U1002 (CAN No. 2 BUS) Lost Communication with Gateway Module (Network Gateway ECU)
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
- The network gateway ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN movement control bus.
- When the network gateway ECU receives a response signal from the ECUs connected to the CAN movement control bus, the network gateway ECU recognizes and memorizes that the ECU is connected to the CAN movement control bus. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to the CAN movement control bus when communicating with those ECUs. If the network gateway ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN movement control bus, the network gateway ECU determines that a malfunction exists.
- If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
| DTC Code |
DTC Detection Condition |
Trouble Area |
| U1002 (CAN No. 2 BUS) |
Lost communication with the gateway module (network gateway ECU). |
|
- *1: for 1VD-FTV with DPF
- *2: w/ Vehicle Stability Control System
- *3: w/ Dynamic Radar Cruise Control System
- *4: w/ Pre-crash Safety System
- *5: w/ Side Monitor System
- *6: w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System
- *7: w/ Variable Gear Ratio Steering System
- *8: w/ Active Height Control Suspension System
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| NEXT | |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
- CAUTION:
- For vehicles with an SRS system:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| NEXT | |
| 3. CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT CIRCUIT) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
Resistance Malfunction
E31-13 (CA2H) - E31-12 (CA2L)
Ignition switch off
54 to 69 Ω
Below 53 Ω: Short in line
E31-13 (CA2H) - E31-12 (CA2L)
Ignition switch off
54 to 69 Ω
70 Ω or higher: Open in CAN main bus line
E31-13 (CA2H) - E31-2 (BATT)
Ignition switch off
6 kΩ or higher
Below 6 kΩ: +B short
E31-12 (CA2L) - E31-2 (BATT)
Ignition switch off
6 kΩ or higher
Below 6 kΩ: +B short
E31-13 (CA2H) - E31-4 (GND)
Ignition switch off
200 Ω or higher
Below 200 Ω: Ground short
E31-12 (CA2L) - E31-4 (GND)
Ignition switch off
200 Ω or higher
Below 200 Ω: Ground short
Text in Illustration *a
Component with harness connected
(Network Gateway ECU)
Result Result
Proceed to
NG - Open in CAN main wire
A
NG - Short in line
- +B short
- Ground short
B
OK
C
|
|
||||
|
|
||||
| A | |
| 4. CHECK FOR OPEN IN MAIN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - NETWORK GATEWAY ECU) |
Disconnect the E71 No. 7 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E71-1 (CANH) - E71-12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 7 Junction Connector)
|
|
||||
| OK | |
| 5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 7 JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E71-3 (CANH) - E71-14 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 7 Junction Connector)
|
|
||||
| OK | ||
| ||
| 6. CONNECT CONNECTOR |
Reconnect the E71 No. 7 junction connector.
| NEXT | |
| 7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR) |
Disconnect the F73 No. 6 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
F73-6 (CANH) - F73-17 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 6 Junction Connector)
|
|
||||
| OK | |
| 8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NETWORK GATEWAY ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
F73-7 (CANH) - F73-18 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 6 Junction Connector)
|
|
||||
| OK | ||
| ||
| 9. CONNECT CONNECTOR |
Reconnect the F73 No. 6 junction connector.
| NEXT | |
| 10. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR) |
Disconnect the E68 No. 5 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E68-2 (CANH) - E68-13 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 5 Junction Connector)
|
|
||||
| OK | |
| 11. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 JUNCTION CONNECTOR - NETWORK GATEWAY ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E68-1 (CANH) - E68-12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 5 Junction Connector)
|
|
||||
| OK | ||
| ||
| 12. CONNECT CONNECTOR |
Reconnect the E68 No. 5 junction connector.
| NEXT | |
| 13. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR) |
Disconnect the E74 No. 4 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E74-1 (CANH) - E74-12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 4 Junction Connector)
|
|
||||
| OK | |
| 14. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E74-2 (CANH) - E74-13 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 4 Junction Connector)
|
|
||||
| OK | ||
| ||
| 15. CONNECT CONNECTOR |
Reconnect the E71 No. 7 junction connector.
| NEXT | |
| 16. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR) |
Disconnect the K29 No. 1 CAN junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
K29-1 (CANH) - K29-2 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
|
|
||||
| OK | ||
| ||
| 17. CONNECT CONNECTOR |
Reconnect the E74 No. 4 junction connector.
