There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
| Symptom | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ. | ·
Short between CAN bus lines and +B ·
ECM ·
Center airbag sensor assembly*1 ·
Headlight swivel ECU assembly*2 ·
Multi-media module receiver assembly*3 ·
Air conditioning amplifier assembly ·
Network gateway ECU ·
Main body ECU (cowl side junction block LH) ·
Combination meter assembly ·
No. 1 junction connector ·
No. 2 junction connector ·
No. 3 junction connector |
*1: w/ Airbag System
*2: w/ Dynamic Headlight Auto Leveling
*3: w/ Navigation System
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
NEXT
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
For vehicles with an SRS system:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
NEXT
Disconnect the E75 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E22-6 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E22-14 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of DLC3 |
OK
NG
Reconnect the E75 No. 3 junction connector.
NEXT
Disconnect the E72 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E22-6 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E22-14 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of DLC3 |
OK
NG
For vehicles without an airbag system, go to "Check for Short to B+ in CAN Bus Wire (No. 1 Junction Connector - Main Body ECU)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-4 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E72-15 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-3 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E72-14 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-2 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E72-13 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E47 center airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-4 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E72-15 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E3 main body ECU (cowl side junction block LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-3 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E72-14 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the A52 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E72-2 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E72-13 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK (for 1GR-FE) | A |
| OK (for 1UR-FE) | B |
| OK (for 1VD-FTV) | C |
| NG | D |
A
B
C
D
Reconnect the E72 No. 1 junction connector.
NEXT
Disconnect the E69 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-4 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E69-15 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E22-6 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E22-14 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of DLC3 |
OK
NG
For vehicles without an navigation system, go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Air Conditioning Amplifier)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-2 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E69-13 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-5 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E69-16 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
For vehicles without an dynamic headlight auto leveling, go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Network Gateway ECU)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-7 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E69-18 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-3 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E69-14 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the F77 multi-media module receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-2 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E69-13 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E35*1 or E81*2 air conditioning amplifier connector.
*1: w/ Rear Air Conditioning System
*2: w/o Rear Air Conditioning System
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-5 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E69-16 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E101 headlight swivel ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-7 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E69-18 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E31 network gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E69-3 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E69-14 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E69 No. 2 junction connector.
NEXT
Disconnect the E75 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-1 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E75-12 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-3 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E75-14 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Disconnect the E7 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E75-3 (CANH) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| E75-14 (CANL) - E22-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK (w/ Multi-information Display) | A |
| OK (w/o Multi-information Display) | B |
| NG | C |
A
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL)
B
(See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL)
C