Home › Engine / Hybrid System › 1VD-FTV (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052790 1VD-FTV INTAKE / EXHAUST _0255172 INTAKE MANIFOLD A

1VD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail, cylinder head, or intake manifold, it is necessary to replace the injection pipes with new ones.

·

w/ DPF:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).



PROCEDURE

Hide 17112 1.INSTALL NO. 2 INTAKE MANIFOLD

a.

Install a new gasket and the No. 2 intake manifold with the 9 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17111 2.INSTALL NO. 1 INTAKE MANIFOLD

a.

Install a new gasket and the No. 1 intake manifold with the 9 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23841C 3.INSTALL NO. 1 FUEL PIPE CLAMP (w/ DPF)

a.

Install the 2 No. 1 fuel pipe clamps with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23881D 4.INSTALL FUEL HOSE BRACKET (w/ DPF)

a.

Install the fuel hose bracket with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16268 5.INSTALL NO. 1 WATER BY-PASS PIPE

a.
U163522E02
2.719,1.219 2.844,1.365 0.125,0.146 10 false 1 1.073,0.865 1.198,1.01 0.125,0.146 10 false 2 0.094,0.021 0.385,0.24 0.292,0.219 10 true *A 0.094,2.354 0.448,2.604 0.354,0.25 10 true *B 2.792,3.344 2.917,3.49 0.125,0.146 10 false 1 0.917,3.844 1.042,3.99 0.125,0.146 10 false 2

Temporarily install a new gasket and the No. 1 water by-pass pipe with the union bolt and bolt.

Text in Illustration
*A w/ DPF
*B w/o DPF


b.

Tighten the union bolt and bolt in the order shown in the illustration.

Torque:
for union bolt : 59 N*m (600 kgf*cm, 43 ft.*lbf)
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23901H 6.INSTALL FUEL TUBE SUB-ASSEMBLY (w/ DPF)

a.

Attach the 3 clamps to install the fuel tube.


b.

Connect the 3 fuel tube connectors (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>PRECAUTION).


Hide 16283 8.CONNECT NO. 6 WATER BY-PASS HOSE (w/o DPF)

Hide 23764A 9.INSTALL NO. 4 NOZZLE LEAKAGE PIPE (w/o DPF)

a.
U162985E02
1.177,0.396 1.354,0.563 0.177,0.167 10 false 1 1.49,1.625 1.667,1.792 0.177,0.167 10 false 2

Temporarily install a new gasket and the No. 4 nozzle leakage pipe with the union bolt and bolt.


b.

Tighten the union bolt and bolt in the order shown in the illustration.

Torque:
for union bolt : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the No. 2 fuel hose to the fuel cooler.


Hide 23763 10.INSTALL NO. 3 NOZZLE LEAKAGE PIPE (w/o DPF)

a.
U162984E02
3.208,0.115 3.385,0.281 0.177,0.167 10 false 1 1.573,0.615 1.75,0.781 0.177,0.167 10 false 2

Temporarily install a new gasket and the No. 3 nozzle leakage pipe with the union bolt and bolt.


b.

Tighten the union bolt and bolt in the order shown in the illustration.

Torque:
for union bolt : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the No. 1 fuel hose to the fuel cooler.


Hide 25689 11.INSTALL EGR COOLER INSULATOR (w/ EGR System)

Hide 25620 12.INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)

a.

Connect the No. 5 water by-pass hose to the water by-pass outlet.


b.
U163523E02
0.729,1.052 0.854,1.198 0.125,0.146 10 false A 0.917,0.25 1.042,0.396 0.125,0.146 10 false B 0.729,1.458 0.854,1.604 0.125,0.146 10 false A 0.74,2.104 0.865,2.25 0.125,0.146 10 false A 2.49,1.021 2.615,1.167 0.125,0.146 10 false A 2.49,1.521 2.615,1.667 0.125,0.146 10 false A 2.5,2.156 2.625,2.302 0.125,0.146 10 false A 1.198,0.646 1.323,0.792 0.125,0.146 10 false B 2.26,0.26 2.385,0.406 0.125,0.146 10 false B 1.917,0.625 2.042,0.771 0.125,0.146 10 false B

Install 2 new gaskets and the EGR valve with EGR cooler with the 6 bolts labeled A and 4 bolts labeled B shown in the illustration.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt B : 29 N*m (296 kgf*cm, 21 ft.*lbf)

HINT:

The gasket claws should face toward the No. 1 and No. 2 EGR pipes.



