2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

Speaker Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The stereo component amplifier assembly sends a sound signal to the speakers.

WIRING DIAGRAM

C259383E01
C259382E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKERS)
  1. *1: for RH Side
  2. *2: for LH Side
  3. *3: for 14 Speakers
  4. *4: for 9 Speakers
  1. Disconnect the F74 stereo component amplifier assembly connector.

  1. Disconnect the I1*1 and/or I10*2 front No. 1 speaker assembly connector.

  1. Disconnect the F7*1 and/or F8*2 front No. 2 speaker assembly connector.

  1. Disconnect the F6 front No. 4 speaker assembly connector.

  1. Disconnect the J15*1 and/or J17*2 rear speaker set connector*4.

  1. Disconnect the J2*1 and/or J9*2 rear No. 3 speaker connector*3.

  1. Disconnect the S8*1 and/or S9*2 rear header speaker assembly connector*3.

  1. Disconnect the L4 No. 1 woofer box speaker connector.*3

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F74-5 (WFR+) - I1-1*1
    Always
    Below 1 Ω
    F74-20 (WFR-) - I1-2*1
    Always
    Below 1 Ω
    F74-4 (WFL+) - I10-1*2
    Always
    Below 1 Ω
    F74-19 (WFL-) - I10-2*2
    Always
    Below 1 Ω
    F74-13 (FR+) - F7-1 (+)*1
    Always
    Below 1 Ω
    F74-28 (FR-) - F7-3 (-)*1
    Always
    Below 1 Ω
    F74-12 (FL+) - F8-1 (+)*2
    Always
    Below 1 Ω
    F74-27 (FL-) - F8-2 (-)*2
    Always
    Below 1 Ω
    F74-7 (CTR+) - F6-1
    Always
    Below 1 Ω
    F74-22 (CTR-) - F6-2
    Always
    Below 1 Ω
    F74-15 (RR+) - J15-1*1, *4
    Always
    Below 1 Ω
    F74-30 (RR-) - J15-2*1, *4
    Always
    Below 1 Ω
    F74-14 (RL+) - J17-1*2, *4
    Always
    Below 1 Ω
    F74-29 (RL-) - J17-2*2, *4
    Always
    Below 1 Ω
    F74-15 (R-R+) - J2-1 (+)*1, *3
    Always
    Below 1 Ω
    F74-30 (R-R) - J2-3 (-)*1, *3
    Always
    Below 1 Ω
    F74-14 (R-L+) - J9-1 (+)*2, *3
    Always
    Below 1 Ω
    F74-29 (R-L-) - J9-3 (-)*2, *3
    Always
    Below 1 Ω
    F74-11 (SR+) - S8-1 (RRD+)*1, *3
    Always
    Below 1 Ω
    F74-26 (SR-) - S8-2 (RRD-)*1, *3
    Always
    Below 1 Ω
    F74-10 (SL+) - S9-1 (RLD+)*2, *3
    Always
    Below 1 Ω
    F74-25 (SL-) - S9-2 (RLD-)*2, *3
    Always
    Below 1 Ω
    F74-6 (WF1+) - L4-1 (WF1+)*3
    Always
    Below 1 Ω
    F74-21 (WF1-) - L4-2 (WF1-)*3
    Always
    Below 1 Ω
    F74-8 (WF2+) - L4-3 (WF2+)*3
    Always
    Below 1 Ω
    F74-23 (WF2-) - L4-4 (WF2-)*3
    Always
    Below 1 Ω
    F74-5 (WFR+) - Body ground
    Always
    10 kΩ or higher
    F74-20 (WFR-) - Body ground
    Always
    10 kΩ or higher
    F74-4 (WFL+) - Body ground
    Always
    10 kΩ or higher
    F74-19 (WFL-) - Body ground
    Always
    10 kΩ or higher
    F74-13 (FR+) - Body ground
    Always
    10 kΩ or higher
    F74-28 (FR-) - Body ground
    Always
    10 kΩ or higher
    F74-12 (FL+) - Body ground
    Always
    10 kΩ or higher
    F74-27 (FL-) - Body ground
    Always
    10 kΩ or higher
    F74-7 (CTR+) - Body ground
    Always
    10 kΩ or higher
    F74-22 (CTR-) - Body ground
    Always
    10 kΩ or higher
    F74-15 (RR+) - Body ground
    Always
    10 kΩ or higher
    F74-30 (RR-) - Body ground
    Always
    10 kΩ or higher
    F74-14 (RL+) - Body ground
    Always
    10 kΩ or higher
    F74-29 (RL-) - Body ground
    Always
    10 kΩ or higher
    F74-15 (R-R+) - Body ground
    Always
    10 kΩ or higher
    F74-30 (R-R) - Body ground
    Always
    10 kΩ or higher
    F74-14 (R-L+) - Body ground
    Always
    10 kΩ or higher
    F74-29 (R-L-) - Body ground
    Always
    10 kΩ or higher
    F74-11 (SR+) - Body ground
    Always
    10 kΩ or higher
    F74-26 (SR-) - Body ground
    Always
    10 kΩ or higher
    F74-10 (SL+)- Body ground
    Always
    10 kΩ or higher
    F74-25 (SL-) - Body ground
    Always
    10 kΩ or higher
    F74-6 (WF1+) - Body ground
    Always
    10 kΩ or higher
    F74-21 (WF1-) - Body ground
    Always
    10 kΩ or higher
    F74-8 (WF2+) - Body ground
    Always
    10 kΩ or higher
    F74-23 (WF2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

  1. E192950
    Disconnect the front No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 14 Speakers 
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω
    for 9 Speakers 
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3 Ω

