn the engine switch on (IG).
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
- Standard:
Tester Display
Specified Condition
Control the Injection Volume for A/F Sensor (+12.5%)
Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%)
Air fuel ratio sensor output voltage is higher than 3.4 V
Result Result
Proceed to
Abnormal
A
Normal
B
- HINT:
- The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
|
|
||||
| A | |
| 40. CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE) |
Check the harnesses and connectors, referring to DTC P0031 inspection procedure (Click here).
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 41. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P2237 inspection procedure (Click here).
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 42. READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Proceed to
Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp
Difference in temperature between each item is less than 10°C*1
A
Difference in temperature between each item is 10°C or more*2
B
- HINT:
- *1: A long time had elapsed after stopping the engine.
- *2: A long time had not elapsed after stopping the engine.
- *1: A long time had elapsed after stopping the engine.
|
|
||||
| A | |
| 43. READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).


Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time
Range A
- Engine coolant temperature sensor
- Water inlet with thermostat sub-assembly
A
Range B
Engine coolant temperature
B
Range C
-
C
- HINT:
- This step is not directly related to engine stall.
- Engine coolant temperature sensor
|
|
||||
|
|
||||
| A | |
| 44. INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY |
- HINT:
- For the water inlet with thermostat sub-assembly inspection, refer to the following procedures (Click here).
| Result |
Proceed to |
| Abnormal |
A |
| Normal |
B |
- HINT:
- This step is not directly related to engine stall.
|
|
||||
| A | ||
| ||
| 45. READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Coolant Temp
120°C or higher
Engine coolant temperature sensor
A
Coolant Temp, Ambient Temp for A/C
Engine coolant temperature is lower than outside temperature by 15°C or more
Engine coolant temperature sensor
Both freeze frame data items listed above
Values are other than above
-
B
|
|
||||
| A | |
| 46. INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
- HINT:
- For the engine coolant temperature sensor inspection, refer to the following procedures (Click here).
| Result |
Proceed to |
| Normal |
A |
| Abnormal |
B |
|
|
||||
| A | |
| 47. CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR) |
Disconnect the ECM connector.
Disconnect the engine coolant temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
C18-2 - C45-76 (THW)
Always
Below 1 Ω
C18-1 - C45-97 (ETHW)
Always
Below 1 Ω
C18-2 or C45-76 (THW) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 48. CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
|
||||
| OK | |
| 49. READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Result
Suspected Area
Proceed to
Total of ISC Learning Value and ISC Feedback Value
Below 80% of the current value of the vehicle
Intake air volume insufficient
A
80% or more of the current value of the vehicle
B
|
|
||||
| A | |
| 50. CHECK INTAKE SYSTEM |
Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (Click here).
- HINT:
- If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
- If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.
- If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
- OK:
- There is no air leakage.
|
|
||||
| OK | |
| 51. CHECK INTAKE SYSTEM |
Check the intake system.
- Inspect the mass air flow meter.
- Check the PCV hose.
- Inspect the PCV valve.
- Inspect the purge VSV.
Result Result
Proceed to
Abnormal
A
Normal
B
- Inspect the mass air flow meter.
|
|
||||
| A | ||
| ||
| 52. PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR) |
Connect the GTS to the DLC3.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank1) or Control the VVT Linear (Bank2).
- HINT:
- When performing the Active Test, make sure the A/C is on and the shift lever is in P or N.
Check the engine speed while operating the camshaft timing oil control valve using the GTS.
- OK:
Tester Operation
Specified Condition
0%
Normal engine speed
100%
Engine idles roughly or stalls
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
- If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 53. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM) |
Check the harnesses and connectors, referring to DTC P0010 inspection procedure (Click here).
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 54. PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR) |
Connect the GTS to the DLC3.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank1) or Control the VVT Exhaust Linear (Bank2).
- HINT:
- When performing the Active Test, make sure the A/C is on and the shift lever is in P or N.
Check the engine speed while operating the camshaft timing oil control valve using the GTS.
- OK:
Tester Operation
Specified Condition
0%
Normal engine speed
100%
Engine idles roughly or stalls
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
- If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 55. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM) |
Check the harnesses and connectors, referring to DTC P0013 inspection procedure (Click here).
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 56. READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Suspected Area
Proceed to
IGN Advance
Knock Correct Learn Value
Differs from the current value of the vehicle by 10° or more
Less than 3°
- Engine coolant temperature sensor
- Mass air flow meter
- Knock sensor
A
3° or more
-
B
Differs from the current value of the vehicle by less than 10°
-
-
- Engine coolant temperature sensor
|
|
||||
| A | |
| 57. INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
- HINT:
- For the engine coolant temperature sensor inspection, refer to the following procedures (Click here).
|
|
||||
| OK | |
| 58. CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR) |
Disconnect the ECM connector.
Disconnect the engine coolant temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
C18-2 - C45-76 (THW)
Always
Below 1 Ω
C18-1 - C45-97 (ETHW)
Always
Below 1 Ω
C18-2 or C45-76 (THW) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 59. INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR) |
Inspect the mass air flow meter (Click here).
- HINT:
- If the intake air temperature sent to the ECM is higher than the standard due to the mass air flow meter (intake air temperature sensor) malfunctioning, the ignition timing may become delayed.
|
|
||||
| OK | |
| 60. READ VALUE USING GTS |
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
- HINT:
- The A/C switch and all accessory switches should be off.
Idle the engine.
Using the GTS, read the value of IGN Advance and Knock Correct Learn Value in the Data List.
Result Freeze Frame Data Item for DTC P1605
Proceed to
IGN Advance
Knock Correct Learn Value
Differs from the current value of the vehicle by 10° or more
Less than 3°
A
3° or more
B
Differs from the current value of the vehicle by less than 10°
-
- HINT:
- If the results of the checks performed in steps 56 to 64 were all normal and the sum of ISC Feedback Value and ISC Learning Value in the Data List is 120% of the normal value or more, check for carbon deposits in the throttle body assembly. If there are carbon deposits, clean them off to finish the troubleshooting procedure.
|
|
||||
| A | ||
| ||
| 61. CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE) |
Disconnect the fuel injector assembly connectors.

Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Cylinder
Tester Connection
Switch Condition
Specified Condition
No. 1
a5-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 2
a1-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 3
a6-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 4
a2-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 5
a7-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 6
a3-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 7
a8-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 8
a4-2 - Body ground
Engine switch on (IG)
11 to 14 V
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 62. CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
|
||||
| OK | |
| 63. CHECK FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Suspected Area
Proceed to
A/C Signal
Air Conditioner FB Val
Power Steering Signal
A/C Signal display does not change from OFF
Value displayed for Air Conditioner FB Val does not increase
Changes from OFF to ON
Power steering system
A
Does not change from OFF
-
A/C Signal display changes from OFF to ON*1
Value displayed for Air Conditioner FB Val increases
Changes from OFF to ON
Power steering system
Does not change from OFF
A/C system
B
- HINT:
- *1: Check not only the on/off state of the air conditioner but also the change in air conditioner load.
- The normal value for the ISC learned value is engine displacement (liters) x 0.9.
- Even if the results are normal, the power steering system and/or A/C system may have been malfunctioning. If there are no problems with other parts, inspect the power steering system and/or A/C system.
- *1: Check not only the on/off state of the air conditioner but also the change in air conditioner load.
|
|
||||
| A | |
| 64. CHECK FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Suspected Area
Proceed to
Electrical Load Signal or Electric Load Feedback Val
Electric Load Feedback Val
Difference between Engine Speed and SPD (NT)
Vehicle Speed
Electrical Load Signal display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1
Value displayed for Electric Load Val changes
-
-
Electrical load signal circuit
C
Value displayed for Electric Load Val does not change
At least 1 of the 5 sets of freeze frame data is less than 100 rpm
Less than 30 km/h
A/T system
B
30 km/h or more
-
A
All 5 sets of freeze frame data are 100 rpm or more
-
-
A
Electrical Load Signal display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase
-
At least 1 of the 5 sets of freeze frame data is less than 100 rpm
Less than 30 km/h
A/T system
B
30 km/h or more
-
A
All 5 sets of freeze frame data are 100 rpm or more
-
-
A
- HINT:
- *1: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.
- The normal value for the ISC learned value is engine displacement (liters) x 0.9.
- Even if the results are normal, the electrical load signal system and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the electrical load system and/or A/T system.
- *1: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.
|
|
||||
|
|
||||
| A | |
| 65. CHECK FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item for DTC P1605
Suspected Area
Proceed to
Shift SW Status (P Range)
Shift SW Status (N Range)
Neutral Position SW Signal
P and N position are both OFF in at least one data set
In D or R, NSW is ON
Park/neutral position switch assembly
A
In D or R, NSW is OFF
A/T system
B
All 5 sets of freeze frame data are ON
-
-
C
- HINT:
- Even if the results are normal, the park/neutral position switch assembly and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch assembly and/or A/T system.
|
|
||||
|
|
||||
| A | ||
| ||
| 66. CHECK FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item
Result
Suspected Area
Proceed to
Throttle Sensor Position, Calculate Load
Calculate Load decreases while Throttle Sensor Position increases
Mass air flow meter
A
Calculate Load does not decrease while Throttle Sensor Position increases
-
B
|
|
||||
| A | |
| 67. CHECK MASS AIR FLOW METER |
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass airflow meter.
Result Result
Proceed to
Visible foreign matter is not present
A
Visible foreign matter is present
B
|
|
||||
| A | |
| 68. CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER) |
Check the harnesses and connectors, referring to DTC P0102 inspection procedure (Click here).
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 69. PERFORM DRIVE TEST |
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
- HINT:
- The A/C switch and all accessory switches should be off.
Idle the engine.
Using the GTS, read the value of Calculate Load in the Data List.
- Standard:
Data List
Specified Condition
Calculate Load
90 to 110% of the current value of the vehicle
|
|
||||
| OK | |
| 70. CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE) |
Disconnect the fuel injector assembly connectors.

Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Cylinder
Tester Connection
Switch Condition
Specified Condition
No. 1
a5-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 2
a1-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 3
a6-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 4
a2-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 5
a7-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 6
a3-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 7
a8-2 - Body ground
Engine switch on (IG)
11 to 14 V
No. 8
a4-2 - Body ground
Engine switch on (IG)
11 to 14 V
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 71. CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
|
||||
| OK | |
| 72. PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.
When performing the Active Test, check for an operating sound from the fuel pump.
- Standard:
Control the Fuel Pump Duty
Specified Condition
25 or 80%
Operating sound heard
OFF
Operating sound not heard
Result Result
Proceed to
Abnormal
A
Normal
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
- If the fuel pump operating noise is abnormal, proceed to step 77.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | |
| 73. INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
|
||||
| OK | ||
| ||
| 74. CHECK FUEL SYSTEM |
Check the fuel system.
- Check the fuel pump operation.
- Check the fuel leaks.
- Check the fuel pressure.
- Check the fuel pump operation.
- HINT:
- For the fuel system On-vehicle Inspection, refer to the following procedures (Click here).
| Result |
Proceed to |
| Abnormal |
A |
| Normal |
B |
|
|
||||
| A | |
| 75. CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
Result Result
Proceed to
There is foreign matter or signs that fuel pump was stuck
A
There is no foreign matter and no signs that fuel pump was stuck
B
- HINT:
- If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.
|
|
||||
| A | |
| 76. CHECK FUEL SYSTEM |
Check the fuel system.
- Check the fuel pump operation.
- Check the fuel leaks.
- Check the fuel pressure.
- Check the fuel pump operation.
- HINT:
- For the fuel system On-vehicle Inspection, refer to the following procedures (Click here).
|
|
||||
| OK | ||
| ||
| 77. CLEAR DTC |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (Click here).
| NEXT | ||
| ||