Hide 25615A 13.INSTALL EGR PIPE INSULATOR (w/ EGR System)

a.

Install the EGR pipe insulator with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

If the No. 1 and No. 2 EGR pipe insulator installation stay is deformed, or the bolt holes of the EGR pipe insulator do not align, replace the No. 1 and No. 2 EGR pipes as a set.



Hide 17853B 14.INSTALL INTAKE MANIFOLD INSULATOR (w/ EGR System)

Hide 17114D 15.INSTALL NO. 3 INTAKE MANIFOLD

U162996E02
0.719,2.708 0.875,2.875 0.156,0.167 10 false A 0.719,3.094 0.875,3.26 0.156,0.167 10 false B

a.

Install 2 new gaskets to the No. 1 and No. 2 intake manifolds.


b.

Install the No. 3 intake manifold with the 16 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Bolt Length
Item Length
Bolt A 25 mm (0.984 in.)
Bolt B 70 mm (2.76 in.)


Hide 16.CONNECT NO. 2 ENGINE WIRE

a.
U162983E02
1.938,0.646 2.094,0.813 0.156,0.167 10 false A 3.01,1.167 3.167,1.333 0.156,0.167 10 false B 1.115,1.615 1.271,1.792 0.156,0.177 10 false A

Connect the No. 2 engine wire with the 3 bolts.

Torque:
for bolt A : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for bolt B : 32 N*m (326 kgf*cm, 24 ft.*lbf)


b.

Attach the 2 wire harness clamps.


Hide 17113 17.INSTALL INTAKE PIPE

a.

w/ EGR System:

Install 2 new gaskets and the intake pipe with the 6 bolts and 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

w/o EGR System:

Install a new gasket and the intake pipe with the 4 bolts and 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17136 18.INSTALL NO. 2 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

Hide 17135A 19.INSTALL NO. 1 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

Hide 23761A 20.INSTALL NO. 1 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23762B 21.INSTALL NO. 2 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23763 22.INSTALL NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)

a.

Temporarily install 2 new gaskets and the No. 3 nozzle leakage pipe with the 2 injector hollow screws and 3 bolts.


b.

Tighten the 2 injector hollow screws and 3 bolts.

Torque:
for injector hollow screw : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt : 21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

Tighten the injector hollow screws first, and then tighten the bolts.



Hide 27148B 23.INSTALL CONNECTING WIRE (w/ DPF)

a.

Attach the 2 clamps to install the connecting wire.


Hide 23810A 24.INSTALL COMMON RAIL ASSEMBLY RH

Hide 23702 25.INSTALL INJECTION PIPE RH

a.

Using a union nut wrench, install 4 new injection pipes.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)

NOTICE:
·

Make sure there is no damage or foreign matter on the seal surfaces.

·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




b.

w/ Intercooler:

Install the 4 injection pipe clamps with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 23711 26.INSTALL NO. 1 FUEL INJECTOR PROTECTOR (w/ DPF)

Hide 23712 27.INSTALL NO. 2 FUEL INJECTOR PROTECTOR (w/ DPF)

Hide 11224 28.INSTALL CYLINDER HEAD COVER SILENCER RH (w/ DPF)

Hide 23705 29.INSTALL NO. 5 INJECTION PIPE SUB-ASSEMBLY

a.

Temporarily install a new No. 5 injection pipe by hand.

NOTICE:

Make sure there is no damage or foreign matter on the seal surfaces.



b.
A267345

w/ DPF:

Temporarily install the used gasket and fuel filter to injection pump fuel pipe with the nut, bolt and union bolt.


c.
A185242

w/o DPF:

Temporarily install the used gasket and No. 2 fuel pipe with the nut, bolt and union bolt.


d.
A267346E03
0.094,0.083 0.281,0.24 0.188,0.156 10 false *A 0.094,2.469 0.417,2.708 0.323,0.24 10 true *B

Install the No. 2 injection pipe clamp with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

Text in Illustration
*A w/ DPF
*B w/o DPF


e.

Using a union nut wrench, tighten the No. 5 injection pipe ends.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



f.

Remove the bolt and No. 2 injection pipe clamp.


g.

Remove the union bolt and gasket.


h.

w/ DPF:

Remove the bolt, nut and fuel filter to injection pump fuel pipe.


i.

w/o DPF:

Remove the bolt, nut and No. 2 fuel pipe.


Hide 23243C 30.CONNECT FUEL PUMP MOTOR WIRE

a.

Install the fuel pump motor wire bracket to the No. 3 intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the connector to the fuel supply pump.


Hide 23801L 31.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

a.

w/ DPF:

NOTICE:

Check for damage and foreign matter on the fuel pipe installation surface of the fuel supply pump.

If there is foreign matter, remove it from the installation surface.

If the installation surface is damaged, replace the fuel supply pump.


i.

Temporarily install a new gasket and fuel filter to injection pump fuel pipe with the nut, bolt and union bolt.


ii.

Install the No. 2 injection pipe clamp with the bolt.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


iii.

Tighten the union bolt, bolt and nut.

Torque:
for union bolt : 12 N*m (125 kgf*cm, 9 ft.*lbf)
for bolt and nut : 10 N*m (102 kgf*cm, 7 ft.*lbf)


iv.

Connect the fuel hose.



b.

w/o DPF:

i.

Install the fuel filter to injection pump fuel pipe with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Connect the 2 hoses to the fuel pipe.



Hide 23820A 32.INSTALL COMMON RAIL ASSEMBLY LH

Hide 23765 33.INSTALL NO. 5 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23812D 34.INSTALL NO. 2 FUEL PIPE (w/ DPF)

Hide 23701 35.INSTALL INJECTION PIPE LH

a.

Using a union nut wrench, install the 4 new injection pipes.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)

NOTICE:
·

Make sure there is no damage or foreign matter on the seal surfaces.

·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




b.

w/ Intercooler:

Install the 4 injection pipe clamps with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 23764A 36.INSTALL NO. 4 NOZZLE LEAKAGE PIPE (w/ DPF)

a.

Temporarily install a new gasket and No. 4 nozzle leakage pipe with the fuel check valve.


b.

Tighten the fuel check valve.

Torque:
32 N*m (321 kgf*cm, 23 ft.*lbf)


c.

Connect the fuel hose.


Hide 11225 37.INSTALL CYLINDER HEAD COVER SILENCER LH (w/ DPF)

Hide 25706 38.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ DPF)

Hide 25860 39.INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/ DPF)

Hide 23706 40.CONNECT NO. 6 INJECTION PIPE SUB-ASSEMBLY

a.

w/ EGR System:

i.

Temporarily install a new No. 6 injection pipe to the common rail LH and RH.

NOTICE:

Make sure there is no damage or foreign matter on the seal surfaces.



ii.

Install the 2 No. 2 injection pipe clamps with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


iii.

Using a union nut wrench, tighten the No. 6 injection pipe ends.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




b.

w/o EGR System:

i.

Temporarily install a new No. 6 injection pipe to the common rail LH and RH.

NOTICE:

Make sure there is no damage or foreign matter on the seal surfaces.



ii.

Install the bracket to the No. 3 intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Install the No. 2 injection pipe clamp with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


iv.

Using a union nut wrench, tighten the No. 6 injection pipe ends.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 23802E 41.INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY (w/o DPF)

NOTICE:

Check for damage and foreign matter on the fuel pipe installation surface of the supply pump.

If there is foreign matter, remove it from the installation surface. If the installation surface is damaged, replace the fuel supply pump.


a.
U162976E02
0.573,0.24 0.729,0.406 0.156,0.167 10 false 1 1.281,1.188 1.438,1.354 0.156,0.167 10 false 2 2.823,0.813 2.979,0.979 0.156,0.167 10 false 3

Temporarily install a new gasket and the No. 2 fuel pipe with the union bolt, nut and bolt.


b.

Tighten the union bolt, nut and bolt in the order shown in the illustration.

Torque:
for union bolt : 25 N*m (255 kgf*cm, 18 ft.*lbf)
for bolt and nut : 10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Install the No. 2 injection pipe clamp with the bolt.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

Connect the fuel hose to the No. 5 nozzle leakage pipe.


Hide 42.CONNECT ENGINE WIRE

a.

LH Side:

i.

Install the engine wire protector with the 2 bolts.


ii.

Connect the 8 connectors.


iii.

Attach the wire harness clamp.


iv.

Install the engine wire harness bracket with the bolt.


v.

for RHD:

Connect the wire harness with the wire harness clamp holder.


vi.

Attach the 3 wire harness clamps and connect the 2 connectors.


vii.

Attach the 3 wire harness clamps and connect the 4 connectors.



b.

RH Side:

i.

Install the engine wire harness protector with the 3 bolts.


ii.

Connect the 7 connectors.


iii.

Attach the wire harness clamp.


iv.

Install the wire harness bracket with the bolt.


v.

Install the glow plug wire harness with the nut and screw grommet.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


vi.

for RHD:

Install the wire harness clamp holder with the bolt.


vii.

for RHD:

Connect the wire harness with the wire harness clamp holder.



c.

Rear Side:

i.

Install the glow plug wire harness with the nut and screw grommet.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


ii.

w/ DPF:

Connect the 3 connectors.


iii.

w/o DPF:

Connect the connector.


iv.

Install the engine wire harness protector with the 2 bolts.


v.

Install the 2 ground wires with the 2 bolts.

Torque:
8.4 N*m (87 kgf*cm, 74 in.*lbf)


vi.

Attach the wire harness clamp.



Hide 16288 43.INSTALL NO. 4 WATER BY-PASS PIPE

a.

w/ EGR System:

i.

w/ DPF:

Connect the 3 water hose ends, and temporarily install the No. 4 water by-pass pipe with the 2 bolts and nut.


ii.

w/o DPF:

Connect the 4 water hose ends, and temporarily install the No. 4 water by-pass pipe with the 2 bolts and nut.



b.

w/o EGR System:

Connect the 3 water hose ends, and temporarily install the No. 4 water by-pass pipe with the 2 bolts and nut.


c.

First tighten the 2 bolts and then tighten the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16268M 44.INSTALL NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

a.

Connect the 2 water hose ends, and install the No. 3 water by-pass pipe with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23274D 45.CONNECT FUEL HOSE

Hide 17885 46.INSTALL NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

a.

Connect the No. 1 air cleaner pipe to the No. 1 intake air connector pipe.


b.

Install the pipe with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Tighten the hose clamp.

Torque:
6.3 N*m (64 kgf*cm, 56 in.*lbf)


Hide 87208 47.INSTALL HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

a.

Connect the 4 water hose ends, and install the water pipe with the 4 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 17806 48.INSTALL NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

a.

Connect the No. 2 air cleaner pipe to the No. 2 intake air connector pipe.


b.

Connect the ventilation hose to the oil separator.


c.

Install the pipe with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Tighten the hose clamp.

Torque:
6.3 N*m (64 kgf*cm, 56 in.*lbf)


Hide 17364 49.INSTALL NO. 4 AIR TUBE

a.
A174723E04
2.594,2.667 1.99,2.667 true 2.292,2.156 2.542,2.302 0.25,0.146 10 false 90° 1.813,2.583 2,2.74 0.188,0.156 10 false *1 2.677,1.99 2.865,2.146 0.188,0.156 10 false *a

Install the No. 4 air tube with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Text in Illustration
*1 Paint Mark
*a Top


b.

Tighten the hose clamp.

Torque:
6.3 N*m (64 kgf*cm, 56 in.*lbf)

HINT:

Make sure the direction of the hose clamp is as shown in the illustration.



c.

Install the suction hose with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 17342D 50.INSTALL NO. 2 AIR HOSE

a.
U163093E03
2.302,2.531 1.99,2.292 1.99,2.292 1.885,2.292 true 0.542,2.76 0.854,3.198 0.854,3.198 0.958,3.198 true 2.365,2.635 1.948,3.208 1.948,3.208 1.833,3.208 true 0.167,2.25 0.406,2.406 0.24,0.156 10 false 90° 1.698,2.208 1.885,2.365 0.188,0.156 10 false *1 0.979,3.104 1.167,3.26 0.188,0.156 10 false *2 0.427,1.979 0.615,2.135 0.188,0.156 10 false *a 1.646,3.115 1.833,3.271 0.188,0.156 10 false *2 2.385,2.01 2.51,2.156 0.125,0.146 10 false A 2.344,3.167 2.469,3.313 0.125,0.146 10 false B

Connect the No. 2 air hose with the hose clamp.

Torque:
6.3 N*m (64 kgf*cm, 56 in.*lbf)

Text in Illustration
*1 Protrusion
*2 Paint Mark
*a Top

HINT:
·

Align the paint mark of the air hose with the protrusion and push on the air hose so that distance B is 0 to 3 mm (0 to 0.118 in.).

·

Position the clamp so that distance A is 2 to 6 mm (0.0787 to 0.236 in.).

