2011-2013 Land Cruiser · Service Manual Power Source / Network

U1002 (CAN No. 2 BUS) Lost Communication with Gateway Module (Network Gateway ECU)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).
DTC Code
Symptoms
Trouble Area
U1002 (CAN No. 2 BUS)
Lost communication with the gateway module (network gateway ECU).
  1. Movement control bus circuit
  2. 4WD control ECU branch wire or connector
  3. Yaw rate sensor branch wire or connector
  4. Seat belt control ECU branch wire or connector*1
  5. Clearance warning ECU branch wire or connector*2
  6. Parking assist ECU branch wire or connector*3
  7. Skid control ECU branch wire or connector
  8. Steering angle sensor branch wire or connector
  9. Network gateway ECU main wire or connector
  10. Suspension control ECU branch wire or connector*4
  11. Steering control ECU branch wire or connector*5
  12. 4WD control ECU
  13. Yaw rate sensor
  14. Seat belt control ECU*1
  15. Clearance warning ECU*2
  16. Parking assist ECU*3
  17. Skid control ECU
  18. Steering angle sensor
  19. Suspension control ECU*4
  20. Steering control ECU *5
  21. Network gateway ECU
  22. No. 4 junction connector
  23. No. 5 junction connector
  24. No. 6 junction connector
  25. No. 7 junction connector
  26. No. 1 CAN junction connector

HINT:
*1: w/ Pre-Crash Safety System
*2: w/ TOYOTA Parking Assist-sensor System
*3: w/ Parking Assist Monitor System
*4: w/ Active Height Control Suspension System
*5: w/ Variable Gear Ratio Steering System


WIRING DIAGRAM

C176037E01
C246779E01

INSPECTION PROCEDURE


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)

  1. C176199E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance Malfunction
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    54 to 69 Ω
    70 Ω or higher: Open in CAN main bus line
    E31-13 (CA2H) - E31-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    E31-12 (CA2L) - E31-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    E31-13 (CA2H) - E31-4 (GND)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    E31-12 (CA2L) - E31-4 (GND)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short

    Result 
    Result
    Proceed to
    NG
    1. Open in CAN main wire
    A
    NG
    1. Short in line
    2. +B short
    3. Ground short
    B
    OK
    C



B
Go to step 18

C
Go to step 60
A


3. CHECK FOR OPEN IN MAIN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. C174233E43
    Disconnect the E71 No. 7 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E71-1 (CANH) - E71-12 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 5
OK


4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 7 JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

  1. C174233E44
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E71-3 (CANH) - E71-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 14
OK

REPAIR OR REPLACE NO. 7 JUNCTION CONNECTOR

5. CONNECT CONNECTOR
  1. Reconnect the E71 No. 7 junction connector connector.


NEXT


6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION BLOCK)

  1. C174233E26
    except Double Swing Out Type:
    1. Disconnect the F21 No. 6 junction connector connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      F21-2 (CANH) - F21-13 (CANL)
      Ignition switch off
      108 to 132 Ω

  1. C174233E60
    for Double Swing Out Type:
    1. Disconnect the F73 No. 6 junction connector connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      F73-6 (CANH) - F73-17 (CANL)
      Ignition switch off
      108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
OK


7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. C174233E27
    except Double Swing Out Type:
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      F21-3 (CANH) - F21-14 (CANL)
      Ignition switch off
      108 to 132 Ω

  1. C174233E61
    for Double Swing Out Type:
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      F73-7 (CANH) - F73-18 (CANL)
      Ignition switch off
      108 to 132 Ω



NG
Go to step 8
OK

REPAIR OR REPLACE NO. 6 JUNCTION CONNECTOR

8. CONNECT CONNECTOR
  1. Reconnect the F21*1 or F73*2 No. 6 junction connector connector.

    1. *1: except Double Swing Out Type
    2. *2: for Double Swing Out Type


NEXT


9. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

  1. C174233E25
    Disconnect the E68 No. 5 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E68-2 (CANH) - E68-13 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
OK


10. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
C174233E24
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E68-1 (CANH) - E68-12 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 11
OK

REPAIR OR REPLACE NO. 5 JUNCTION CONNECTOR

11. CONNECT CONNECTOR
  1. Reconnect the E68 No. 5 junction connector connector.


NEXT


12. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
C174233E45
  1. Disconnect the E74 No. 4 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E74-1 (CANH) - E74-12 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK


13. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
C174233E46
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E74-2 (CANH) - E74-13 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 16
OK

REPAIR OR REPLACE NO. 4 CAN JUNCTION CONNECTOR

14. CONNECT CONNECTOR
  1. Reconnect the E71 No. 7 junction connector connector.


NEXT


15. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
C176200E01
  1. Disconnect the K29 No. 1 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    K29-1 (CANH) - K29-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)
OK

