Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15C0  Short in GPS Antenna  B15C1  Open in GPS Antenna  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly (w/o Roof Antenna) or telephone antenna assembly (w/ Roof Antenna).

DTC Code DTC Detection Condition Trouble Area
B15C0 Navigation antenna error
·

w/o Roof Antenna

-

Navigation antenna assembly

-

Multi-media module receiver assembly


·

w/ Roof Antenna, w/o DAB Function

-

Telephone antenna assembly

-

No. 3 antenna cord sub-assembly

-

No. 2 antenna cord sub-assembly

-

Antenna cord sub-assembly

-

Multi-media module receiver assembly


·

w/ Roof Antenna, w/ DAB Function

-

Telephone antenna assembly

-

Digital audio broadcasting antenna assembly

-

No. 2 antenna cord sub-assembly

-

Antenna cord sub-assembly

-

Multi-media module receiver assembly



B15C1 Error of the power source to the navigation antenna

WIRING DIAGRAM

E281002E02
3.24,0.75 3.594,0.99 0.354,0.24 10 false 1a 3.219,0.313 3.563,0.552 0.344,0.24 10 false 1 5.615,0.76 5.969,1 0.354,0.24 10 false 1a 5.677,0.292 6.021,0.531 0.344,0.24 10 false 1 5.708,1.479 6.969,1.833 1.26,0.354 10 false Multi-media Module Receiver Assembly 5.688,1.271 6.083,1.469 0.396,0.198 10 false GA 5.865,0.406 6.302,0.615 0.438,0.208 10 false GPS 5.615,5.198 5.969,5.438 0.354,0.24 10 false 1a 5.688,4.771 6.031,5.01 0.344,0.24 10 false 1 4.906,5.198 5.375,5.438 0.469,0.24 10 false E-4a 4.906,4.781 5.375,5.021 0.469,0.24 10 false E-4 5.823,5.906 7.083,6.26 1.26,0.354 10 false Multi-media Module Receiver Assembly 5.823,5.729 6.219,5.927 0.396,0.198 10 false GA 4.792,5.906 5.781,6.271 0.99,0.365 10 false Antenna Cord Sub-assembly 1.75,5.854 2.969,6.417 1.219,0.563 10 false Digital Audio Broadcasting Antenna Assembly 3.219,5.906 4.49,6.271 1.271,0.365 10 false No. 2 Antenna Cord Sub-assembly 0.344,5.708 1.615,6.073 1.271,0.365 10 false Telephone Antenna Assembly 0.146,4.219 3.604,4.469 3.458,0.25 12 false w/ Roof Antenna, w/ DAB Function: 3.958,5.208 4.427,5.448 0.469,0.24 10 false D-4a 4.021,4.781 4.49,5.021 0.469,0.24 10 false D-4 3.302,5.208 3.771,5.448 0.469,0.24 10 false C-1a 3.302,4.792 3.771,5.031 0.469,0.24 10 false C-1 2.365,5.198 2.833,5.438 0.469,0.24 10 false B-1a 2.406,4.781 2.875,5.021 0.469,0.24 10 false B-1 1.698,5.219 2.167,5.458 0.469,0.24 10 false A-2a 1.708,4.792 2.177,5.031 0.469,0.24 10 false A-2 5.885,4.854 6.323,5.063 0.438,0.208 10 false GPS 5.615,2.771 5.969,3.01 0.354,0.24 10 false 1a 5.677,2.344 6.021,2.583 0.344,0.24 10 false 1 4.906,2.771 5.375,3.01 0.469,0.24 10 false E-1a 4.906,2.333 5.375,2.573 0.469,0.24 10 false E-1 5.823,3.458 7.083,3.813 1.26,0.354 10 false Multi-media Module Receiver Assembly 5.813,3.271 6.208,3.469 0.396,0.198 10 false GA 4.792,3.427 5.781,3.792 0.99,0.365 10 false Antenna Cord Sub-assembly 1.729,3.469 3,3.833 1.271,0.365 10 false No. 3 Antenna Cord Sub-assembly 3.219,3.438 4.49,3.802 1.271,0.365 10 false No. 2 Antenna Cord Sub-assembly 2.073,1.24 4.115,1.469 2.042,0.229 10 false Navigation Antenna Assembly 0.354,3.365 1.625,3.729 1.271,0.365 10 false Telephone Antenna Assembly 0.135,0.094 1.729,0.344 1.594,0.25 12 false w/o Roof Antenna: 0.146,1.771 3.604,2.021 3.458,0.25 12 false w/ Roof Antenna, w/o DAB Function: 3.958,2.771 4.427,3.01 0.469,0.24 10 false D-1a 4.031,2.333 4.5,2.573 0.469,0.24 10 false D-1 3.302,2.771 3.771,3.01 0.469,0.24 10 false C-1a 3.302,2.344 3.771,2.583 0.469,0.24 10 false C-1 2.354,2.76 2.823,3 0.469,0.24 10 false B-1a 2.417,2.344 2.885,2.583 0.469,0.24 10 false B-1 1.698,2.781 2.167,3.021 0.469,0.24 10 false A-2a 1.698,2.375 2.167,2.615 0.469,0.24 10 false A-2 5.865,2.438 6.302,2.646 0.438,0.208 10 false GPS

