| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B15C3 | A short is detected in the speaker output circuit. | ·
Stereo component amplifier assembly ·
Speaker ·
Harness or connector |
After the inspection is completed, clear the DTCs.
NEXT
Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).
DTC B15C3 is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
*1: for RH Side
*2: for LH Side
*3: for 14 Speakers
*4: for 9 Speakers
Disconnect the F74 stereo component amplifier assembly connector.
Disconnect the I1*1 and/or I10*2 front No. 1 speaker assembly connector.
Disconnect the F7*1 and/or F8*2 front No. 2 speaker assembly connector.
Disconnect the F6 front No. 4 speaker assembly connector.
Disconnect the J15*1 and/or J17*2 rear speaker set connector*4.
Disconnect the J2*1 and/or J9*2 rear No. 3 speaker connector*3.
Disconnect the S8*1 and/or S9*2 rear header speaker assembly connector*3.
Disconnect the L4 No. 1 woofer box speaker connector.*3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F74-5 (WFR+) - I1-1*1 | Always | Below 1 Ω |
| F74-20 (WFR-) - I1-2*1 | Always | Below 1 Ω |
| F74-4 (WFL+) - I10-1*2 | Always | Below 1 Ω |
| F74-19 (WFL-) - I10-2*2 | Always | Below 1 Ω |
| F74-13 (FR+) - F7-1 (+)*1 | Always | Below 1 Ω |
| F74-28 (FR-) - F7-3 (-)*1 | Always | Below 1 Ω |
| F74-12 (FL+) - F8-1 (+)*2 | Always | Below 1 Ω |
| F74-27 (FL-) - F8-2 (-)*2 | Always | Below 1 Ω |
| F74-7 (CTR+) - F6-1 | Always | Below 1 Ω |
| F74-22 (CTR-) - F6-2 | Always | Below 1 Ω |
| F74-15 (RR+) - J15-1*1, *4 | Always | Below 1 Ω |
| F74-30 (RR-) - J15-2*1, *4 | Always | Below 1 Ω |
| F74-14 (RL+) - J17-1*2, *4 | Always | Below 1 Ω |
| F74-29 (RL-) - J17-2*2, *4 | Always | Below 1 Ω |
| F74-15 (R-R+) - J2-1 (+)*1, *3 | Always | Below 1 Ω |
| F74-30 (R-R) - J2-3 (-)*1, *3 | Always | Below 1 Ω |
| F74-14 (R-L+) - J9-1 (+)*2, *3 | Always | Below 1 Ω |
| F74-29 (R-L-) - J9-3 (-)*2, *3 | Always | Below 1 Ω |
| F74-11 (SR+) - S8-1 (RRD+)*1, *3 | Always | Below 1 Ω |
| F74-26 (SR-) - S8-2 (RRD-)*1, *3 | Always | Below 1 Ω |
| F74-10 (SL+) - S9-1 (RLD+)*2, *3 | Always | Below 1 Ω |
| F74-25 (SL-) - S9-2 (RLD-)*2, *3 | Always | Below 1 Ω |
| F74-6 (WF1+) - L4-1 (WF1+)*3 | Always | Below 1 Ω |
| F74-21 (WF1-) - L4-2 (WF1-)*3 | Always | Below 1 Ω |
| F74-8 (WF2+) - L4-3 (WF2+)*3 | Always | Below 1 Ω |
| F74-23 (WF2-) - L4-4 (WF2-)*3 | Always | Below 1 Ω |
| F74-5 (WFR+) - Body ground | Always | 10 kΩ or higher |
| F74-20 (WFR-) - Body ground | Always | 10 kΩ or higher |
| F74-4 (WFL+) - Body ground | Always | 10 kΩ or higher |
| F74-19 (WFL-) - Body ground | Always | 10 kΩ or higher |
| F74-13 (FR+) - Body ground | Always | 10 kΩ or higher |
| F74-28 (FR-) - Body ground | Always | 10 kΩ or higher |
| F74-12 (FL+) - Body ground | Always | 10 kΩ or higher |
| F74-27 (FL-) - Body ground | Always | 10 kΩ or higher |
| F74-7 (CTR+) - Body ground | Always | 10 kΩ or higher |
| F74-22 (CTR-) - Body ground | Always | 10 kΩ or higher |
| F74-15 (RR+) - Body ground | Always | 10 kΩ or higher |
| F74-30 (RR-) - Body ground | Always | 10 kΩ or higher |
| F74-14 (RL+) - Body ground | Always | 10 kΩ or higher |
| F74-29 (RL-) - Body ground | Always | 10 kΩ or higher |
| F74-15 (R-R+) - Body ground | Always | 10 kΩ or higher |
| F74-30 (R-R) - Body ground | Always | 10 kΩ or higher |
| F74-14 (R-L+) - Body ground | Always | 10 kΩ or higher |
| F74-29 (R-L-) - Body ground | Always | 10 kΩ or higher |
| F74-11 (SR+) - Body ground | Always | 10 kΩ or higher |
| F74-26 (SR-) - Body ground | Always | 10 kΩ or higher |
| F74-10 (SL+)- Body ground | Always | 10 kΩ or higher |
| F74-25 (SL-) - Body ground | Always | 10 kΩ or higher |
| F74-6 (WF1+) - Body ground | Always | 10 kΩ or higher |
| F74-21 (WF1-) - Body ground | Always | 10 kΩ or higher |
| F74-8 (WF2+) - Body ground | Always | 10 kΩ or higher |
| F74-23 (WF2-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the front No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 1.8 to 2.6 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3 Ω |
| Result | Proceed to |
|---|---|
| OK (for 14 Speakers) | A |
| OK (for 9 Speakers) | B |
| NG | C |
A
B
C
Disconnect the front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (+) - 2 (TWR+) | Always | Below 1 Ω |
| 3 (-) - 4 (TWR-) | Always | Below 1 Ω |
| 2 (TWR+) - 4 (TWR-) | Always | 1.5 to 2.5 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (+) - 2 (TWL+) | Always | Below 1 Ω |
| 3 (-) - 4 (TWL-) | Always | Below 1 Ω |
| 2 (TWL+) - 4 (TWL-) | Always | 1.5 to 2.5 Ω |
| *A | for RH Side |
| *B | for LH Side |
OK
NG
Temporarily replace the front No. 3 speaker assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL).
Check for DTCs and check if the same DTCs is output (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).
No DTCs are output.
OK
NG
Temporarily replace the front No. 2 speaker assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL).
Check for DTCs and check if the same DTCs is output (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).
No DTCs are output.
A
B
Disconnect the front No. 3 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (-) - 2 (+) | Always | 4 Ω |
OK
NG
*1: for RH Side
*2: for LH Side
Disconnect the F7*1 and/or F8*2 front No. 2 speaker assembly connector.
Disconnect the F13*1 and/or F14*2 front No. 3 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F7-2 (TWR+) - F13-1 | Always | Below 1 Ω |
| F7-4 (TWR-) - F13-2 | Always | Below 1 Ω |
| F7-2 (TWR+) - Body ground | Always | 10 kΩ or higher |
| F7-4 (TWR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F8-2 (TWL+) - F14-1 | Always | Below 1 Ω |
| F8-4 (TWL-) - F14-2 | Always | Below 1 Ω |
| F8-2 (TWL+) - Body ground | Always | 10 kΩ or higher |
| F8-4 (TWL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the front No. 4 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 1.5 to 2.5 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 6 Ω |
OK
NG
Disconnect the rear speaker set connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (WF+) - 2 (WF-) | Always | 1.5 to 2.3 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (WF+) - 2 (WF-) | Always | 4 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (WF+) - 2 (WF-) | Always | 5 Ω |
| Result | Proceed to |
|---|---|
| OK (for 14 Speakers) | A |
| OK (for 9 Speakers) | B |
| NG | C |
A
B
C
*1: for RH Side
*2: for LH Side
Disconnect the J2*1 and/or J9*2 front No. 3 speaker assembly connector.
Disconnect the J18*1 and/or J19*2 rear speaker set connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J2-2 (+) - J18-1 (WF+) | Always | Below 1 Ω |
| J2-4 (-) - J18-2 (WF-) | Always | Below 1 Ω |
| J2-2 (+) - Body ground | Always | 10 kΩ or higher |
| J2-4 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J9-2 (+) - J19-1 (WF+) | Always | Below 1 Ω |
| J9-4 (-) - J19-2 (WF-) | Always | Below 1 Ω |
| J9-2 (+) - Body ground | Always | 10 kΩ or higher |
| J9-4 (-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the rear header assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (RRD+) - 2 (RRD-) | Always | 1.5 to 2.5 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (RLD+) - 2 (RLD-) | Always | 1.5 to 2.5 Ω |
| *A | for RH Side |
| *B | for LH Side |
OK
NG
Temporarily replace the rear No. 3 speaker assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).
Check for DTCs and check if the same DTCs is output (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).
No DTCs are output.
OK
NG
Disconnect the No. 1 woofer box speaker assembly speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (WF1+) - 2 (WF1-) | Always | 1.6 to 2.4 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (WF2+) - 4 (WF2-) | Always | 1.6 to 2.4 Ω |
OK
NG