| NEXT | |
| 18. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NETWORK GATEWAY ECU - NO. 8 JUNCTION CONNECTOR) |
Disconnect the E31 network gateway ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E31-13 (CA2H) - E31-12 (CA2L)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to Network Gateway ECU)
|
|
||||
| OK | ||
| ||
| 19. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR SIDE) |
Disconnect the E71 No. 7 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E31-13 (CA2H) - E31-12 (CA2L)
Ignition switch off
108 to 132 Ω
E31-13 (CA2H) - E31-4 (GND)
Ignition switch off
200 Ω or higher
E31-12 (CA2L) - E31-4 (GND)
Ignition switch off
200 Ω or higher
E31-13 (CA2H) - E31-2 (BATT)
Ignition switch off
6 kΩ or higher
E31-12 (CA2L) - E31-2 (BATT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Component with harness connected
(Network Gateway ECU)
Result Tester Connection
Switch Condition
OK (for 1VD-FTV with DPF)
A
OK (except 1VD-FTV with DPF)
B
NG
C
|
|
||||
|
|
||||
| A | |
| 20. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E71-4 (CANH) - E71-15 (CANL)
Ignition switch off
200 Ω or higher
E71-4 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E71-15 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E71-4 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E71-15 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 7 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 21. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - SEAT BELT CONTROL ECU) |
- NOTICE:
- For vehicles without an pre-crash safety system, go to "Check for Short in CAN Bus Wires (No. 7 Junction Connector - No. 1 CAN Junction Connector)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E71-2 (CANH) - E71-13 (CANL)
Ignition switch off
200 Ω or higher
E71-2 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E71-13 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E71-2 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E71-13 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 7 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E71-3 (CANH) - E71-14 (CANL)
Ignition switch off
108 to 132 Ω
E71-3 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E71-14 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E71-3 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E71-14 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 7 Junction Connector)
*b
Front view of DLC3
Result Tester Connection
Switch Condition
OK
A
NG (w/ Active Height Control Suspension)
B
NG (w/o Active Height Control Suspension)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 23. CONNECT CONNECTOR |
Reconnect the E71 No. 7 junction connector.
| NEXT | |
| 24. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR) |
Disconnect the F73 No. 6 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
F73-6 (CANH) - F73-17 (CANL)
Ignition switch off
108 to 132 Ω
F73-6 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
F73-17 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
F73-6 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
F73-17 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 6 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 25. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E31-13 (CA2H) - E31-12 (CA2L)
Ignition switch off
108 to 132 Ω
E31-13 (CA2H) - E31-4 (GND)
Ignition switch off
200 Ω or higher
E31-12 (CA2L) - E31-4 (GND)
Ignition switch off
200 Ω or higher
E31-13 (CA2H) - E31-2 (BATT)
Ignition switch off
6 kΩ or higher
E31-12 (CA2L) - E31-2 (BATT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Component with harness connected
(Network Gateway ECU)
Result Result
Proceed to
OK (w/o TOYOTA Parking Assist-sensor System and w/o Side Monitor System)
A
OK (w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System)
B
OK (w/ Side Monitor System)
C
NG
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 26. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
F73-5 (CANH) - F73-16 (CANL)
Ignition switch off
200 Ω or higher
F73-5 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
F73-16 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
F73-5 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
F73-16 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 6 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 27. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - PARKING ASSIST ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
F73-5 (CANH) - F73-16 (CANL)
Ignition switch off
200 Ω or higher
F73-5 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
F73-16 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
F73-5 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
F73-16 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 6 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 28. CONNECT CONNECTOR |
Reconnect the F73 No. 6 junction connector.
| NEXT | |
| 29. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR) |
Disconnect the E68 No. 5 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E68-2 (CANH) - E68-13 (CANL)
Ignition switch off
108 to 132 Ω
E68-2 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E68-13 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E68-2 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E68-13 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 5 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 30. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR SIDE) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E31-13 (CA2H) - E31-12 (CA2L)
Ignition switch off
108 to 132 Ω
E31-13 (CA2H) - E31-4 (GND)
Ignition switch off
200 Ω or higher
E31-12 (CA2L) - E31-4 (GND)
Ignition switch off
200 Ω or higher
E31-13 (CA2H) - E31-2 (BATT)
Ignition switch off
6 kΩ or higher
E31-12 (CA2L) - E31-2 (BATT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Component with harness connected
(Network Gateway ECU)
|
|
||||
| OK | |
| 31. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY) |
- NOTICE:
- For vehicles without an vehicle stability control system, go to "Check for Short in CAN Bus Wires (No. 5 Junction Connector - Distance Control ECU Assembly)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E68-3 (CANH) - E68-14 (CANL)
Ignition switch off
200 Ω or higher
E68-3 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E68-14 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E68-3 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E68-14 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 5 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 32. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - DISTANCE CONTROL ECU ASSEMBLY) |
- NOTICE:
- For vehicles without an dynamic radar cruise control system, replace No. 5 junction connector..