PROCEDURE

1.CHECK VEHICLE TYPE
a.

Select the vehicle setting.

Result
Result Proceed to
w/o Roof Antenna A
w/ Roof Antenna, w/o DAB Function B
w/ Roof Antenna, w/ DAB Function C



A

2.CHECK CONNECTION OF NAVIGATION ANTENNA ASSEMBLY

B

6.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

C

12.CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY
2.CHECK CONNECTION OF NAVIGATION ANTENNA ASSEMBLY
a.

Check if the navigation antenna assembly is securely connected to the multi-media module receiver assembly.

OK:

Navigation antenna assembly is securely connected.




OK

3.REPLACE NAVIGATION ANTENNA ASSEMBLY

NG

SECURELY CONNECT NAVIGATION ANTENNA ASSEMBLY

3.REPLACE NAVIGATION ANTENNA ASSEMBLY
a.

Replace the navigation antenna assembly with a normally functioning one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA (for Instrument Panel Side)>REMOVAL).



NEXT

4.CLEAR DTC
5.CHECK DTC
a.

Recheck for DTCs and check if the same DTCs are output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (NAVIGATION ANTENNA ASSEMBLY IS DEFECTIVE)

NG

6.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
U166435E01
0.246,0.217 0.522,0.521 0.276,0.304 10 *a 1.631,2.593 1.842,2.776 0.211,0.184 10 B 1.631,0.53 1.842,0.714 0.211,0.184 10 A 2.503,3.088 2.780,3.392 0.276,0.304 10 1a 0.641,0.951 0.918,1.255 0.276,0.304 10 2a 2.446,3.185 2.315,3.185 2.315,3.185 1.988,3.543 false 0.865,1.054 0.997,1.054 0.997,1.054 1.323,1.412 false 0.257,2.28 0.534,2.584 0.276,0.304 10 *b

Disconnect the No. 3 antenna cord sub-assembly from telephone antenna assembly connector.


b.

Disconnect the No. 3 antenna cord sub-assembly from No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-1 Always Below 1 Ω
A-2a - B-1a Always Below 1 Ω
A-2 - Body ground Always 10 kΩ or higher
A-2a - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Telephone Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)



OK

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
U166433E01
0.231,0.179 0.571,0.438 0.340,0.259 10 *a 0.274,2.224 0.614,2.483 0.340,0.259 10 *b 2.382,3.181 2.722,3.440 0.340,0.259 10 1a 2.367,3.268 2.246,3.267 2.246,3.267 1.974,3.598 false 2.382,1.067 2.722,1.326 0.340,0.259 10 1a 2.367,1.154 2.246,1.153 2.246,1.153 1.922,1.484 false 1.688,2.585 1.902,2.799 0.214,0.214 10 D 1.663,0.502 1.877,0.716 0.214,0.214 10 C

Disconnect the No. 2 antenna cord sub-assembly from No. 3 antenna cord sub-assembly.


b.

Disconnect the No. 2 antenna cord sub-assembly from antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-1 - D-1 Always Below 1 Ω
C-1a - D-1a Always Below 1 Ω
C-1 - Body ground Always 10 kΩ or higher
C-1a - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)



OK

8.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

8.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
U166434E02
2.188,4.073 2.052,4.073 2.052,4.073 1.76,3.51 false 2.323,3.219 2.198,3.219 2.198,3.219 1.896,3.49 false 2.323,1.146 2.198,1.146 2.198,1.146 1.896,1.406 false 0.208,0.146 0.688,0.521 0.479,0.375 10 false *a 0.344,2.26 0.823,2.635 0.479,0.375 10 false *b 2.208,3.979 2.635,4.167 0.427,0.188 10 false GPS 2.354,3.135 2.646,3.323 0.292,0.188 10 false 1a 2.354,1.063 2.646,1.25 0.292,0.188 10 false 1a 1.646,0.469 1.813,0.635 0.167,0.167 10 false E 1.594,2.51 1.833,2.677 0.24,0.167 10 false GA

Disconnect the antenna cord sub-assembly from No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna cord sub-assembly from multi-media module receiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-1 - GA-1 (GPS) Always Below 1 Ω
E-1a - GA-1a Always Below 1 Ω
E-1 - Body ground Always 10 kΩ or higher
E-1a - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Multi-media Module Receiver Assembly)



OK

9.REPLACE TELEPHONE ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

9.REPLACE TELEPHONE ANTENNA ASSEMBLY
a.

