Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0340  Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet, iron core and pickup coil.

The G signal plate (timing sprocket) has one tooth on its outer circumference and is installed on the camshaft timing chain gear. When the timing gear rotates, the protrusion on the signal plate and the air gap on the pickup coil change, causing fluctuations in the magnetic field that generate a voltage in the pickup coil.

The NE signal plate has 34 teeth and is mounted on the crank angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the standard crankshaft angle based on the G signal, and detects the actual crankshaft angle and engine speed based on the NE signal.

P0340
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Crank engine for 4 seconds (STA on) STA on:
No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more (2 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

No. 2 camshaft timing sprocket

·

ECM


Idle engine for 1 second (STA off) STA off:
When either condition below is met for 1 second (1 trip detection logic):
·

G signal is not input with an engine speed of 500 rpm or more.

·

No camshaft position sensor signal is sent to the ECM with an engine speed of 500 to 3000 rpm 20 times or more.



HINT:

If DTC P0340 is stored, the following symptoms may appear:

- Difficult starting

- Misfire

- Combustion noise

- Black smoke

- White smoke

- Lack of power



CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT CAMSHAFT POSITION SENSOR
a.
A165742E01
0.163,0.134 2.656,0.491 2.493,0.357 10 Component without harness connected: (Camshaft Position Sensor)

Disconnect the camshaft position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Cold 835 to 1400 Ω
1 - 2 Hot 1060 to 1645 Ω


HINT:

In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).




OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

6.REPLACE CAMSHAFT POSITION SENSOR
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.

A385132E01
1.625,0.917 2.042,1.156 0.417,0.24 4.01,0.917 4.427,1.156 0.417,0.24 4.75,0.917 5.167,1.156 0.417,0.24 4.688,2.25 4.938,1.802 true 5.271,2.26 5,1.802 true 0.594,0.104 2.927,0.479 2.333,0.375 10 false Front view of wire harness connector: (to Camshaft Position Sensor) 3.719,0.083 6.052,0.458 2.333,0.375 10 false Front view of wire harness connector: (to ECM) 1.688,0.958 2.031,1.135 0.344,0.177 10 false C66 4.094,0.948 4.438,1.125 0.344,0.177 10 false C45 4.479,0.844 4.823,1.021 0.344,0.177 10 false *1 4.823,0.948 5.167,1.125 0.344,0.177 10 false C46 5.219,0.854 5.563,1.031 0.344,0.177 10 false *2 4.531,2.281 5.063,2.49 0.531,0.208 10 false 79 (G-) 5.208,2.271 5.74,2.479 0.531,0.208 10 false 80 (G+) 0.302,1.969 1.146,2.177 0.844,0.208 10 false *1: for LHD 0.292,2.344 1.135,2.552 0.844,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
C66-1 - C45-80 (G+) Always Below 1 Ω
C66-2 - C45-79 (G-) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C66-1 - C46-80 (G+) Always Below 1 Ω
C66-2 - C46-79 (G-) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C66-1 or C45-80 (G+) - Body ground Always 10 kΩ or higher
C66-2 or C45-79 (G-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C66-1 or C46-80 (G+) - Body ground Always 10 kΩ or higher
C66-2 or C46-79 (G-) - Body ground Always 10 kΩ or higher




OK

3.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
A366136E03
0.479,1.667 0.802,1.854 0.323,0.188 10 false OK 2.677,1.792 3.01,2 0.333,0.208 10 false NG

Check the sensor installation.

OK:

Sensor is installed correctly.




OK

4.CHECK NO. 2 CAMSHAFT TIMING SPROCKET

NG

8.SECURELY REINSTALL SENSOR
4.CHECK NO. 2 CAMSHAFT TIMING SPROCKET
a.

Check the condition of the timing sprocket.

OK:

Timing sprocket does not have any cracks or deformation.




OK

5.REPLACE ECM

NG

9.REPLACE NO. 2 CAMSHAFT TIMING SPROCKET
5.REPLACE ECM

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE CAMSHAFT POSITION SENSOR
a.


NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.SECURELY REINSTALL SENSOR

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE NO. 2 CAMSHAFT TIMING SPROCKET
a.

Replace the No. 2 camshaft timing sprocket (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Start the engine and idle it for 2 seconds.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END