    Result 
    Result
    Proceed to
    OK (for 14 Speakers)
    A
    OK (for 9 Speakers)
    B
    NG
    C



B
Go to step 5

C
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
A


3. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

  1. E192487E02
    Disconnect the front No. 2 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 2 (TWR+)
    Always
    Below 1 Ω
    3 (-) - 4 (TWR-)
    Always
    Below 1 Ω
    2 (TWR+) - 4 (TWR-)
    Always
    1.5 to 2.5 Ω
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 2 (TWL+)
    Always
    Below 1 Ω
    3 (-) - 4 (TWL-)
    Always
    Below 1 Ω
    2 (TWL+) - 4 (TWL-)
    Always
    1.5 to 2.5 Ω

    Text in Illustration 
    *A
    for RH Side
    *B
    for LH Side



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4. CHECK FRONT NO. 3 SPEAKER ASSEMBLY
  1. Temporarily replace the front No. 3 speaker assembly with a new or normally functioning one (Click here).

  1. Check for DTCs and check if the same DTCs is output (Click here).

    OK:
    No DTCs are output.



NG
Go to step 7
OK

END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

5. CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Temporarily replace the front No. 2 speaker assembly with a new or normally functioning one (Click here).

  1. Check for DTCs and check if the same DTCs is output (Click here).

    OK:
    No DTCs are output.



NG
Go to step 6
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

6. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY

  1. E192488E02
    Disconnect the front No. 3 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (-) - 2 (+)
    Always
    4 Ω



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 3 SPEAKER)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the F7*1 and/or F8*2 front No. 2 speaker assembly connector.

  1. Disconnect the F13*1 and/or F14*2 front No. 3 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    F7-2 (TWR+) - F13-1
    Always
    Below 1 Ω
    F7-4 (TWR-) - F13-2
    Always
    Below 1 Ω
    F7-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    F7-4 (TWR-) - Body ground
    Always
    10 kΩ or higher
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    F8-2 (TWL+) - F14-1
    Always
    Below 1 Ω
    F8-4 (TWL-) - F14-2
    Always
    Below 1 Ω
    F8-2 (TWL+) - Body ground
    Always
    10 kΩ or higher
    F8-4 (TWL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT FRONT NO. 4 SPEAKER ASSEMBLY

  1. E192485
    Disconnect the front No. 4 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 14 Speakers 
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.5 Ω
    for 9 Speakers 
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    6 Ω



NG
REPLACE FRONT NO. 4 SPEAKER ASSEMBLY (Click here)
OK


9. INSPECT REAR SPEAKER SET

  1. E192950E03
    Disconnect the rear speaker set connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 14 Speakers 
    Tester Connection
    Condition
    Specified Condition
    1 (WF+) - 2 (WF-)
    Always
    1.5 to 2.3 Ω
    for 9 Speakers (for FUJITSU TEN Made) 
    Tester Connection
    Condition
    Specified Condition
    1 (WF+) - 2 (WF-)
    Always
    4 Ω
    for 9 Speakers (for PIONEER Made) 
    Tester Connection
    Condition
    Specified Condition
    1 (WF+) - 2 (WF-)
    Always
    5 Ω

    Result 
    Result
    Proceed to
    OK (for 14 Speakers)
    A
    OK (for 9 Speakers)
    B
    NG
    C



B
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

C
REPLACE REAR SPEAKER SET (Click here)
A


10. CHECK HARNESS AND CONNECTOR (REAR NO. 3 SPEAKER - REAR SPEAKER SET)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the J2*1 and/or J9*2 front No. 3 speaker assembly connector.

  1. Disconnect the J18*1 and/or J19*2 rear speaker set connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    J2-2 (+) - J18-1 (WF+)
    Always
    Below 1 Ω
    J2-4 (-) - J18-2 (WF-)
    Always
    Below 1 Ω
    J2-2 (+) - Body ground
    Always
    10 kΩ or higher
    J2-4 (-) - Body ground
    Always
    10 kΩ or higher
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    J9-2 (+) - J19-1 (WF+)
    Always
    Below 1 Ω
    J9-4 (-) - J19-2 (WF-)
    Always
    Below 1 Ω
    J9-2 (+) - Body ground
    Always
    10 kΩ or higher
    J9-4 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. INSPECT REAR HEADER SPEAKER ASSEMBLY

  1. E192485E03
    Disconnect the rear header assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    1 (RRD+) - 2 (RRD-)
    Always
    1.5 to 2.5 Ω
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    1 (RLD+) - 2 (RLD-)
    Always
    1.5 to 2.5 Ω

    Text in Illustration 
    *A
    for RH Side
    *B
    for LH Side



NG
REPLACE REAR HEADER SPEAKER ASSEMBLY (Click here)
OK


12. CHECK REAR NO. 3 SPEAKER ASSEMBLY
  1. Temporarily replace the rear No. 3 speaker assembly with a new or normally functioning one (Click here).

  1. Check for DTCs and check if the same DTCs is output (Click here).

    OK:
    No DTCs are output.



NG
Go to step 13
OK

END (REAR NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

13. INSPECT NO. 1 WOOFER BOX SPEAKER ASSEMBLY

  1. E192489E02
    Disconnect the No. 1 woofer box speaker assembly speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    1 (WF1+) - 2 (WF1-)
    Always
    1.6 to 2.4 Ω
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    3 (WF2+) - 4 (WF2-)
    Always
    1.6 to 2.4 Ω



NG
REPLACE NO. 1 WOOFER BOX SPEAKER (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)


← Speaker Circuit (Sep 2011 – Dec 2011)Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier (from Jan 2012) →