·

Make sure the direction of the hose clamp is as shown in the illustration.




Hide 17363K 51.INSTALL NO. 3 AIR TUBE

a.
A174722E04
1.677,2.833 1.177,2.833 true 1.604,3.208 1.844,3.354 0.24,0.146 10 false 90° 0.979,2.75 1.167,2.906 0.188,0.156 10 false *1 1.74,2.177 1.927,2.333 0.188,0.156 10 false *a

Install the No. 3 air tube with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Text in Illustration
*1 Paint Mark
*a Top


b.

Tighten the hose clamp.

Torque:
6.3 N*m (64 kgf*cm, 56 in.*lbf)

HINT:

Make sure the direction of the hose clamp is as shown in the illustration.



c.

Install the wire harness bracket with the bolt.


d.

Install the ground wire with the nut, and attach the wire harness clamp.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


Hide 17341F 52.INSTALL NO. 1 AIR HOSE

a.
U163092E02
2.938,2.208 2.813,2.208 2.813,2.208 2.51,2.531 true 0.917,3.26 0.781,3.26 0.781,3.26 0.583,2.896 true 1.813,2.771 1.938,2.771 1.938,2.771 2.24,2.542 false 0.219,2.427 0.469,2.583 0.25,0.156 10 false 90° 2.333,2.063 2.458,2.208 0.125,0.146 10 false A 2.375,3.156 2.5,3.302 0.125,0.146 10 false B 2.979,2.135 3.167,2.292 0.188,0.156 10 false *1 0.938,3.167 1.125,3.323 0.188,0.156 10 false *2 0.615,2.229 0.802,2.385 0.188,0.156 10 false *a 1.604,2.688 1.792,2.844 0.188,0.156 10 false *2

Connect the No. 1 air hose with the hose clamp.

Torque:
6.3 N*m (64 kgf*cm, 56 in.*lbf)

Text in Illustration
*1 Protrusion
*2 Paint Mark
*a Top

HINT:
·

Align the paint mark of the air hose with the protrusion and push on the air hose so that distance B is 0 to 3 mm (0 to 0.118 in.).

·

Position the clamp so that distance A is 2 to 6 mm (0.0787 to 0.236 in.).

·

Make sure the direction of the hose clamp is as shown in the illustration.




Hide 17861 53.INSTALL INTAKE AIR CONNECTOR

a.

Connect the intake air connector to the No. 1 and No. 2 air cleaner pipes.


b.

Install the connector with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Tighten the 2 hose clamps.

Torque:
6.3 N*m (64 kgf*cm, 56 in.*lbf)


d.

Attach the 3 wire harness clamps.


e.

w/o Viscous Heater:

Connect the connector to the water temperature sensor.


f.

w/ Viscous Heater:

Connect the 2 connectors to the water temperature sensor and viscous with magnet clutch heater.


Hide 17881 54.TEMPORARILY INSTALL NO. 1 AIR CLEANER HOSE

a.

Temporarily install the air cleaner hose to the intake air connector.


Hide 17705 55.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

a.

Connect the air cleaner cap to the air cleaner hose, and install the air cleaner cap with the 4 clamps.


b.

Connect the mass air flow meter connector and attach the wire harness clamp to the air cleaner cap.


c.

Attach the wire harness clamp.


d.

Align the protrusion of the air cleaner cap and the concave portion of the air cleaner hose.


e.
A456630N01
1.906,0.635 2.365,0.833 0.458,0.198 10 false (A)

Tighten the 2 hose clamps.

(A):

15 mm or less



Hide 17947B 57.INSTALL NO. 3 INTERCOOLER SUPPORT BRACKET

Hide 31489 59.INSTALL TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)

Hide 31418 61.INSTALL CLUTCH HOSE (for Manual Transmission)

Hide 64.INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the No. 2 engine oil level dipstick guide.


c.

Install the No. 2 engine oil level dipstick guide with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the ventilation hose to the cylinder head cover RH.


e.

Connect the wire harness clamp to the No. 2 engine oil level dipstick guide bracket.


Hide 87209 65.CONNECT WATER HOSE SUB-ASSEMBLY

Hide 17973 66.INSTALL NO. 2 COOL AIR INLET (w/o Intercooler)

a.
A257096E02
1.233,2.211 1.368,2.211 1.368,2.211 1.552,2.705 false 1.025,2.122 1.210,2.277 0.185,0.155 10 *1 1.905,2.225 2.090,2.380 0.185,0.155 10 *a 1.029,2.687 1.214,2.842 0.185,0.155 10 *b

Install a new gasket to the air tube LH.