REPAIR OR REPLACE NO. 1 CAN JUNCTION CONNECTOR

16. CONNECT CONNECTOR
  1. Reconnect the E74 No. 4 junction connector connector.


NEXT


17. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NETWORK GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)
C176211E01
  1. Disconnect the E31 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (NETWORK GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)
OK

REPLACE NETWORK GATEWAY ECU (Click here)

18. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR SIDE)
C176201E02
  1. Disconnect the E71 No. 7 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    E31-13 (CA2H) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E31-12 (CA2L) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E31-13 (CA2H) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E31-12 (CA2L) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Result 
    Result
    Proceed to
    OK (w/ Pre-Crash Safety System)
    A
    OK (w/o Pre-Crash Safety System)
    B
    NG
    C



B
Go to step 20

C
Go to step 21
A


19. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU)

  1. C176202E10
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E71-2 (CANH) - E71-13 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E71-2 (CANH) - E71-13 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E71-2 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E71-13 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E71-2 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E71-13 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E71-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E71-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E71-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E71-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 37
OK


20. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)
C175844E10
  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Result
    Type
    Proceed to
    E71-3 (CANH) - E71-14 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    -
    A
    E71-3 (CANH) - E71-14 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    w/ Active Height Control Suspension
    B
    w/o Active Height Control Suspension
    C
    E71-3 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    -
    A
    E71-14 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    -
    A
    E71-3 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    w/ Active Height Control Suspension
    B
    w/o Active Height Control Suspension
    C
    E71-14 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    w/ Active Height Control Suspension
    B
    w/o Active Height Control Suspension
    C
    E71-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    -
    A
    E71-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    -
    A
    E71-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    w/ Active Height Control Suspension
    B
    w/o Active Height Control Suspension
    C
    E71-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    w/ Active Height Control Suspension
    B
    w/o Active Height Control Suspension
    C



B
Go to step 39

C
Go to step 42
A

REPAIR OR REPLACE NO. 7 JUNCTION CONNECTOR

21. CONNECT CONNECTOR
  1. Reconnect the E71 No. 7 junction connector connector.


NEXT


22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

  1. C176202E01
    except Double Swing Out Type:
    1. Disconnect the F21 No. 6 junction connector connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      F21-2 (CANH) - F21-13 (CANL)
      Ignition switch off
      108 to 132 Ω
      F21-2 (CANH) - E22-4 (CG)
      Ignition switch off
      200 Ω or higher
      F21-13 (CANL) - E22-4 (CG)
      Ignition switch off
      200 Ω or higher
      F21-2 (CANH) - E22-16 (BAT)
      Ignition switch off
      6 kΩ or higher
      F21-13 (CANL) - E22-16 (BAT)
      Ignition switch off
      6 kΩ or higher

  1. C176202E16
    for Double Swing Out Type:
    1. Disconnect the F73 No. 6 junction connector connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      F73-6 (CANH) - F73-17 (CANL)
      Ignition switch off
      108 to 132 Ω
      F73-6 (CANH) - E22-4 (CG)
      Ignition switch off
      200 Ω or higher
      F73-17 (CANL) - E22-4 (CG)
      Ignition switch off
      200 Ω or higher
      F73-6 (CANH) - E22-16 (BAT)
      Ignition switch off
      6 kΩ or higher
      F73-17 (CANL) - E22-16 (BAT)
      Ignition switch off
      6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
OK


23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)

  1. C176201E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    E31-13 (CA2H) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E31-12 (CA2L) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E31-13 (CA2H) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E31-12 (CA2L) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Result 
    Tester Connection
    Switch Condition
    OK
    A
    NG (w/ TOYOTA Parking Assist-sensor System)
    B
    NG (w/ Parking Assist Monitor System)
    C
    NG (w/o TOYOTA Parking Assist-sensor System and w/o Parking Assist Monitor System)
    D



B
Go to step 24

C
Go to step 25

D
Go to step 26
A

REPAIR OR REPLACE NO. 6 JUNCTION CONNECTOR

24. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - CLEARANCE WARNING ECU)

  1. C176202E02
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    F21-1 (CANH) - F21-12 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    F21-1 (CANH) - F21-12 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    F21-1 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    F21-12 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    F21-1 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    F21-12 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    F21-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    F21-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    F21-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    F21-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 44
OK

REPAIR OR REPLACE NO. 6 JUNCTION CONNECTOR

25. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - PARKING ASSIST ECU)

  1. C176202E09
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    F21-1 (CANH) - F21-12 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    F21-1 (CANH) - F21-12 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    F21-1 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    F21-12 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    F21-1 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    F21-12 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    F21-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    F21-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    F21-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    F21-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 46
OK

