The main body ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN MS bus.
When the main body ECU receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.
If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| U1002 (CAN MS BUS) | Lost communication with the gateway module (main body ECU). | ·
MS bus circuit ·
Windshield wiper ECU CAN branch wire or connector*1 ·
Position control ECU and switch CAN branch wire or connector*2 ·
Outer mirror control ECU assembly CAN branch wire or connector*2 ·
Multiplex tilt and telescopic ECU branch wire or connector*3 ·
Certification ECU (smart key ECU assembly) CAN branch wire or connector*4 ·
Power back door unit assembly (power back door ECU) CAN branch wire or connector*5 ·
Tire pressure warning ECU and receiver CAN branch wire or connector*6 ·
No. 2 main body ECU CAN branch wire or connector*5 ·
Main body ECU (cowl side junction block LH) CAN main wire or connector ·
Combination meter assembly CAN main wire or connector ·
Accessory bus buffer CAN branch wire or connector ·
Windshield wiper ECU*1 ·
Position control ECU and switch*2 ·
Outer mirror control ECU assembly*2 ·
Multiplex tilt and telescopic ECU*3 ·
Certification ECU (smart key ECU assembly)*4 ·
Power back door unit assembly (power back door ECU)*5 ·
Tire pressure warning ECU and receiver*6 ·
No. 2 main body ECU*5 ·
Main body ECU (cowl side junction block LH) ·
Combination meter assembly ·
Accessory bus buffer ·
No. 8 junction connector ·
No. 9 junction connector ·
No. 10 junction connector ·
No. 2 CAN junction connector |
*1: w/ Rain Sensor
*2: w/ Seat Memory
*3: w/ Power Tilt Power Telescopic Steering Column System
*4: w/ Entry and Start System
*5: w/ Power Back Door System
*6: w/ Tire Pressure Warning System
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
NEXT
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
For vehicles with an SRS system:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
NEXT
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Resistance Malfunction |
|---|---|---|---|
| E3-16 (CANP) - E3-15 (CANN) | Ignition switch off | 54 to 69 Ω | Below 53 Ω: Short in line |
| E3-16 (CANP) - E3-15 (CANN) | Ignition switch off | 54 to 69 Ω | 70 Ω or higher: Open in CAN main bus line |
| E3-16 (CANP) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher | Below 6 kΩ: +B short |
| E3-15 (CANN) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher | Below 6 kΩ: +B short |
| E3-16 (CANP) - E22-4 (CG) | Ignition switch off | 200 Ω or higher | Below 200 Ω: Ground short |
| E3-15 (CANN) - E22-4 (CG) | Ignition switch off | 200 Ω or higher | Below 200 Ω: Ground short |
| *a | Component with harness connected
(Main Body ECU [Cowl Side Junction Block LH]) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| NG
·
Open in CAN main wire |
A |
| NG
·
Short in line ·
+B short ·
Ground short |
B |
| OK | C |
A
B
C
Disconnect the L29 No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L29-1 (CANH) - L29-2 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
OK
NG
Disconnect the L30 No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L30-1 (CANH) - L30-2 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
OK
NG
Reconnect the L29 No. 2 CAN junction connector.
NEXT
Disconnect the E76 No. 8 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E76-6 (CANH) - E76-17 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 8 Junction Connector) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E76-1 (CANH) - E76-12 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 8 Junction Connector) |
OK
NG
Reconnect the E76 No. 8 junction connector.
NEXT
Disconnect the E3 main body ECU (cowl side junction block LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E3-16 (CANP) - E3-15 (CANN) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH]) |
OK
NG
Reconnect the L29 and L30 No. 2 CAN junction connectors.
NEXT
Disconnect the E70 No. 10 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E70-1 (CANH) - E70-12 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 10 Junction Connector) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E70-3 (CANH) - E70-14 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 10 Junction Connector) |
OK
NG
Reconnect the E70 No. 10 junction connector.
NEXT
Disconnect the E7 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E7-1 (MPX+) - E7-2 (MPX-) | Ignition switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
| Result | Proceed to |
|---|---|
| OK (w/ Multi-information Display) | A |
| OK (w/o Multi-information Display) | B |
| NG | C |
A
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL)
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL)
C
Reconnect the E70 No. 10 junction connector.