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E68-4 (CANH) - E68-15 (CANL)
Ignition switch off
200 Ω or higher
E68-4 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E68-15 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E68-4 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E68-15 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 5 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 33. CONNECT CONNECTOR |
Reconnect the E68 No. 5 junction connector.
| NEXT | |
| 34. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR) |
Disconnect the E74 No. 4 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E74-1 (CANH) - E74-12 (CANL)
Ignition switch off
108 to 132 Ω
E74-1 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E74-12 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E74-1 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E74-12 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 4 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 35. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E74-6 (CANH) - E74-17 (CANL)
Ignition switch off
200 Ω or higher
E74-6 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E74-17 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E74-6 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E74-17 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 4 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - STEERING CONTROL ECU) |
- NOTICE:
- For vehicles without an variable gear ratio steering system, go to "Check for Short in CAN Bus Wires (No. 4 Junction Connector - Steering Angle Sensor)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E74-3 (CANH) - E74-14 (CANL)
Ignition switch off
200 Ω or higher
E74-3 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E74-14 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E74-3 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E74-14 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 4 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 37. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - STEERING ANGLE SENSOR) |
- NOTICE:
- For vehicles without an vehicle stability control system, go to "Check for Short in CAN Bus Wires (No. 4 Junction Connector - Skid Control ECU)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E74-4 (CANH) - E74-15 (CANL)
Ignition switch off
200 Ω or higher
E74-4 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E74-15 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E74-4 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E74-15 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 4 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 38. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - SKID CONTROL ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E74-5 (CANH) - E74-16 (CANL)
Ignition switch off
200 Ω or higher
E74-5 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E74-16 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E74-5 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E74-16 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 4 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 39. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E74-2 (CANH) - E74-13 (CANL)
Ignition switch off
108 to 132 Ω
E74-2 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E74-13 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E74-2 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E74-13 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 4 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 40. CONNECT CONNECTOR |
Reconnect the E71 No. 7 junction connector.
| NEXT | |
| 41. CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY) |
Disconnect the E102 power steering ECU assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E102-1 (CANH) - E102-2 (CANL)
Ignition switch off
54 to 69 Ω
E102-1 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E102-2 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E102-1 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E102-2 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Power Steering ECU Assembly)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 42. CONNECT CONNECTOR |
Reconnect the E71 No. 7 junction connector.
| NEXT | |
| 43. CHECK FOR SHORT IN CAN BUS WIRES (SEAT BELT CONTROL ECU) |
Disconnect the E42 seat belt control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E42-1 (CANH) - E42-2 (CANL)
Ignition switch off
54 to 69 Ω
E42-1 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E42-2 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E42-1 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E42-2 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Seat Belt Control ECU)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 44. CONNECT CONNECTOR |
Reconnect the E71 No. 7 junction connector.
| NEXT | |
| 45. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - SUSPENSION CONTROL ECU) |
Disconnect the K39 No. 1 CAN junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
K39-1 (CANH) - K39-2 (CANL)
Ignition switch off
200 Ω or higher
K39-1 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
K39-2 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
K39-1 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
K39-2 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 46. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR) |
Disconnect the K29 No. 1 CAN junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
K29-1 (CANH) - K29-2 (CANL)
Ignition switch off
108 to 132 Ω
K29-1 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
K29-2 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
K29-1 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
K29-2 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 47. CONNECT CONNECTOR |
Reconnect the K39 No. 1 CAN junction connector.
| NEXT | |
| 48. CHECK FOR SHORT IN CAN BUS WIRES (SUSPENSION CONTROL ECU) |
Disconnect the K34 suspension control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
K34-7 (CANH) - K34-8 (CANL)
Ignition switch off
54 to 69 Ω
K34-7 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
K34-8 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
K34-7 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
K34-8 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to Suspension Control ECU)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 49. CONNECT CONNECTOR |
Reconnect the E74 No. 7 junction connector.