Text in Illustration
*1 Protrusion
*a Front
*b LH Side

HINT:

Install the gasket with the protrusion facing as shown in the illustration.



b.

Install the No. 2 cool air inlet with the 3 nuts and bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.
U163424E02
2.135,2.198 2.25,2.198 2.25,2.198 2.49,2.5 true 1.135,3.094 1.021,3.094 1.021,3.094 0.771,2.75 true 2.188,2.792 2.302,2.792 2.302,2.792 2.594,2.521 false 2.917,2.135 3.042,2.281 0.125,0.146 10 false A 2.875,2.958 3,3.104 0.125,0.146 10 false B 0.396,2.281 0.656,2.427 0.26,0.146 10 false 90° 1.948,2.125 2.135,2.281 0.188,0.156 10 false *1 0.792,2.115 0.979,2.271 0.188,0.156 10 false *a 1.146,3 1.333,3.156 0.188,0.156 10 false *2 2,2.698 2.188,2.854 0.188,0.156 10 false *2

Connect the No. 2 air hose to the No. 2 cool air inlet.

Text in Illustration
*1 Protrusion
*2 Paint Mark
*a Top


d.

Tighten the No. 2 air hose clamp.

Torque:
6.3 N*m (64 kgf*cm, 56 in.*lbf)

HINT:
·

Align the paint mark of the air hose with the protrusion and push on the air hose so that distance B is 0 to 3 mm (0 to 0.118 in.).

·

Position the clamp so that distance A is 2 to 6 mm (0.0787 to 0.236 in.).

·

Make sure the direction of the hose clamp is as shown in the illustration.




Hide 17973 67.INSTALL NO. 1 COOL AIR INLET (w/o Intercooler)

a.
A257095E03
2.146,2.146 2.01,2.146 2.01,2.146 1.823,2.552 false 2.167,2.073 2.354,2.229 0.188,0.156 10 false *1 1.49,2.188 1.677,2.344 0.188,0.156 10 false *a 2.344,2.719 2.531,2.875 0.188,0.156 10 false *b

Install a new gasket to the air tube RH.

Text in Illustration
*1 Protrusion
*a Front
*b RH Side

HINT:

Install the gasket with the protrusion facing as shown in the illustration.



b.

Install the No. 1 cool air inlet with the 3 nuts and bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Connect the vacuum hose, intake air temperature sensor connector and turbo pressure sensor connector.


d.
U163423E02
2.844,2.188 2.729,2.188 2.729,2.188 2.427,2.51 true 1.125,3.094 1.021,3.094 1.021,3.094 0.771,2.76 true 1.844,2.708 1.958,2.708 1.958,2.708 2.156,2.5 false 1.906,2.125 2.031,2.271 0.125,0.146 10 false A 1.917,2.958 2.042,3.104 0.125,0.146 10 false B 0.406,2.271 0.667,2.417 0.26,0.146 10 false 90° 2.875,2.125 3.063,2.281 0.188,0.156 10 false *1 1.135,2.99 1.323,3.146 0.188,0.156 10 false *2 0.792,2.104 0.979,2.26 0.188,0.156 10 false *a 1.646,2.625 1.833,2.781 0.188,0.156 10 false *2

Connect the No. 1 air hose to the No. 1 cool air inlet.

Text in Illustration
*1 Protrusion
*2 Paint Mark
*a Top


e.

Tighten the No. 1 air hose clamp.

Torque:
6.3 N*m (64 kgf*cm, 56 in.*lbf)

HINT:
·

Align the paint mark of the air hose with the protrusion and push on the air hose so that distance B is 0 to 3 mm (0 to 0.118 in.).

·

Position the clamp so that distance A is 2 to 6 mm (0.0787 to 0.236 in.).

·

Make sure the direction of the hose clamp is as shown in the illustration.




Hide 17940D 68.INSTALL INTERCOOLER ASSEMBLY (w/ Intercooler)

Hide 70.CHECK FOR CLUTCH FLUID LEAK

Hide 71.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

Connect the cables to the negative (-) main battery and sub-battery terminals.


Hide 75.INSPECT FOR OIL LEAK

Hide 53292A 76.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 51405A 77.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53805 78.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 53806 79.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH