1.DISCHARGE FUEL SYSTEM PRESSURE
2. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
53292A
4.REMOVE UPPER RADIATOR SUPPORT SEAL
53111
5.REMOVE RADIATOR GRILLE
52119A
6.REMOVE FRONT BUMPER COVER
32917
7.REMOVE TRANSMISSION OIL COOLER AIR DUCT
53294C
8.DISCONNECT RADIATOR SIDE DEFLECTOR LH
55781E
9.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53737B
10.REMOVE FRONT FENDER APRON SEAL LH
53736G
11.REMOVE FRONT FENDER APRON SEAL FRONT RH
53806
12.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53805
13.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
51405C
14.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
51442
15.REMOVE NO. 2 ENGINE UNDER COVER
16.DRAIN ENGINE OIL
17.DRAIN ENGINE COOLANT
11209
18.REMOVE V-BANK COVER SUB-ASSEMBLY
17880
19.REMOVE AIR CLEANER HOSE ASSEMBLY
17700
20.REMOVE AIR CLEANER ASSEMBLY
16400
21.REMOVE RADIATOR ASSEMBLY
22.DISCONNECT ENGINE WIRE
Engine Room LH Side:
Remove the engine room relay block cover.
Disconnect the 2 connectors and 2 clips from the engine room junction block.
Disconnect the injector connector.
Disconnect the 4 ignition coil connectors.
Disconnect the 2 VVT sensor connectors.
Disconnect the 4 clamps.
Remove the 2 bolts and ground wire.
Disconnect the noise filter connector.
Disconnect the engine coolant temperature sensor connector.
Disconnect the 2 camshaft timing oil control valve connectors.
Disconnect the camshaft position sensor connector.
Disconnect the 3 clamps.
Disconnect the cooler compressor connector.
Engine Room RH Side:
Disconnect the 2 camshaft timing oil control valve connectors.
Disconnect the 4 ignition coil connectors.
Disconnect the injector connector.
Disconnect the 2 VVT sensor connectors.
Disconnect the noise filter connector.
Remove the 2 bolts and ground wire.
Disconnect the throttle position sensor and throttle control motor connector.
Disconnect the 5 clamps.
Disconnect the 2 clamps and power steering oil pressure switch connector.
23.DISCONNECT WATER PIPE AND HOSE SUB-ASSEMBLY
Disconnect the 3 hoses.
Remove the 2 bolts and disconnect the water pipe and hose from the cylinder head cover.
88320
24.DISCONNECT COOLER COMPRESSOR ASSEMBLY
Remove the 3 bolts, nut and stud bolt, and disconnect the cooler compressor.
It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.
23902
25.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY
Remove the 2 bolts and disconnect the fuel tube.
| *A | LH Side |
| *B | RH Side |
26.REMOVE OIL FILTER ELEMENT
11452
27.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
83520
28.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY
16207
29.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the 3 bolts.
Disconnect the 4 hoses and remove the water by-pass pipe.
15781
30.REMOVE NO. 1 OIL COOLER BRACKET
15671
31.REMOVE OIL FILTER BRACKET
17111
32.REMOVE INTAKE MANIFOLD
44310
33.DISCONNECT VANE PUMP ASSEMBLY
Remove the 2 bolts and disconnect the vane pump.
32907A
34.DISCONNECT OIL COOLER PIPE ASSEMBLY
27020
35.REMOVE GENERATOR ASSEMBLY
16261G
36.REMOVE NO. 1 WATER BY-PASS HOSE
Remove the No. 1 water by-pass hose by disconnecting the hose from the water inlet housing and front water by-pass joint.
16206
37.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
Disconnect the 2 hoses.
Remove the 2 bolts and water by-pass pipe.
16355
38.REMOVE FRONT WATER BY-PASS JOINT
Disconnect the No. 2 water by-pass hose from the water by-pass joint.
Remove the 4 nuts, water by-pass joint and 2 gaskets.
11212
39.REMOVE NO. 2 ENGINE COVER
12611
40.REMOVE NO. 1 ENGINE COVER
16323
41.REMOVE WATER INLET HOUSING
Remove the 3 bolts, water inlet housing and gasket.
16173
42.REMOVE WATER PUMP PULLEY
Using SST, hold the water pump pulley.
Remove the 4 bolts and water pump pulley.
16603
43.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
Remove the bolt and idler pulley.
16211
44.REMOVE FLUID COUPLING BRACKET
Remove the 4 bolts and fluid coupling bracket.
16620
45.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the standard bolt, 6 mm hexagon wrench bolt and belt tensioner.
19500
46.REMOVE IGNITION COIL ASSEMBLY
Remove the 8 bolts and 8 ignition coils.
11202
47.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
Remove the 14 bolts, seal washer, cylinder head cover and gasket.
Make sure the removed parts are returned to the same places they were removed from.
Remove the 5 gaskets from the camshaft bearing caps (No. 2, No. 3).
11201
48.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH
Remove the bolt and noise filter.
Remove the 14 bolts, seal washer, cylinder head cover and gasket.
Make sure the removed parts are returned to the same places they were removed from.
Remove the 5 gaskets from the camshaft bearing caps (No. 1, No. 3).
11193
49.REMOVE SPARK PLUG TUBE GASKET
13471
50.REMOVE CRANKSHAFT PULLEY
Using SST, loosen the crankshaft pulley set bolt until 2 or 3 threads are engaged.
| *a | Hold |
|
Turn |
Using the pulley set bolt and SST, remove the crankshaft pulley.
| *a | Hold |
|
Turn |
51.DISCONNECT WIRE HARNESS CLAMP BRACKET
Remove the bolt and disconnect the bracket.
13521A
52.REMOVE CRANKSHAFT TIMING GEAR KEY
Using a screwdriver, remove the timing gear key from the crankshaft.
11302
53.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 28 bolts and nut shown in the illustration.
|
Bolt |
|
Nut |
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver as shown in the illustration.
Be careful not to damage the contact surfaces of the cylinder head, cylinder block and chain cover.
Tape the screwdriver tip before use.
Remove the oil pump gasket from the cylinder block.
Remove the O-ring from the oil pan.
16322
54.REMOVE WATER INLET PIPE
Remove the water inlet pipe.
Remove the 2 O-rings from the water inlet pipe.