The video signal from the each television camera is transmitted to the multi-display assembly*1 or radio and display receiver assembly*2.
*1: for Multi-media Module Receiver Type
*2: for Radio and Display Type
for LHD, Multi-media Module Receiver Type:
for RHD, Multi-media Module Receiver Type:
for Radio and Display Type:
When "!" mark is displayed on the multi-display after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION).
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Electrical devices are used in the cabin (noise may occur in the image).
The camera lens is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).
The camera lens is dirty with snow, mud, etc.
A strong beam of light, such as a sunbeam or headlight, hits the camera.
It is too dark around the camera (at night, etc.).
The ambient temperature around the camera is either too high or too low.
The vehicle is tilted at a steep angle.
The television camera assembly lens is scratched.
The television camera assembly lens has drops of water on it or the humidity is high.
When the camera is used under fluorescent lights, sodium lights, or mercury lights, etc., the lights and the illuminated area may appear to flicker.
Check if the same malfunction occurs when the multi-terrain monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Rear view screen is not displayed. | A |
| Front view screen is not displayed. | B |
| Passenger side monitor screen is not displayed. | C |
| Driver side monitor screen is not displayed. | D |
| Multi-terrain monitor screen is not displayed. | E |
A
B
C
D
E
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
for LHD:
Replace the side television camera assembly RH with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL).
for RHD:
Replace the side television camera assembly LH with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL).
Check if the same malfunction reoccurs when the multi-terrain monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Malfunction does not reoccur (returns to normal) | A |
| Malfunction reoccurs (for LHD) | B |
| Malfunction reoccurs (for RHD) | B |
A
B
C
OK
NG
OK
NG
OK
NG
for LHD:
Replace the side television camera assembly LH with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL).
for RHD:
Replace the side television camera assembly RH with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL).
Check if the same malfunction reoccurs when the multi-terrain monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Malfunction does not reoccur (returns to normal) | A |
| Malfunction reoccurs (for LHD) | B |
| Malfunction reoccurs (for RHD) | B |
A
B
C
According to the display on the GTS, read the Data List. (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Video Output Status | Status of the video output status / OK or NG | OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal |
- |
OK is displayed.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Multi-media Module Receiver Type) | B |
| NG (for Radio and Display Type) | C |
A
B
C
Replace the GVIF cable with a new or normally functioning one.
Check if the same malfunction reoccurs when the multi-terrain monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Malfunction does not reoccur (returns to normal) | A |
| Malfunction reoccurs | B |
A
B
Replace the multi-display assembly with a new or normally functioning one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY (w/ Navigation System)>REMOVAL).
Check if the same malfunction reoccurs when the multi-terrain monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Malfunction does not reoccur (returns to normal) | A |
| Malfunction reoccurs | B |
A
B
Disconnect the F75 parking assist ECU connector.
Disconnect the F118 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F75-11 (TX+) - F118-7 (TX1+) | Always | Below 1 Ω |
| F75-10 (TX-) - F118-8 (TX1-) | Always | Below 1 Ω |
| F75-11 (TX+) - Body ground | Always | 10 kΩ or higher |
| F75-10 (TX-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the radio and display receiver assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/o Multi-display)>REMOVAL).
Check if the same malfunction reoccurs when the multi-terrain monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Malfunction does not reoccur (returns to normal) | A |
| Malfunction reoccurs | B |
A
B