Replace the telephone antenna assembly with a normally functioning one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA (for Roof Side)>REMOVAL).



NEXT

10.CLEAR DTC
11.CHECK DTC
a.

Recheck for DTCs and check if the same DTCs are output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (TELEPHONE ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

12.CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY
a.
U166451E01
0.441,0.776 0.763,1.015 0.323,0.239 10 2a 0.71,0.859 0.865,0.859 0.865,0.859 1.337,1.202 false 1.638,2.609 1.961,2.848 0.323,0.239 10 B 1.638,0.375 1.961,0.614 0.323,0.239 10 A 2.851,2.868 3.174,3.108 0.323,0.239 10 1a 2.311,3.693 2.718,2.967 2.718,2.967 2.834,2.967 false 0.269,2.254 0.591,2.493 0.323,0.239 10 *b 0.269,0.192 0.591,0.431 0.323,0.239 10 *a

Disconnect the digital audio broadcasting antenna assembly from telephone antenna assembly connector.


b.

Disconnect the digital audio broadcasting antenna assembly from No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-1 Always Below 1 Ω
A-2a - B-1a Always Below 1 Ω
A-2 - Body ground Always 10 kΩ or higher
A-2a - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Telephone Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)



OK

13.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY

13.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
U166452E01
0.32,0.982 0.643,1.221 0.323,0.239 10 1a 0.59,1.065 0.744,1.065 0.744,1.065 1.217,1.408 false 1.69,2.455 2.012,2.694 0.323,0.239 10 D 1.69,0.409 2.012,0.648 0.323,0.239 10 C 0.741,2.661 1.063,2.900 0.323,0.239 10 4a 1.498,3.475 1.076,2.763 1.076,2.763 0.96,2.763 false 0.252,2.268 0.575,2.507 0.323,0.239 10 *b 0.252,0.274 0.575,0.513 0.323,0.239 10 *a

Disconnect the No. 2 antenna cord sub-assembly from digital audio broadcasting antenna assembly.


b.

Disconnect the No. 2 antenna cord sub-assembly from antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-1 - D-4 Always Below 1 Ω
C-1a - D-4a Always Below 1 Ω
C-1 - Body ground Always 10 kΩ or higher
C-1a - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Digital Audio Broadcasting Antenna Assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)



OK

14.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

14.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
U166453E02
2.188,1.292 2.531,0.677 2.531,0.677 2.646,0.677 false 1.885,3.469 2.344,3.073 2.344,3.073 2.427,3.073 false 1.771,3.583 2.115,4.271 2.115,4.271 2.219,4.271 false 1.594,2.521 1.917,2.76 0.323,0.24 10 false GA 1.656,0.365 1.979,0.604 0.323,0.24 10 false E 2.729,0.583 3.052,0.823 0.323,0.24 10 false 4a 2.5,2.979 2.823,3.219 0.323,0.24 10 false 1a 2.271,4.198 2.625,4.438 0.354,0.24 10 false GPS 0.24,2.26 0.563,2.5 0.323,0.24 10 false *b 0.229,0.115 0.552,0.354 0.323,0.24 10 false *a

Disconnect the antenna cord sub-assembly from No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna cord sub-assembly from multi-media module receiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-4 - GA-1 (GPS) Always Below 1 Ω
E-4a - GA-1a Always Below 1 Ω
E-4 - Body ground Always 10 kΩ or higher
E-4a - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Multi-media Module Receiver Assembly)



OK

15.REPLACE TELEPHONE ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

15.REPLACE TELEPHONE ANTENNA ASSEMBLY
a.

Replace the telephone antenna assembly with a normally functioning one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA (for Roof Side)>REMOVAL).



NEXT

16.CLEAR DTC
17.CHECK DTC
a.

Recheck for DTCs and check if the same DTCs are output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

2.CHECK CONNECTION OF NAVIGATION ANTENNA ASSEMBLY

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY