Home › Steering › VARIABLE GEAR RATIO STEERING › VARIABLE GEAR RATIO STEERING SYSTEM › from 2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255448 VARIABLE GEAR RATIO STEERING SYSTEM C

VARIABLE GEAR RATIO STEERING  VARIABLE GEAR RATIO STEERING SYSTEM  C15A5/65  Lock Mechanism Circuit  


DESCRIPTION

If the VGRS ECU (steering control ECU) detects a malfunction in the lock mechanism, it turns the master warning light on, and stores DTC C15A5/65.

DTC No. DTC Detection Condition Trouble Area
C15A5/65 Both conditions are met for approximately 0.025 seconds or more:
·

The engine switch is on (IG).

·

A short in the motor circuit or an internal malfunction in the ECU is detected.


·

Steering actuator assembly

·

VGRS ECU (steering control ECU)

·

Harness or connector



CAUTION / NOTICE / HINT

NOTICE:

When replacing the VGRS ECU (steering control ECU) or steering actuator assembly, perform actuator angle neutral point calibration and initialization after replacing parts (See page Steering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (LV, LG TERMINAL)
a.
U165229E02
1.99,1.073 1.563,1.583 1.563,1.583 1.563,1.74 false 2.031,1.146 2.417,1.563 2.417,1.563 2.417,1.729 false 0.063,0 0.25,0.188 0.188,0.188 10 false *a 1.552,0.229 1.906,0.406 0.354,0.177 10 false E162 1.333,1.771 1.75,1.969 0.417,0.198 10 false 2 (LV) 2.188,1.771 2.625,1.958 0.438,0.188 10 false 6 (LG)

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

HINT:

With the connector connected to the VGRS ECU (steering control ECU), measure the voltage from the rear of the connector.


Standard Voltage:
Tester Connection Condition Specified Condition
E162-2 (LV) - Body ground Engine switch on (IG) 11 to 14 V
E162-6 (LG) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(VGRS ECU [Steering Control ECU])



OK

2.READ VALUE USING GTS (LOCK SOLENOID VOLTAGE)

NG

3.INSPECT STEERING ACTUATOR ASSEMBLY
2.READ VALUE USING GTS (LOCK SOLENOID VOLTAGE)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / VGRS / Data List.

VGRS
Tester Display Measurement Item /Range Normal Condition Diagnostic Note
Lock Solenoid Voltage Lock solenoid voltage/
Min.: 0.00 V
Max.: 255.99 V
0 to 14 V -

OK:

0 to 14 V (while the engine is being started)


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

REPLACE VGRS ECU (STEERING CONTROL ECU)

C

REPLACE VGRS ECU (STEERING CONTROL ECU)

3.INSPECT STEERING ACTUATOR ASSEMBLY
a.

Turn the engine switch off.


b.
U165258E02
1.448,1.333 1.021,1.521 1.021,1.521 1.021,1.729 false 1.635,1.115 2.333,0.781 2.333,0.781 2.615,0.781 false 0.125,0.083 0.396,0.365 0.271,0.281 10 false *a 0.917,1.76 1.177,1.938 0.26,0.177 10 false LG 1.542,0.302 1.906,0.458 0.365,0.156 10 false E162 2.656,0.708 2.917,0.885 0.26,0.177 10 false LV

Disconnect the E162 VGRS ECU (steering control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

HINT:
·

Measure the resistance of the steering actuator assembly at the connector of the VGRS ECU (steering control ECU).



Standard Resistance:
Tester Connection Condition Specified Condition
E162-2 (LV) - E162-6 (LG) Always 10 to 30 Ω
E162-2 (LV) - Body ground Always 100 kΩ or higher
E162-6 (LG) - Body ground Always 100 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to VGRS ECU [Steering Control ECU])

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE VGRS ECU (STEERING CONTROL ECU)

B

REPLACE VGRS ECU (STEERING CONTROL ECU)

C

4.CHECK HARNESS AND CONNECTOR (VGRS ECU (STEERING CONTROL ECU) - STEERING ACTUATOR ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (VGRS ECU (STEERING CONTROL ECU) - STEERING ACTUATOR ASSEMBLY)
a.

Turn the engine switch off.


b.

Disconnect the E162 VGRS ECU (steering control ECU) connector.


c.

Disconnect the E80 steering actuator assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E162-2 (LV) - E80-7 (LV+) Always Below 1 Ω
E162-6 (LG) - E80-16 (LG+) Always Below 1 Ω
E162-2 (LV) - E80-6 (LG) Always 10 to 30 Ω
E162-2 (LV) or E80-7 (LV+) - Body ground Always 100 kΩ or higher
E162-6 (LG) or E80-16 (LG+) - Body ground Always 100 kΩ or higher




OK

REPLACE STEERING ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR