Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL COOLER › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255261 OIL COOLER A

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  OIL COOLER  INSTALLATION  


PROCEDURE

Hide 32910 1.INSTALL OIL COOLER ASSEMBLY

U164650E01
2.423,2.547 2.640,2.705 0.217,0.158 10 *b 0.193,1.123 0.410,1.324 0.217,0.201 10 *a 0.195,2.922 0.412,3.124 0.217,0.201 10 *a

a.

Connect the oil cooler inlet hose and outlet hose.

Text in Illustration
*a Lower Side
*b Outward


b.

Install the rear transmission oil cooler air duct with the 4 bolts, and then install the air cooled oil cooler tube to the transmission oil cooler air duct with the bolt.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


c.
C344204E02
2.479,0.104 2.313,0.104 2.313,0.104 1.771,0.344 false 2.542,0.031 2.75,0.208 0.208,0.177 10 false *a 2.24,1.135 2.396,1.323 0.156,0.188 10 true 1 1.115,1.115 1.229,1.281 0.115,0.167 10 false 3 1.854,3.104 1.969,3.271 0.115,0.167 10 true 4 1.323,3.115 1.438,3.281 0.115,0.167 10 true 2

Temporarily put the oil cooler on the radiator support.

NOTICE:

Securely attach the 2 claws of the oil cooler into the holes of the radiator support.


Text in Illustration
*a Claw


d.

Install the 4 bolts in the sequence shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 32917 2.INSTALL TRANSMISSION OIL COOLER AIR DUCT

a.

Install the oil cooler air duct with the 4 bolts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 32907A 3.INSTALL OIL COOLER TUBE

U165076E01
0.114,0.053 0.360,0.293 0.246,0.239 12 *A 3.801,0.053 4.040,0.293 0.239,0.239 12 *B 2.317,1.017 2.437,1.177 0.120,0.160 10 A 1.662,1.364 1.780,1.527 0.118,0.163 10 B 5.99,1.07 6.132,1.230 0.141,0.160 10 A 5.006,1.364 5.134,1.527 0.128,0.163 10 B

Text in Illustration
*A for 1VD-FTV *B for 1UR-FE

a.

Temporarily install the oil cooler tube to the fan shroud with bolt A. Install bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 32941H 4.CONNECT INLET NO. 4 OIL COOLER HOSE

C175576E02
2.257,0.443 2.58,0.825 false 2.516,0.311 2.58,0.825 2.58,0.825 1.681,0.825 false 1.472,0.735 1.677,0.914 0.205,0.179 10 *1

a.

Connect the inlet oil cooler hose as shown in the illustration.

NOTICE:

Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.


Text in Illustration
*1 Paint Mark


Hide 32942 5.CONNECT INLET NO. 2 OIL COOLER HOSE AND INLET NO. 3 OIL COOLER HOSE

C226980E01
0.127,0.1 0.362,0.314 0.235,0.214 12 *A 4.443,0.1 4.696,0.314 0.253,0.214 12 *B

Text in Illustration
*A for 1VD-FTV *B for 1UR-FE

a.

Connect the 2 inlet oil cooler hoses as shown in the illustration.

NOTICE:

Make sure the pinching portion of each clip is facing the direction shown in the illustration.



Hide 32942 6.CONNECT INLET NO. 1 OIL COOLER HOSE AND OUTLET NO. 1 OIL COOLER HOSE

U165077E02
6.771,0.552 6.354,0.104 6.354,0.104 6.188,0.104 false 6.427,0.51 6.354,0.115 false 5.125,0.646 5.542,0.677 false 3.271,0.458 2.844,0.094 2.844,0.094 2.677,0.094 false 2.917,0.417 2.844,0.094 false 1.385,0.573 1.948,0.563 false 2.99,1.323 2.646,1.583 false 6.688,1.948 6.271,1.771 false 4.188,0.031 4.417,0.25 0.229,0.219 12 false *B 0.052,0.031 0.313,0.25 0.26,0.219 12 false *A 2.948,2 3.156,2.177 0.208,0.177 10 true *1 2.51,0.031 2.698,0.208 0.188,0.177 10 true *1 1.969,0.479 2.188,0.656 0.219,0.177 10 true *1 5.51,0.604 5.729,0.781 0.219,0.177 10 true *1 5.99,0.042 6.177,0.219 0.188,0.177 10 false *1 6.458,1.354 6.698,1.563 0.24,0.208 10 true *1

Text in Illustration
*A for 1VD-FTV *B for 1UR-FE
*1 Paint Mark - -

a.

Connect the 2 oil cooler hoses as shown in the illustration.

NOTICE:

Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.



b.

Attach the hose to the flexible hose clamp and close the clamp as shown in the illustration.


Hide 32943B 7.CONNECT TRANSMISSION OIL COOLER HOSE

U164617E01
0.846,2.835 1.028,2.999 0.182,0.165 10 *a 0.17,2.326 0.418,2.500 0.248,0.174 10 45° 0.17,2.631 0.418,2.805 0.248,0.174 10 45° 1.378,2.486 1.573,2.651 0.195,0.165 10 *b 0.713,2.121 1.241,2.565 1.241,2.565 1.322,2.565 false

a.

Connect the 2 transmission oil cooler hoses as shown in the illustration.

Text in Illustration
*a RH Side
*b Paint Mark

NOTICE:
·

Make sure the pinching portion of each clip is facing the direction shown in the illustration.

·

Make sure the paint mark of each hose is facing outward.




Hide 8.ADD AUTOMATIC TRANSMISSION FLUID

Hide 52521 9.INSTALL FRONT UPPER CENTER BUMPER RETAINER

Hide 51405A 11.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53806 12.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 13.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 53782 15.INSTALL FRONT FENDER APRON SEAL FRONT RH