Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052824 POWER ASSIST SYSTEMS _0255437 POWER STEERING SYSTEM G

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT DRIVE BELT

a.
C125842E03
0.615,3.784 0.844,3.934 0.229,0.150 10 *a 1.594,3.784 1.823,3.934 0.229,0.150 10 *b 2.548,3.784 2.777,3.934 0.229,0.150 10 *c

Visually check the belt for excessive wear, frayed cords, etc.

Text in Illustration
*a Correct
*b Incorrect
*c Incorrect

If any defect is found, replace the drive belt.

HINT:

Cracks on the rib side of a belt are considered acceptable. Replace the belt if there are any missing ribs.



b.

Check by hand that the belt fits properly in the ribbed grooves and has not slipped out of the grooves on the bottom of the crank pulley.


Hide 2.BLEED POWER STEERING SYSTEM

a.

Check the fluid level.


b.

Jack up the front of the vehicle and support it with stands.


c.

Turn the steering wheel.

i.

With the engine stopped, turn the wheel slowly from lock to lock several times.



d.

Lower the vehicle.


e.

Start the engine.


f.

Idle the engine for a few minutes.


g.

Turn the steering wheel.

i.

With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds. *1


ii.

Repeat *1 several times.

NOTICE:

For vehicles with VGRS, if the steering wheel is turned from lock to lock repeatedly, the system may stop operating and the amount of rotation before the steering wheel locks may increase due to operation of the overheating prevention function. When the system temperature drops, the system operation automatically returns to normal.




h.

Stop the engine.


i.
C124274E03
0.574,0.312 1.303,0.462 0.730,0.150 10 *a 1.919,0.312 2.841,0.462 0.922,0.150 10 *b

Check for foaming or emulsification.

Text in Illustration
*a Correct
*b Incorrect

If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.


j.

Check the fluid level.


Hide 3.CHECK FLUID LEVEL

a.
C158723E02
0.478,0.875 0.653,1.056 0.174,0.180 10 *a 2.794,0.751 2.968,0.917 0.174,0.166 10 *b

Keep the vehicle horizontal.

Text in Illustration
*a COLD Range
*b HOT Range


b.

With the engine stopped, check the fluid level in the reservoir.

If necessary, add fluid.

Fluid:

ATF DEXRON II or III, or equivalent


HINT:

If the fluid is hot, check that the fluid level is within the HOT range. If the fluid is cold, check that the fluid level is within the COLD range.



c.

Start the engine and idle it.


d.

Turn the steering wheel from lock to lock several times to raise the fluid temperature.

Fluid temperature:

80°C (176°F)



e.
C124274E03
0.574,0.312 1.303,0.462 0.730,0.150 10 *a 1.919,0.312 2.841,0.462 0.922,0.150 10 *b

Check for foaming or emulsification.

Text in Illustration
*a Correct
*b Incorrect

If foaming or emulsification is identified, bleed the power steering system.


f.
U153404E01
0.858,1.589 1.046,1.739 0.187,0.150 10 *a 1.632,1.368 1.825,1.530 0.192,0.162 10 *c 2.356,1.589 2.533,1.739 0.177,0.150 10 *b 1.437,0.986 1.835,0.986 false 1.591,0.909 2.006,0.909 false 1.718,0.808 1.718,0.545 false 1.726,1.092 1.726,1.355 false

With the engine idling, measure the fluid level in the reservoir.

Text in Illustration
*a Engine idling
*b Engine stopped
*c 5.0 mm (0.197 in.) or less


g.

Stop the engine.


h.

Wait a few minutes and remeasure the fluid level in the reservoir.

Maximum fluid level rise:

5.0 mm (0.197 in.)


If the fluid level rise is more than the maximum, bleed the power steering system.


i.

Check the fluid level.


Hide 4.CHECK STEERING FLUID PRESSURE

a.

Disconnect the pressure feed tube from the vane pump.

i.

for 1GR-FE:

Refer to the following procedures (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 1GR-FE)>REMOVAL).


ii.

for 1UR-FE:

Refer to the following procedures (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 1UR-FE)>REMOVAL).


iii.

for 1VD-FTV (without DPF):

Refer to the following procedures (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 1VD-FTV without DPF)>REMOVAL).


iv.

for 3UR-FE:

Refer to the following procedures (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 3UR-FE)>REMOVAL).



b.

Connect SST as shown in the illustration.

SST
09640-10010  (09641-01010, 09641-01030, 09641-01060)

