2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

Speaker Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The stereo component amplifier assembly sends a sound signal to the speakers.

WIRING DIAGRAM

E155742E05
E192482E02
E192483E02

INSPECTION PROCEDURE


1. CHECK SPEAKER
  1. Check the malfunctioning speakers.

    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 11
A


2. CHECK SPEAKER
  1. Check the malfunctioning speakers.

    Result 
    Result
    Proceed to
    Front No. 1 speaker
    A
    Front No. 2 speaker
    B
    Front No. 3 speaker
    C
    Front No. 4 speaker
    D



B
Go to step 5

C
Go to step 7

D
Go to step 9
A


3. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

  1. E192484E01
    Disconnect the I1 and I10 front No. 1 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 1 SPEAKER)
  1. Disconnect the I1 and I10 front No. 1 speaker connectors.

  1. Disconnect the F3 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    F3-1 (WFL+) - I10-1
    Always
    Below 1 Ω
    F3-5 (WFL-) - I10-2
    Always
    Below 1 Ω
    F3-1 (WFL+) - Body ground
    Always
    10 kΩ or higher
    F3-5 (WFL-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    F3-2 (WFR+) - I1-1
    Always
    Below 1 Ω
    F3-6 (WFR-) - I1-2
    Always
    Below 1 Ω
    F3-2 (WFR+) - Body ground
    Always
    10 kΩ or higher
    F3-6 (WFR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

5. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

  1. E192487E01
    Disconnect the F8 and F7 front No. 2 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Below 1 Ω
    3 - 4
    Always
    Below 1 Ω
    2 - 4
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 2 SPEAKER)
  1. Disconnect the F7 and F8 front No. 2 speaker connectors.

  1. Disconnect the F52 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    F52-3 (FL+) - F8-1 (+)
    Always
    Below 1 Ω
    F52-8 (FL-) - F8-3 (-)
    Always
    Below 1 Ω
    F52-3 (FL+) - Body ground
    Always
    10 kΩ or higher
    F52-8 (FL-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    F52-10 (FR+) - F7-1 (+)
    Always
    Below 1 Ω
    F52-9 (FR-) - F7-3 (-)
    Always
    Below 1 Ω
    F52-10 (FR+) - Body ground
    Always
    10 kΩ or higher
    F52-9 (FR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

7. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY

  1. E192488E01
    Disconnect the F14 and F13 front No. 3 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 3 Speaker Assembly)



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


8. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

  1. E192487E01
    Disconnect the F8 and F7 front No. 2 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Below 1 Ω
    3 - 4
    Always
    Below 1 Ω
    2 - 4
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

9. INSPECT FRONT NO. 4 SPEAKER ASSEMBLY

  1. E192485E01
    Disconnect the F6 front No. 4 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    6 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 4 Speaker Assembly)



NG
REPLACE FRONT NO.4 SPEAKER ASSEMBLY (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 4 SPEAKER)
  1. Disconnect the F6 front No. 4 speaker connector.

  1. Disconnect the F3 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 9 Speaker Model:
    Tester Connection
    Condition
    Specified Condition
    F3-8 (CTR+) - F6-1
    Always
    Below 1 Ω
    F3-7 (CTR-) - F6-2
    Always
    Below 1 Ω
    F3-8 (CTR+) - Body ground
    Always
    10 kΩ or higher
    F3-7 (CTR-) - Body ground
    Always
    10 kΩ or higher
    for 14 Speaker Model:
    Tester Connection
    Condition
    Specified Condition
    F3-3 (CTR+) - F6-1
    Always
    Below 1 Ω
    F3-9 (CTR-) - F6-2
    Always
    Below 1 Ω
    F3-3 (CTR+) - Body ground
    Always
    10 kΩ or higher
    F3-9 (CTR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

11. CHECK SPEAKER
  1. Check the malfunctioning speakers.

    Result 
    Result
    Proceed to
    Rear speaker set
    A
    Rear No. 3 speaker*1
    B
    Rear header speaker*1
    C
    No. 1 woofer box speaker*1
    D
    *1: for 14 speaker



B
Go to step 17

C
Go to step 19

D
Go to step 21
A


12. SYSTEM CHECK
  1. Check the vehicle specifications.

    Result 
    Result
    Proceed to
    for 9 speakers model
    A
    for 14 speakers model
    B



B
Go to step 15
A


13. INSPECT REAR SPEAKER SET

  1. E192486E01
    Disconnect the J17 and J15 rear speaker set connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Rear Speaker Set)



NG
REPLACE REAR SPEAKER SET (Click here)
OK


14. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - REAR SPEAKER SET)
  1. Disconnect the J15 and J17 rear speaker set connectors.