| NEXT | |
| 50. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR) |
Disconnect the K29 No. 1 CAN junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
K29-1 (CANH) - K29-2 (CANL)
Ignition switch off
108 to 132 Ω
K29-1 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
K29-2 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
K29-1 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
K29-2 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 51. CONNECT CONNECTOR |
Reconnect the F73 No. 6 junction connector.
| NEXT | |
| 52. CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY) |
Disconnect the F12 clearance warning ECU assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
F12-3 (CANH) - F12-5 (CANL)
Ignition switch off
54 to 69 Ω
F12-3 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
F12-5 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
F12-3 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
F12-5 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 53. CONNECT CONNECTOR |
Reconnect the F73 No. 6 junction connector.
| NEXT | |
| Go to step 47 |
| 54. CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU) |
Disconnect the F76 parking assist ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
F76-40 (CANH) - F76-39 (CANL)
Ignition switch off
54 to 69 Ω
F76-40 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
F76-39 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
F76-40 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
F76-39 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to Parking Assist ECU)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 55. CONNECT CONNECTOR |
Reconnect the E68 No. 5 junction connector.
| NEXT | |
| 56. CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR ASSEMBLY) |
Disconnect the E50 yaw rate sensor assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E50-3 (CANH) - E50-2 (CANL)
Ignition switch off
54 to 69 Ω
E50-3 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E50-2 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E50-3 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E50-2 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Yaw Rate Sensor Assembly)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 57. CONNECT CONNECTOR |
Reconnect the E68 No. 5 junction connector.
| NEXT | |
| 58. CHECK FOR SHORT IN CAN BUS WIRES (DISTANCE CONTROL ECU ASSEMBLY) |
Disconnect the E108 distance control ECU assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E108-8 (CANH) - E108-9 (CANL)
Ignition switch off
54 to 69 Ω
E108-8 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E108-9 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E108-8 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E108-9 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to Distance Control ECU Assembly)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 59. CONNECT CONNECTOR |
Reconnect the E74 No. 4 junction connector.
| NEXT | |
| 60. CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU) |
Disconnect the A27 4WD control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A27-19 (CAN+) - A29-20 (CAN-)
Ignition switch off
54 to 69 Ω
A27-19 (CAN+) - E22-4 (CG)
Ignition switch off
200 Ω or higher
A29-20 (CAN-) - E22-4 (CG)
Ignition switch off
200 Ω or higher
A27-19 (CAN+) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
A29-20 (CAN-) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to 4WD Control ECU)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 61. CONNECT CONNECTOR |
Reconnect the E74 No. 4 junction connector.
| NEXT | |
| 62. CHECK FOR SHORT IN CAN BUS WIRES (STEERING CONTROL ECU) |
Disconnect the E79 suspension control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E79-9 (CANH) - E79-20 (CANL)
Ignition switch off
54 to 69 Ω
E79-9 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E79-20 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E79-9 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E79-20 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Steering Control ECU)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 63. CONNECT CONNECTOR |
Reconnect the E74 No. 4 junction connector.
| NEXT | |
| 64. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR) |
Disconnect the E11 steering angle sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E11-10 (CANH) - E11-9 (CANL)
Ignition switch off
54 to 69 Ω
E11-10 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E11-9 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E11-10 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E11-9 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Steering Angle Sensor)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 65. CONNECT CONNECTOR |
Reconnect the E74 No. 4 junction connector.
| NEXT | |
| 66. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU) |
Disconnect the A24 master cylinder solenoid (skid control ECU) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A24-11 (CANH) - A24-25 (CANL)
Ignition switch off
54 to 69 Ω
A24-11 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
A24-25 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
A24-11 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
A24-25 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 67. CONNECT CONNECTOR |
Reconnect the E74 No. 4 junction connector.
| NEXT | |
| 68. CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU) |
Disconnect the E31 network gateway ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E31-13 (CA2H) - E31-12 (CA2L)
Ignition switch off
54 to 69 Ω
E31-13 (CA2H) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E31-12 (CA2L) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E31-13 (CA2H) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E31-12 (CA2L) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to Network Gateway ECU)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 69. CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND) |
Connect the cable to the negative (-) battery terminal.

- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
Disconnect the E31 network gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E31-4 (GND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E31-2 (BATT) - Body ground
Always
11 to 14 V
E31-9 (IG2) - Body ground
Ignition switch ON
11 to 14 V
E31-10 (IG1) - Body ground
Ignition switch ON
11 to 14 V
| *a |
Rear view of wire harness connector (to Network Gateway ECU) |
|
|
||||
| OK | ||
| ||
