Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052849 INTERIOR PANELS / TRIM _0255717 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 55400 1.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for LHD)

a.

Install the instrument panel safety pad with the 8 bolts and 2 nuts.


b.

Install the 2 passenger airbag bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

B180534


c.

Connect the wire harness with the bolt.


d.

Connect the connectors and attach the clamps.

B180532


e.

Connect the connectors.

B182523E01
1.076,1.537 2.400,1.952 1.324,0.416 12 w/ Parking Assist Monitor System: 3.204,1.537 6.404,1.948 3.200,0.411 12 w/ TOYOTA Parking Assist-Sensor System and w/o Parking Assist Monitor System:


Hide 55400 2.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for RHD)

a.

Install the instrument panel safety pad with the 8 bolts and 2 nuts.


b.

Connect the connectors.


c.

Install the 2 passenger airbag bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

B180535


d.

Connect the wire harness with the bolt.


e.

Connect the connectors and attach the clamps.

B180533


f.

Connect the connectors.

B187975E01
1.362,1.549 2.685,1.965 1.324,0.416 12 w/ Parking Assist Monitor System: 3.247,1.549 6.447,1.960 3.200,0.411 12 w/ TOYOTA Parking Assist-Sensor System and w/o Parking Assist Monitor System:


Hide 87212H 3.INSTALL REAR NO. 4 AIR DUCT (w/ Rear Air Duct)

B180309

a.

Attach the clip to install the rear No. 4 air duct.


Hide 87212F 4.INSTALL REAR NO. 2 AIR DUCT (w/ Rear Air Duct)

B180308

a.

Attach the clip to install the rear No. 2 air duct.


Hide 6.INSTALL MULTI-MEDIA MODULE RECEIVER ASSEMBLY WITH BRACKET (w/ Multi-display)

Hide 55522B 7.INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)

B180654

a.

Install the radio tuner opening cover with the 2 bolts and 2 screws.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 86120 8.INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Cassette Tape Player)

Hide 55412C 9.INSTALL NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL

B180653

a.

Connect the connector.


b.

Attach the 10 claws to install the No. 1 center instrument cluster finish panel.


Hide 86120 10.INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Multi-display)

Hide 86111 11.INSTALL MULTI-DISPLAY ASSEMBLY WITH BRACKET (w/ Multi-display)

Hide 55680A 12.INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

B182866

a.

Connect the connector.


b.

Attach the 6 claws to install the No. 4 instrument panel register.


Hide 55670 13.INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

B182547

a.

Connect the connector.


b.

Attach the 6 claws to install the No. 3 instrument panel register.


Hide 86160P 14.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (RH Side)

Hide 55409F 15.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

Hide 86160P 16.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (LH Side)

Hide 55408F 17.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

Hide 55510F 19.INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY

Hide 62211 20.INSTALL FRONT PILLAR GARNISH RH (w/ Sliding Roof)

Hide 62211 21.INSTALL FRONT PILLAR GARNISH RH (w/o Sliding Roof)

Hide 62212 22.INSTALL FRONT PILLAR GARNISH LH (w/ Sliding Roof)

Hide 62212 23.INSTALL FRONT PILLAR GARNISH LH (w/o Sliding Roof)

Hide 74610A 24.INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Sliding Roof)

Hide 74610A 25.INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

Hide 55660 26.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

B180305

a.

Attach the 4 claws to install the No. 2 instrument panel register.


Hide 55433B 27.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

B180304

a.

Connect the connector.


b.

Attach the 3 claws to install the lower No. 2 instrument panel finish panel.


c.

Install the 4 bolts.


Hide 55443D 28.INSTALL INSTRUMENT PANEL BOX DOOR KNOB

B182549

a.

Attach the 2 claws to install the instrument panel box door knob.


Hide 55476A 29.INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH

B182550

a.

Attach the 6 claws to install the No. 3 instrument cluster finish panel garnish.


Hide 55312 30.INSTALL LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)

B180302

a.

Attach the 4 claws to install the lower instrument panel.


b.

Install the 2 bolts.


Hide 73990 31.INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

Hide 62111C 32.INSTALL COWL SIDE TRIM BOARD RH

B180022

a.

Attach the 2 clips to install the cowl side trim board.


b.

Install the cap nut.


Hide 55607 33.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B182552

a.

Attach the 4 claws to install the No. 2 instrument panel under cover.


Hide 67913B 34.INSTALL FRONT DOOR SCUFF PLATE RH (w/ Sliding Roof)

Hide 67913B 35.INSTALL FRONT DOOR SCUFF PLATE RH (w/o Sliding Roof)

Hide 55317A 36.INSTALL INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

B186358

a.