NEXT
Disconnect the E73 No. 9 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E73-1 (CANH) - E73-12 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 9 Junction Connector) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E73-2 (CANH) - E73-13 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 9 Junction Connector) |
OK
NG
Disconnect the E70 No. 10 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E3-16 (CANP) - E3-15 (CANN) | Ignition switch off | 108 to 132 Ω |
| E3-16 (CANP) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E3-15 (CANN) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E3-16 (CANP) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E3-15 (CANN) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Component with harness connected
(Main Body ECU [Cowl Side Junction Block LH]) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E70-3 (CANH) - E70-14 (CANN) | Ignition switch off | 108 to 132 Ω |
| E70-3 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E70-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E70-3 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E70-14 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 10 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E70 No. 10 junction connector.
NEXT
Disconnect the E73 No. 9 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E73-1 (CANH) - E73-12 (CANL) | Ignition switch off | 108 to 132 Ω |
| E73-1 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E73-12 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E73-1 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E73-12 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 9 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E3-16 (CANP) - E3-15 (CANN) | Ignition switch off | 108 to 132 Ω |
| E3-16 (CANP) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E3-15 (CANN) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E3-16 (CANP) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E3-15 (CANN) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Component with harness connected
(Main Body ECU [Cowl Side Junction Block LH]) |
| *b | Front view of DLC3 |
OK
NG
For vehicles without an rain sensor, go to "Check for Short in CAN Bus Wires (No. 9 Junction Connector - Accessory Bus Buffer)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E73-4 (CANH) - E73-15 (CANL) | Ignition switch off | 200 Ω or higher |
| E73-4 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E73-15 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E73-4 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E73-15 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 9 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E73-3 (CANH) - E73-14 (CANL) | Ignition switch off | 200 Ω or higher |
| E73-3 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E73-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E73-3 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E73-14 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 9 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E73 No. 9 junction connector.
NEXT
Disconnect the L30 No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L30-1 (CANH) - L30-2 (CANL) | Ignition switch off | 108 to 132 Ω |
| L30-1 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L30-2 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L30-1 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| L30-2 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the L29 No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E3-16 (CANP) - E3-15 (CANN) | Ignition switch off | 108 to 132 Ω |
| E3-16 (CANP) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E3-15 (CANN) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E3-16 (CANP) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E3-15 (CANN) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Component with harness connected
(Main Body ECU [Cowl Side Junction Block LH]) |
| *b | Front view of DLC3 |
OK
NG
For vehicles without a power back door system, go to "Check for Short in CAN Bus Wires (No. 2 CAN Junction Connector - Tire Pressure Warning ECU)".
Disconnect the L54 No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L54-1 (CANH) - L54-2 (CANL) | Ignition switch off | 200 Ω or higher |
| L54-1 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L54-2 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L54-1 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| L54-2 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the L57 No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L57-1 (CANH) - L57-2 (CANL) | Ignition switch off | 200 Ω or higher |
| L57-1 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L57-2 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L57-1 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| L57-2 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
For vehicles without a tire pressure warning system, go to "Replace No. 2 CAN Junction Connector".
Disconnect the L58 No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L58-1 (CANH) - L58-2 (CANL) | Ignition switch off | 200 Ω or higher |
| L58-1 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L58-2 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L58-1 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| L58-2 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the L29 and L30 No. 2 CAN junction connectors.
NEXT
Disconnect the E76 No. 8 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E76-1 (CANH) - E76-12 (CANL) | Ignition switch off | 108 to 132 Ω |
| E76-1 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E76-12 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E76-1 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E76-12 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 8 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
For vehicles without an entry and start system, go to "Check for Short in CAN Bus Wires (No. 8 Junction Connector - Position Control and Switch)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E76-2 (CANH) - E76-13 (CANL) | Ignition switch off | 200 Ω or higher |
| E76-2 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E76-13 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E76-2 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E76-13 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 8 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
For vehicles without seat memory, go to "Check for Short in CAN Bus Wires (No. 8 Junction Connector - Multiplex Tilt and Telescopic ECU)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E76-4 (CANH) - E76-15 (CANL) | Ignition switch off | 200 Ω or higher |
| E76-4 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E76-15 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E76-4 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E76-15 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 8 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E76-5 (CANH) - E76-16 (CANL) | Ignition switch off | 200 Ω or higher |
| E76-5 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E76-16 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E76-5 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E76-16 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 8 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
For vehicles without a power tilt and power telescopic steering column system, go to "Check for Short in CAN Bus Wires (No. 8 Junction Connector - Main Body ECU)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E76-3 (CANH) - E76-14 (CANL) | Ignition switch off | 200 Ω or higher |
| E76-3 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E76-14 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E76-3 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E76-14 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 8 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E76-6 (CANH) - E76-17 (CANL) | Ignition switch off | 108 to 132 Ω |
| E76-6 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E76-17 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E76-6 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E76-17 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 8 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E70 No. 10 junction connector.
NEXT
Disconnect the E7 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E7-1 (MPX+) - E7-2 (MPX-) | Ignition switch off | 108 to 132 Ω |
| E7-1 (MPX+) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E7-2 (MPX-) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E7-1 (MPX+) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E7-2 (MPX-) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK (w/ Multi-information Display) | A |
| OK (w/o Multi-information Display) | B |
| NG | C |
A
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL)
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL)
C
Reconnect the E73 No. 9 junction connector.
NEXT
Disconnect the E85 windshield wiper ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E85-6 (CANH) - E85-5 (CANL) | Ignition switch off | 54 to 69 Ω |
| E85-6 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E85-5 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E85-6 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E85-5 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector
(to Windshield Wiper ECU) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E73 No. 9 junction connector.
NEXT
Disconnect the E6 accessory bus buffer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E6-1 (CAN+) - E6-2 (CAN-) | Ignition switch off | 54 to 69 Ω |
| E6-1 (CAN+) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E6-2 (CAN-) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E6-1 (CAN+) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E6-2 (CAN-) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector
(to Accessory Bus Buffer) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the L29, L30 and L54 No. 2 CAN junction connectors.
NEXT
Disconnect the L52 power back door unit assembly (power back door ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L52-6 (MPX1) - L52-5 (MPX2) | Ignition switch off | 54 to 69 Ω |
| L52-6 (MPX1) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L52-5 (MPX2) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L52-6 (MPX1) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| L52-5 (MPX2) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU]) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the L29, L30, L54 and L57 No. 2 CAN junction connectors.
NEXT
Disconnect the L50 No. 2 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L50-11 (MPX+) - L50-12 (MPX-) | Ignition switch off | 54 to 69 Ω |
| L50-11 (MPX+) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L50-12 (MPX-) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L50-11 (MPX+) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| L50-12 (MPX-) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 Main Body ECU) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the L29, L30, L54, L57 and L58 No. 2 CAN junction connectors.
NEXT
Disconnect the L60 tire pressure warning ECU and receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L60-3 (CP1) - L60-6 (CN1) | Ignition switch off | 54 to 69 Ω |
| L60-3 (CP1) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L60-6 (CN1) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| L60-3 (CP1) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| L60-6 (CN1) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E76 No. 8 junction connector.
NEXT
Disconnect the E29 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E29-27 (CANH) - E29-28 (CANL) | Ignition switch off | 54 to 69 Ω |
| E29-27 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E29-28 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E29-27 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E29-28 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly]) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E76 No. 8 junction connector.
NEXT
Disconnect the c15 position control ECU and switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| c15-5 (MPX1) - c15-1 (MPX2) | Ignition switch off | 54 to 69 Ω |
| c15-5 (MPX1) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| c15-1 (MPX2) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| c15-5 (MPX1) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| c15-1 (MPX2) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector
(to Position Control ECU and Switch) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E76 No. 8 junction connector.
NEXT
Disconnect the I18 outer mirror control ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I18-1 (CANH) - I18-21 (CANL) | Ignition switch off | 54 to 69 Ω |
| I18-1 (CANH) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| I18-21 (CANL) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| I18-1 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| I18-21 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E76 No. 8 junction connector.
NEXT
Disconnect the E27 multiplex tilt and telescopic ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E27-5 (CANP) - E27-14 (CANN) | Ignition switch off | 54 to 69 Ω |
| E27-5 (CANP) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E27-14 (CANN) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E27-5 (CANP) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E27-14 (CANN) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E76 No. 8 junction connector.
NEXT
Disconnect the E3 main body ECU (cowl side junction block LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E3-16 (CANP) - E3-15 (CANN) | Ignition switch off | 108 to 132 Ω |
| E3-16 (CANP) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E3-15 (CANN) - E22-4 (CG) | Ignition switch off | 200 Ω or higher |
| E3-16 (CANP) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E3-15 (CANN) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH]) |
| *b | Front view of DLC3 |
OK
NG
Connect the cable to the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH]) |
*b | Rear view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH]) |
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the E3, 2A and 2D main body ECU (cowl side junction block LH) connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2A-1 (ALTB) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2D-62 (GND2) - Body ground | Always | Below 1 Ω |
| E3-1 (GND3) - Body ground | Always | Below 1 Ω |
OK
NG