  1. Disconnect the F52 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    F52-4 (RL+) - J17-1
    Always
    Below 1 Ω
    F52-11 (RL-) - J17-2
    Always
    Below 1 Ω
    F52-4 (RL+) - Body ground
    Always
    10 kΩ or higher
    F52-11 (RL-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    F52-5 (RR+) - J15-1
    Always
    Below 1 Ω
    F52-12 (RR-) - J15-2
    Always
    Below 1 Ω
    F52-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    F52-12 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

15. INSPECT REAR SPEAKER SET

  1. E192486E01
    Disconnect the J18 and J19 rear speaker set connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.3 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Rear Speaker Set)



NG
REPLACE REAR SPEAKER SET (Click here)
OK


16. INSPECT REAR NO. 3 SPEAKER ASSEMBLY

  1. E192490E01
    Disconnect the J2 and J9 rear No. 3 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Below 1 Ω
    3 - 4
    Always
    Below 1 Ω
    2 - 4
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 3 Speaker Assembly)



NG
REPLACE REAR NO. 3 SPEAKER ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

17. INSPECT REAR NO. 3 SPEAKER ASSEMBLY

  1. E192490E01
    Disconnect the J2 and J9 rear No. 3 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Below 1 Ω
    3 - 4
    Always
    Below 1 Ω
    2 - 4
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Rear No. 3 Speaker Assembly)



NG
REPLACE REAR NO. 3 SPEAKER ASSEMBLY (Click here)
OK


18. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 3 SPEAKER)
  1. Disconnect the J2 and J9 rear No. 3 speaker connectors.

  1. Disconnect the F52 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    F52-4 (R-L+) - J9-1
    Always
    Below 1 Ω
    F52-11 (R-L-) - J9-3
    Always
    Below 1 Ω
    F52-4 (R-L+) - Body ground
    Always
    10 kΩ or higher
    F52-11 (R-L-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    F52-5 (R-R+) - J2-1
    Always
    Below 1 Ω
    F52-12 (R-R-) - J2-3
    Always
    Below 1 Ω
    F52-5 (R-R+) - Body ground
    Always
    10 kΩ or higher
    F52-12 (R-R-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

19. INSPECT REAR HEADER SPEAKER

  1. E192485E01
    Disconnect the S8 and S9 rear header speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.5 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Rear Header Speaker)



NG
REPLACE REAR HEADER SPEAKER (Click here)
OK


20. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - REAR HEADER SPEAKER)
  1. Disconnect the S8 and S9 rear header speaker connectors.

  1. Disconnect the F3 and F52 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    F3-8 (SL+) - S9-1
    Always
    Below 1 Ω
    F3-7 (SL-) - S9-2
    Always
    Below 1 Ω
    F3-8 (SL+) - Body ground
    Always
    10 kΩ or higher
    F3-7 (SL-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    F52-2 (SR+) - S8-1
    Always
    Below 1 Ω
    F52-7 (SR-) - S8-2
    Always
    Below 1 Ω
    F52-2 (SR+) - Body ground
    Always
    10 kΩ or higher
    F52-7 (SR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

21. INSPECT NO. 1 WOOFER BOX SPEAKER

  1. E192489E01
    Disconnect the L4 No. 1 woofer box speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.6 to 2.4 Ω
    3 - 4
    Always
    1.6 to 2.4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (No. 1 woofer box speaker)



NG
REPLACE NO. 1 WOOFER BOX SPEAKER (Click here)
OK


22. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - BOX SPEAKER)
  1. Disconnect the L4 No. 1 woofer box speaker connector.

  1. Disconnect the F3 and F52 stereo component amplifier assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F52-1 (WF1+) - L4-1
    Always
    Below 1 Ω
    F52-6 (WF1-) - L4-2
    Always
    Below 1 Ω
    F3-4 (WF2+) - L4-3
    Always
    Below 1 Ω
    F3-10 (WF2-) - L4-4
    Always
    Below 1 Ω
    F52-1 (WF1+) - Body ground
    Always
    10 kΩ or higher
    F52-6 (WF1-) - Body ground
    Always
    10 kΩ or higher
    F3-4 (WF2+) - Body ground
    Always
    10 kΩ or higher
    F3-10 (WF2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)


← Illumination Circuit (from Jan 2012)Speaker Circuit (from Jan 2012) →