U165232E02
1.948,1.448 2.594,2.052 true 2.594,2.052 2.74,2.052 false 3.219,0.75 3.177,0.594 false 3.177,0.594 3.052,0.594 false 3.281,3.438 3.24,3.281 false 3.24,3.281 3.125,3.281 false 0.906,3.875 1.042,3.875 1.042,3.875 1.26,4.292 false 1.75,3.365 1.865,3.188 1.865,3.188 1.979,3.188 true 1.094,1.5 0.979,2.333 true 1.74,2.115 1.698,2.333 1.698,2.333 0.865,2.333 true 6.49,2.208 6.448,2.052 false 6.448,2.052 6.333,2.052 false 1.083,4.979 1.01,5.323 1.01,5.323 0.885,5.323 true 5.417,3.323 5.333,4.188 5.333,4.188 5.167,4.188 true 6.073,4.094 6.156,3.99 6.156,3.99 6.25,3.99 false 0.688,2.271 0.917,2.417 0.229,0.146 10 false *1 2.781,1.979 3.031,2.177 0.25,0.198 10 false *2 2.75,0.521 3.115,0.708 0.365,0.188 10 false SST 2.917,1.104 3.135,1.271 0.219,0.167 10 false *a 3.458,1.104 3.688,1.26 0.229,0.156 10 false *b 2.031,3.125 2.271,3.271 0.24,0.146 10 false *1 0.719,5.25 0.927,5.396 0.208,0.146 10 false *1 0.74,3.813 1,4.01 0.26,0.198 10 false *2 3,3.896 3.219,4.063 0.219,0.167 10 false *a 3.563,3.906 3.906,4.063 0.344,0.156 10 false *b 2.823,3.219 3.188,3.406 0.365,0.188 10 false SST 0.438,3.177 0.823,3.375 0.385,0.198 12 false *B 6.031,1.99 6.396,2.177 0.365,0.188 10 false SST 6.167,2.573 6.385,2.74 0.219,0.167 10 false *a 6.74,2.563 7.083,2.719 0.344,0.156 10 false *b 4.094,2.792 4.302,2.99 0.208,0.198 10 false *1 3.844,1.885 4.177,2.104 0.333,0.219 12 false *C 5,4.104 5.208,4.323 0.208,0.219 10 false *2 6.281,3.927 6.479,4.104 0.198,0.177 10 false *1 0.438,0.563 0.656,0.76 0.219,0.198 12 false *A

Text in Illustration
*A for 1GR-FE *B for 1VD-FTV without DPF
*C for 1UR-FE, 3UR-FE - -
*1 Attachment *2 Pressure feed tube
*a IN *b OUT

NOTICE:

Make sure that the valve of SST is in the open position.



c.

Bleed the power steering system.


d.

Start the engine and idle it.


e.

Turn the steering wheel from lock to lock several times to raise the fluid temperature.

Fluid temperature:

80°C (176°F)



f.
C358277E01
0.365,0.906 0.583,1.104 0.219,0.198 10 false *1 2.677,0.354 2.896,0.552 0.219,0.198 10 false *2 2.688,1.396 2.906,1.594 0.219,0.198 10 false *3 1.229,0.927 1.448,1.125 0.219,0.198 10 false *a 1.469,1.615 1.781,1.813 0.313,0.198 10 false SST

With the engine idling, close the valve of SST and observe the reading on SST.

Standard fluid pressure:

10000 to 10700 kPa (102.0 to 109.0 kgf/cm2, 1450 to 1551 psi)


Text in Illustration
*1 Power steering gear
*2 Oil reservoir
*3 Vane pump
*a Closed

NOTICE:
·

Do not keep the valve closed for more than 10 seconds.

·

Do not allow the fluid temperature to become too high.



If the pressure is less than the minimum, check for fluid leaks and replace parts as necessary.


g.
C358278E01
0.354,0.917 0.552,1.115 0.198,0.198 10 false *1 2.667,0.313 2.865,0.51 0.198,0.198 10 false *2 2.708,1.354 2.906,1.552 0.198,0.198 10 false *3 1.313,0.927 1.51,1.125 0.198,0.198 10 false *a 1.438,1.635 1.813,1.823 0.375,0.188 10 false SST

With the engine idling, fully open the valve.

Text in Illustration
*1 Power steering gear
*2 Oil reservoir
*3 Vane pump
*a Open


h.

Measure the fluid pressure at engine speeds of 1000 rpm and 3000 rpm.

Difference in fluid pressure:

500 kPa (5.1 kgf/cm2, 73 psi) or less


NOTICE:

Do not turn the steering wheel.


If the pressure difference is higher than the specified value, check for fluid leaks and replace parts as necessary.


i.
C358279E01
0.365,0.854 0.594,1.042 0.229,0.188 10 false *1 2.646,0.26 2.875,0.448 0.229,0.188 10 false *2 2.656,1.323 2.885,1.51 0.229,0.188 10 false *3 1.188,0.875 1.417,1.063 0.229,0.188 10 false *a 1.156,0.427 1.385,0.615 0.229,0.188 10 false *b 1.333,1.573 1.646,1.771 0.313,0.198 10 false SST

With the engine idling and the valve fully open, turn the steering wheel left or right to the full lock position. Observe the reading on SST.

Standard fluid pressure:

10000 to 10700 kPa (102.0 to 109.0 kgf/cm2, 1450 to 1551 psi)


Text in Illustration
*1 Power steering gear
*2 Oil reservoir
*3 Vane pump
*a Open
*b Lock position

NOTICE:
·

Do not keep the steering wheel in the full lock position for more than 10 seconds.

·

Do not allow the fluid temperature to become too high.



If the pressure is less than the minimum, check for fluid leaks and replace parts as necessary.


j.

Disconnect SST.

SST
09640-10010  (09641-01010, 09641-01030, 09641-01060)


k.

Connect the pressure feed tube to the vane pump.

i.

for 1GR-FE:

Refer to the following procedures (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 1GR-FE)>INSTALLATION).


ii.

for 1UR-FE:

Refer to the following procedures (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 1UR-FE)>INSTALLATION).


iii.

for 1VD-FTV (without DPF):

Refer to the following procedures (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 1VD-FTV without DPF)>INSTALLATION).


iv.

for 3UR-FE:

Refer to the following procedures (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 3UR-FE)>INSTALLATION).



l.

Bleed the power steering system.