16100
1.INSTALL WATER PUMP ASSEMBLY
Temporarily install a new gasket and the water pump with the 9 bolts and 2 nuts.
| Item | Length |
|---|---|
| Bolt A | 30 mm (1.18 in.) |
| Bolt B | 80 mm (3.15 in.) |
Uniformly tighten the 9 bolts and 2 nuts of the water pump in the order shown in the illustration.
After installing all of the bolts and nuts, check that all of the bolts and nuts are tightened to the torque specification.
16331
2.INSTALL WATER OUTLET
Connect the water outlet to the No. 2 water hose joint, and install a new gasket and the water outlet with the 2 bolts.
16307A
3.INSTALL FAN BRACKET SUB-ASSEMBLY
Install the fan bracket with the 4 bolts.
| Item | Length |
|---|---|
| Bolt A | 30 mm (1.18 in.) |
| Bolt B | 80 mm (3.15 in.) |
15777
4.INSTALL NO. 1 OIL COOLER HOSE
Make sure that there is clearance between the oil cooler hose and crankshaft pulley.
5.INSTALL NO. 2 IDLER PULLEY BRACKET (w/ Viscous Heater)
Temporarily install the No. 2 idler pulley bracket with the bolt.
Temporarily install the 2 bolts to the No. 2 idler pulley bracket bolt hole.
Uniformly tighten the 3 bolts of the No. 2 idler pulley bracket in the order shown in the illustration.
16630H
6.INSTALL NO. 2 IDLER PULLEY (w/ Viscous Heater)
Install the collar, No. 2 idler pulley and cover with the bolt.
16331A
7.INSTALL THERMOSTAT
16321
8.INSTALL WATER INLET
9.INSTALL NO. 1 IDLER PULLEY BRACKET (w/ Viscous Heater)
87120G
10.INSTALL VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (w/ Viscous Heater)
87208
11.INSTALL HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)
16371
12.INSTALL FAN PULLEY
16711
13.INSTALL FAN SHROUD WITH FAN
32942
14.INSTALL OIL COOLER TUBE (for Automatic Transmission)
16361A
15.INSTALL V-RIBBED BELT
16.INSTALL NO. 3 IDLER PULLEY (w/ Viscous Heater)
17.INSTALL NO. 1 IDLER PULLEY (w/ Viscous Heater)
18.INSTALL V-RIBBED BELT (w/ Viscous Heater)
16572D
19.CONNECT NO. 2 RADIATOR HOSE
16571C
20.CONNECT NO. 1 RADIATOR HOSE
44310
21.INSTALL VANE PUMP ASSEMBLY
16470
22.INSTALL RADIATOR RESERVOIR ASSEMBLY
44369A
23.INSTALL NO. 1 OIL RESERVOIR BRACKET
44360
24.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY
17861
25.INSTALL INTAKE AIR CONNECTOR
17881
26.TEMPORARILY INSTALL NO. 1 AIR CLEANER HOSE
17705
27.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
12601E
28.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)
82113
29.INSTALL NO. 3 ENGINE ROOM WIRE
28800
30.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Connect the cables to negative (-) main battery and sub-battery terminals.
31.ADD ENGINE COOLANT
32.INSPECT FOR ENGINE COOLANT LEAK
53292A
33.INSTALL UPPER RADIATOR SUPPORT SEAL
51405A
34.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
53805
35.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
53806
36.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53736G
37.INSTALL FRONT FENDER APRON SEAL FRONT RH
38.INSTALL FRONT WHEEL RH