Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY(for 3UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255272 AUTOMATIC TRANSMISSION ASSEMBLY(for 3UR-FE) A

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 3UR-FE)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53806 3.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51440 7.REMOVE OIL PAN PROTECTOR ASSEMBLY

C171483

a.

Remove the 4 bolts and oil pan protector assembly.


Hide 33702B 12.DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

C170828

a.

Remove the clip and pin and disconnect the gear shifting rod from the transmission control shaft lever RH.


Hide 37140 13.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110 14.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 11452 18.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 17167 19.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17104 20.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 32101A 23.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.
C161354

Turn the crankshaft to gain access to the 6 bolts and remove the bolts while holding the crankshaft pulley setting bolt with a wrench.


Hide 32943 24.DISCONNECT TRANSMISSION OIL COOLER HOSE

C181045

a.

Disconnect the 2 transmission oil cooler hoses from the oil cooler tube union.


Hide 35000 25.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

C161356

a.

Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.

NOTICE:

Support the oil pan bolts to prevent damage to the oil pan gasket.



Hide 51203 26.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

C171484

a.

Remove the engine mounting hole cover.


b.
C171489

Remove the 4 bolts of the rear engine mounting insulator.


c.
U164644

Remove the 4 nuts, 4 bolts and No. 3 frame crossmember.


Hide 12371 27.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

C172399

a.

Remove the 2 bolts and engine mounting heat insulator.


b.

Remove the 4 bolts and rear engine No. 1 mounting insulator from the transmission.


Hide 28.DISCONNECT WIRE HARNESS AND CONNECTOR

C171503

a.

Remove the bolt and disconnect the ground cable.


b.
U152359

Tilt the transmission downward.

NOTICE:
·

Support the oil pan bolts to prevent damage to the oil pan gasket.


·

Make sure the cooling fan does not contact the fan shroud.




c.
C228999

Remove the 4 wire harness clamps.


d.

Disconnect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed sensor connectors and 3 transfer control connectors.

C228368

HINT:

Detach the claw, press down the lever, and then disconnect the transmission wire connector.



e.

Detach the 4 connector clamps and 11 harness clamps.


Hide 35000 29.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

C175536

a.

Remove the 10 bolts and transmission.

NOTICE:

Do not use excess force to pry off the transmission assembly.



Hide 36407 30.DISCONNECT TRANSFER BREATHER HOSE SUB-ASSEMBLY

a.
C175541

Disconnect the 2 breather plug hoses from the harness clamp bracket.


b.
C228919

Detach the 3 breather hose clamps from the automatic transmission breather tube.


Hide 36179 31.REMOVE LOWER TRANSFER CASE PROTECTOR

a.
C171493

Detach the clamp of the ground cable from the lower transfer case protector.


b.

Remove the 7 bolts and lower transfer case protector.


Hide 33.REMOVE HARNESS CLAMP BRACKET

a.

Remove the 8 bolts and 8 harness clamp brackets.

C228367


Hide 32000 34.REMOVE TORQUE CONVERTER ASSEMBLY