Connect the connector.


b.

Attach the 6 claws to install the instrument side panel.


Hide 55317A 37.INSTALL INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

B182551

a.

Attach the 6 claws to install the instrument side panel.


Hide 55650 38.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

B180300

a.

Attach the 4 claws to install the No. 1 instrument panel register.


Hide 55303B 39.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

B180299

a.

Attach the 2 claws and connect the DLC3.


b.

Install the lower instrument panel with the 5 bolts.


Hide 73900 40.INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55446A 41.INSTALL NO. 1 SWITCH HOLE BASE

B180298

a.

Connect the connectors.


b.

Attach the 4 claws to install the No. 1 switch hole base.


Hide 55432D 42.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

a.

Connect the connectors.


b.
B180296

for Automatic Air Conditioning System:

i.

Attach the 2 claws to install the room temperature sensor.



c.
B181942

Attach the 2 claws to connect the 2 control cables.


d.

w/ Driver Side Knee Airbag:

i.

Attach the 16 claws to install the lower No. 1 instrument panel finish panel.


ii.

Install the 2 bolts.

B291249



e.

w/o Driver Side Knee Airbag:

i.

Attach the 9 claws to install the lower No. 1 instrument panel finish panel.


ii.

Install the 2 bolts.

B291250



f.
B182569

Attach the 2 claws to close the hole cover.


Hide 62112 43.INSTALL COWL SIDE TRIM BOARD LH

B181911

a.

Attach the 2 clips to install the cowl side trim board.


b.

Install the cap nut.


Hide 55606 44.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B182553

a.

Connect the connectors.


b.

Attach the 3 claws to install the No. 1 instrument panel under cover.


c.

Install the 2 screws.


Hide 67914B 45.INSTALL FRONT DOOR SCUFF PLATE LH (w/ Sliding Roof)

Hide 67914B 46.INSTALL FRONT DOOR SCUFF PLATE LH (w/o Sliding Roof)

Hide 83100 47.INSTALL COMBINATION METER ASSEMBLY (w/o Multi-information Display)

B180018

a.

Connect the connectors.


b.

Install the combination meter with the 4 screws.


Hide 83100 48.INSTALL COMBINATION METER ASSEMBLY (w/ Multi-information Display)

B180019

a.

Connect the connectors.


b.

Install the combination meter with the 4 screws.


Hide 55404C 49.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Multi-information Display)

B180016

a.

Attach the 9 claws to install the instrument cluster finish panel.


Hide 55404C 50.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Multi-information Display)

B180017

a.

Connect the connector.


b.

Attach the 9 claws to install the instrument cluster finish panel.


Hide 55475A 51.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.

Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.

B291252E01
3.871,0.224 4.165,0.540 0.295,0.316 10 *B 0.396,0.224 0.691,0.540 0.295,0.316 10 *A

Text in Illustration
*A w/ Entry and Start System *B w/o Entry and Start System


Hide 55474C 52.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

E155133

a.

Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.


Hide 55318C 53.INSTALL INSTRUMENT SIDE PANEL LH

E155518

a.

Attach the 6 claws to install the instrument side panel.


Hide 58812A 54.INSTALL LOWER CONSOLE BOX (w/o Console Box Lid)

Hide 88520 55.INSTALL COOLING BOX ASSEMBLY (w/ Cool Box)

Hide 58901A 56.INSTALL REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)

Hide 57.INSTALL FRONT SEAT ASSEMBLY RH (for Bench Seat Type)

Hide 71100S 58.INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)

Hide 71100S 59.INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)

Hide 71200S 60.INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)

Hide 71200S 61.INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)

Hide 84140 62.INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)

Hide 84140 63.INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)

Hide 89235A 64.INSTALL TILT AND TELESCOPIC SWITCH (for Power Tilt and Power Telescopic Steering Column)

Hide 45286B 65.INSTALL UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

Hide 45286B 66.INSTALL UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

Hide 67.INSTALL LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

Hide 68.INSTALL LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

Hide 45100 69.INSTALL STEERING WHEEL ASSEMBLY

Hide 45186 71.INSTALL LOWER NO. 2 STEERING WHEEL COVER

Hide 45187 72.INSTALL LOWER NO. 3 STEERING WHEEL COVER

Hide 73.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
·

for Power Tilt and Power Telescopic Steering Column:

Reset the Autoaway/Return function setting to the previous condition by changing the customize parameter (See page General>INTRODUCTION>REPAIR INSTRUCTION>CUSTOMIZE PARAMETERS).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 76.CHECK FOR REFRIGERANT GAS LEAK (w/ Cool Box)