REPAIR OR REPLACE NO. 6 JUNCTION CONNECTOR

26. CONNECT CONNECTOR
  1. Reconnect the F21*1 or F73*2 No. 6 junction connector connector.

    1. *1: except Double Swing Out Type
    2. *2: for Double Swing Out Type


NEXT


27. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

  1. C176202E08
    Disconnect the E68 No. 5 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E68-2 (CANH) - E68-13 (CANL)
    Ignition switch off
    108 to 132 Ω
    E68-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E68-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E68-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E68-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK


28. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR SIDE)

  1. C176201E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    E31-13 (CA2H) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E31-12 (CA2L) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E31-13 (CA2H) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E31-12 (CA2L) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 30
OK


29. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - YAW RATE SENSOR)

  1. C176202E04
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E68-3 (CANH) - E68-14 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E68-3 (CANH) - E68-14 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E68-3 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E68-14 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E68-3 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E68-14 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E68-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E68-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E68-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E68-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 48
OK

REPAIR OR REPLACE NO. 5 JUNCTION CONNECTOR

30. CONNECT CONNECTOR
  1. Reconnect the E68 No. 5 junction connector connector.


NEXT


31. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
C176202E11
  1. Disconnect the E74 No. 4 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E74-1 (CANH) - E74-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    E74-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E74-12 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E74-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E74-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


32. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU)
C176202E12
  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E74-6 (CANH) - E74-17 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E74-6 (CANH) - E74-17 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E74-6 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E74-17 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E74-6 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E74-17 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E74-6 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E74-17 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E74-6 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E74-17 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 50
OK


33. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - STEERING CONTROL ECU)
C175844E11

NOTICE:
For vehicles without the variable gear ratio steering system, go to "Check for Short in CAN Bus Wires (No. 4 Junction Connector - Steering Angle Sensor)".

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E74-3 (CANH) - E74-14 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E74-3 (CANH) - E74-14 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E74-3 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E74-14 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E74-3 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E74-14 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E74-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E74-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E74-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E74-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 52
OK


34. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)
C175844E12
  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E74-4 (CANH) - E74-15 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E74-4 (CANH) - E74-15 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E74-4 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E74-15 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E74-4 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E74-15 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E74-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E74-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E74-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E74-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 54
OK


35. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - SKID CONTROL ECU)
C175844E13
  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E74-5 (CANH) - E74-16 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E74-5 (CANH) - E74-16 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E74-5 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E74-16 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E74-5 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E74-16 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E74-5 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E74-16 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E74-5 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E74-16 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 56
OK


36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
C176202E13
  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E74-2 (CANH) - E74-13 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E74-2 (CANH) - E74-13 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E74-2 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E74-13 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E74-2 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E74-13 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E74-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E74-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E74-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E74-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 58
OK

REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR

37. CONNECT CONNECTOR
  1. Reconnect the E71 No. 7 junction connector connector.


NEXT


38. CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU)
C176207E01
  1. Disconnect the E42 seat belt control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E42-1 (CANH) - E42-2 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E42-1 (CANH) - E42-2 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E42-1 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E42-2 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E42-1 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E42-2 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E42-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E42-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E42-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E42-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SEAT BELT CONTROL ECU (CANH, CANL)
OK

REPLACE SEAT BELT CONTROL ECU (Click here)

39. CONNECT CONNECTOR
  1. Reconnect the E71 No. 7 junction connector connector.


NEXT


40. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)
C179402E02
  1. Disconnect the K39 No. 1 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    K39-1 (CANH) - K39-2 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    K39-1 (CANH) - K39-2 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    K39-1 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    K39-2 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    K39-1 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    K39-2 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    K39-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    K39-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    K39-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    K39-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 43
OK


41. CONNECT CONNECTOR
  1. Reconnect the E71 No. 7 junction connector connector.


NEXT


42. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
C176205E06
  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    K29-1 (CANH) - K29-2 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    K29-1 (CANH) - K29-2 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    K29-1 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    K29-2 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    K29-1 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    K29-2 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    K29-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    K29-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    K29-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    K29-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NO. 1 CAN JUNCTION CONNECTOR (CANH, CANL)
OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

43. CHECK FOR SHORT IN CAN BUS WIRES (SUSPENSION CONTROL ECU)

  1. C177542E01
    Disconnect the K34 suspension control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    K34-7 (CANH) - K34-8 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    K34-7 (CANH) - K34-8 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    K34-7 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    K34-8 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    K34-7 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    K34-8 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    K34-7 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    K34-8 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    K34-7 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    K34-8 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SUSPENSION CONTROL ECU (CANH, CANL)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)

44. CONNECT CONNECTOR
  1. Reconnect the F21 No. 6 junction connector connector.


NEXT


45. CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU)
C176206E01
  1. Disconnect the F12 clearance warning ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    F12-3 (CANH) - F12-5 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    F12-3 (CANH) - F12-5 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    F12-3 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    F12-5 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    F12-3 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    F12-5 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    F12-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    F12-5 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    F12-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    F12-5 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU (CANH, CANL)
OK

REPLACE CLEARANCE WARNING ECU ASSEMBLY (Click here)

46. CONNECT CONNECTOR
  1. Reconnect the F21 No. 6 junction connector connector.


NEXT


47. CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU)

  1. C177232E01
    Disconnect the F43 parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    F43-9 (CANH) - F43-10 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    F43-9 (CANH) - F43-10 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    F43-9 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    F43-10 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    F43-9 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    F43-10 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    F43-9 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    F43-10 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    F43-9 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    F43-10 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE TO PARKING ASSIST ECU (CANH, CANL)
OK

REPLACE PARKING ASSIST ECU (Click here)

48. CONNECT CONNECTOR
  1. Reconnect the E68 No. 5 junction connector connector.


NEXT


49. CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR)
C176208E01
  1. Disconnect the E50 yaw rate sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E50-3 (CANH) - E50-2 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E50-3 (CANH) - E50-2 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E50-3 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E50-2 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E50-3 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E50-2 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E50-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E50-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E50-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E50-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)
OK

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)

50. CONNECT CONNECTOR
  1. Reconnect the E74 No. 4 junction connector connector.


NEXT


51. CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)
C176209E01
  1. Disconnect the A27 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    A27-19 (CAN+) - A29-20 (CAN-)
    Ignition switch off
    1 Ω or higher
    OK
    A27-19 (CAN+) - A29-20 (CAN-)
    Ignition switch off
    Below 1 Ω
    NG
    A27-19 (CAN+) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    A29-20 (CAN-) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    A27-19 (CAN+) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    A29-20 (CAN-) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    A27-19 (CAN+) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    A29-20 (CAN-) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    A27-19 (CAN+) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    A29-20 (CAN-) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CAN+, CAN-)
OK

REPLACE 4WD CONTROL ECU (Click here)

52. CONNECT CONNECTOR
  1. Reconnect the E74 No. 4 junction connector connector.


NEXT


53. CHECK FOR SHORT IN CAN BUS WIRES (STEERING CONTROL ECU)

  1. C177231E01
    Disconnect the E79 suspension control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E79-9 (CANH) - E79-20 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E79-9 (CANH) - E79-20 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E79-9 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E79-20 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E79-9 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E79-20 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E79-9 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E79-20 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E79-9 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E79-20 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING CONTROL ECU (CANH, CANL)
OK

REPLACE STEERING CONTROL ECU (Click here)

54. CONNECT CONNECTOR
  1. Reconnect the E74 No. 4 junction connector connector.


NEXT


55. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)
C176203E01
  1. Disconnect the E11 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E11-10 (CANH) - E11-9 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E11-10 (CANH) - E11-9 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E11-10 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E11-9 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E11-10 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E11-9 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E11-10 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E11-9 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E11-10 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E11-9 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR (Click here)

56. CONNECT CONNECTOR
  1. Reconnect the E74 No. 4 junction connector connector.


NEXT


57. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
C176204E01
  1. Disconnect the A24 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    A24-11 (CANH) - A24-25 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    A24-11 (CANH) - A24-25 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    A24-11 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    A24-25 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    A24-11 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    A24-25 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    A24-11 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    A24-25 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    A24-11 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    A24-25 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

58. CONNECT CONNECTOR
  1. Reconnect the E74 No. 4 junction connector connector.


NEXT


59. CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)
C176210E01
  1. Disconnect the E31 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    1 Ω or higher
    OK
    E31-13 (CA2H) - E31-12 (CA2L)
    Ignition switch off
    Below 1 Ω
    NG
    E31-13 (CA2H) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E31-12 (CA2L) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E31-13 (CA2H) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E31-12 (CA2L) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E31-13 (CA2H) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E31-12 (CA2L) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E31-13 (CA2H) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E31-12 (CA2L) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CA2H, CA2L)
OK

REPLACE NETWORK GATEWAY ECU (Click here)

60. CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)
C136761E07
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the E31 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E31-4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E31-2 (BATT) - Body ground
    Always
    11 to 14 V
    E31-9 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V
    E31-10 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NETWORK GATEWAY ECU (Click here)


← U1002 (CAN MS BUS) Lost Communication with Gateway Module (Main body ECU) (from Jan 2012)U1002 (CAN No. 2 BUS) Lost Communication with Gateway Module (Network Gateway ECU) (from Jan 2012) →