Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255534 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Short to GND in CAN Bus Line  


DESCRIPTION

There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
·

Short between CAN bus lines and GND

·

ECM

·

Center airbag sensor assembly*1

·

Headlight swivel ECU assembly*2

·

Multi-media module receiver assembly*3

·

Air conditioning amplifier assembly

·

Network gateway ECU

·

Main body ECU (cowl side junction block LH)

·

Combination meter assembly

·

No. 1 junction connector

·

No. 2 junction connector

·

No. 3 junction connector



*1: w/ Airbag System

*2: w/ Dynamic Headlight Auto Leveling

*3: w/ Navigation System


WIRING DIAGRAM

C260052E01
6.055,1.348 6.429,1.495 0.374,0.147 10 ECM 2.748,3.157 4.370,3.315 1.622,0.158 10 No. 1 Junction Connector 2.748,2.985 3.038,3.166 0.290,0.181 10 E72 2.748,8.025 4.370,8.183 1.622,0.158 10 No. 2 Junction Connector 2.748,7.852 3.038,8.034 0.290,0.181 10 E69 5.873,0.298 6.338,0.440 0.465,0.141 10 CANH 6.057,1.21 6.370,1.353 0.313,0.143 10 A52 3.85,0.294 4.050,0.464 0.200,0.170 10 2 3.85,0.75 4.050,0.921 0.200,0.170 10 13 3.85,2.101 4.050,2.272 0.200,0.170 10 1 3.85,2.558 4.050,2.728 0.200,0.170 10 12 3.85,3.653 4.050,3.823 0.200,0.170 10 4 3.85,4.109 4.050,4.280 0.200,0.170 10 15 3.09,3.653 3.191,3.823 0.100,0.170 10 2 3.018,4.109 3.190,4.280 0.172,0.170 10 13 3.85,5.481 4.050,5.652 0.200,0.170 10 3 3.85,5.938 4.050,6.108 0.200,0.170 10 14 5.587,5.481 5.764,5.652 0.177,0.170 10 16 5.587,5.938 5.764,6.108 0.177,0.170 10 15 3.09,5.481 3.191,5.652 0.100,0.170 10 5 3.018,5.938 3.190,6.108 0.172,0.170 10 16 5.873,0.938 6.338,1.079 0.465,0.141 10 CANL 3.092,0.294 3.191,0.464 0.098,0.170 10 3 3.014,0.75 3.190,0.921 0.176,0.170 10 14 0.184,1.363 1.722,1.666 1.538,0.304 10 Main Body ECU (Cowl Side Junction Block LH) 0.184,1.197 0.528,1.366 0.345,0.169 10 E3 1.254,0.305 1.426,0.443 0.172,0.138 10 5 1.254,0.756 1.426,0.894 0.172,0.138 10 6 0.694,0.399 1.113,0.536 0.418,0.137 10 CANH 0.717,0.848 1.113,0.985 0.396,0.137 10 CANL 5.522,8.025 6.921,8.329 1.399,0.304 10 Headlight Swivel ECU Assembly*7 5.522,7.852 5.866,8.021 0.345,0.169 10 E101 5.592,6.988 5.764,7.126 0.172,0.138 10 12 5.592,7.439 5.764,7.577 0.172,0.138 10 13 5.873,7.068 6.291,7.205 0.419,0.137 10 MPX1 5.873,7.518 6.268,7.654 0.396,0.137 10 MPX2 3.094,2.101 3.191,2.272 0.097,0.170 10 4 3.018,2.558 3.190,2.728 0.172,0.170 10 15 0.184,3.17 2.338,3.321 2.155,0.151 10 Center Airbag Sensor Assembly*3 0.184,3.004 0.487,3.173 0.303,0.169 10 E47 1.254,2.113 1.426,2.251 0.172,0.138 10 13 1.254,2.563 1.426,2.701 0.172,0.138 10 22 0.694,2.207 1.113,2.344 0.418,0.137 10 CANH 0.717,2.656 1.113,2.793 0.396,0.137 10 CANL 0.184,4.711 2.005,5.015 1.821,0.304 10 Multi-media Module Receiver Assembly*4 0.184,4.544 0.487,4.713 0.303,0.169 10 F77 1.254,3.653 1.426,3.791 0.172,0.138 10 1 1.254,4.103 1.426,4.242 0.172,0.138 10 2 0.694,3.747 1.113,3.884 0.418,0.137 10 CANH 0.717,4.196 1.113,4.333 0.396,0.137 10 CANL 5.089,0.276 5.759,0.421 0.670,0.145 10 10*1, 41*2 5.089,0.747 5.759,0.893 0.670,0.145 10 11*1, 49*2 0.101,6.95 1.761,7.096 1.661,0.147 10 *1: except 1VD-FTV 0.101,7.487 1.761,7.634 1.661,0.147 10 *3: w/ Airbag System 0.101,7.218 1.761,7.365 1.661,0.147 10 *2: for 1VD-FTV 0.101,8.561 2.706,8.708 2.605,0.147 10 *7: w/ Dynamic Headlight Auto Leveling 0.101,7.756 1.677,7.902 1.576,0.147 10 *4: w/ Navigation System 0.101,8.024 2.349,8.171 2.248,0.147 10 *5: w/ Rear Air Conditioning System 0.101,8.293 2.432,8.439 2.332,0.147 10 *6: w/o Rear Air Conditioning System 0.184,6.406 2.442,6.555 2.259,0.149 10 Air Conditioning Amplifier Assembly 1.269,6.041 1.540,6.177 0.270,0.136 10 E35 1.291,5.841 1.518,5.978 0.227,0.136 10 4*5 1.269,5.587 1.540,5.724 0.270,0.136 10 E35 1.291,5.388 1.518,5.524 0.227,0.136 10 3*5 1.657,6.041 1.927,6.177 0.270,0.136 10 E81 1.64,5.841 1.944,5.978 0.303,0.136 10 12*6 1.657,5.587 1.927,5.724 0.270,0.136 10 E81 1.639,5.388 1.945,5.524 0.307,0.136 10 11*6 5.873,5.588 6.291,5.725 0.419,0.137 10 CA1H 5.873,6.038 6.268,6.175 0.396,0.137 10 CA1L 0.694,5.588 1.113,5.725 0.418,0.137 10 CANH 0.717,6.038 1.113,6.175 0.396,0.137 10 CANL 5.54,6.537 7.014,6.679 1.474,0.142 10 Network Gateway ECU 5.54,6.37 5.843,6.539 0.303,0.169 10 E31 3.09,6.975 3.191,7.145 0.100,0.170 10 1 3.018,7.431 3.190,7.602 0.172,0.170 10 12 3.85,6.975 3.951,7.145 0.100,0.170 10 7 3.85,7.431 4.022,7.602 0.172,0.170 10 18

C260053E01
5.69,4.03 6.890,4.335 1.200,0.305 10 Combination Meter Assembly 2.747,4.055 4.369,4.212 1.622,0.158 10 No. 3 Junction Connector 2.747,3.897 3.037,4.037 0.290,0.140 10 E75 5.872,2.981 6.337,3.122 0.465,0.141 10 CANH 5.692,3.893 6.005,4.035 0.313,0.143 10 E7 3.863,1.104 4.063,1.274 0.200,0.170 10 2 3.863,1.518 4.063,1.688 0.200,0.170 10 13 3.863,2.986 4.063,3.156 0.200,0.170 10 3 3.863,3.428 4.063,3.599 0.200,0.170 10 14 5.872,3.621 6.337,3.762 0.465,0.141 10 CANL 3.078,1.104 3.176,1.274 0.098,0.170 10 1 3,1.518 3.175,1.688 0.176,0.170 10 12 6.035,2.191 6.409,2.342 0.375,0.151 10 DLC3 6.035,2.034 6.338,2.178 0.303,0.144 10 E22 5.579,2.986 5.758,3.131 0.179,0.145 10 25 5.579,3.428 5.758,3.574 0.179,0.145 10 26 5.662,1.104 5.759,1.274 0.097,0.170 10 6 5.572,1.518 5.744,1.689 0.172,0.170 10 14 5.872,1.211 6.291,1.348 0.418,0.137 10 CANH 5.872,1.646 6.268,1.783 0.396,0.137 10 CANL

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
a.
C253362C24
0.167,1.01 0.563,1.271 0.396,0.26 1.948,0.917 2.135,0.427 2.135,0.427 2.271,0.427 false 1.948,1.458 1.802,1.885 1.802,1.885 1.667,1.885 false 1.573,0.896 1.427,0.438 1.427,0.438 1.292,0.438 false 0.052,0.031 0.219,0.219 0.167,0.188 10 false *a 2.333,0.344 2.802,0.531 0.469,0.188 10 false CANH 1.26,1.813 1.667,2 0.406,0.188 10 false CANL 0.229,1.063 0.552,1.271 0.323,0.208 10 false E22 1.031,0.344 1.5,0.531 0.469,0.188 10 false CG

Disconnect the E75 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E22-6 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E22-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Front view of DLC3



OK

4.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

4.CONNECT CONNECTOR
a.

Reconnect the E75 No. 3 junction connector.



NEXT

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)
a.
C253362C24
0.167,1.01 0.563,1.271 0.396,0.26 1.948,0.917 2.135,0.427 2.135,0.427 2.271,0.427 false 1.948,1.458 1.802,1.885 1.802,1.885 1.667,1.885 false 1.573,0.896 1.427,0.438 1.427,0.438 1.292,0.438 false 0.052,0.031 0.219,0.219 0.167,0.188 10 false *a 2.333,0.344 2.802,0.531 0.469,0.188 10 false CANH 1.26,1.813 1.667,2 0.406,0.188 10 false CANL 0.229,1.063 0.552,1.271 0.323,0.208 10 false E22 1.031,0.344 1.5,0.531 0.469,0.188 10 false CG

Disconnect the E72 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E22-6 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E22-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Front view of DLC3



OK

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

NG

12.CONNECT CONNECTOR
6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)
NOTICE:

For vehicles without an airbag system, go to "Check for Short to GND in CAN Bus Wire (No. 1 Junction Connector - Main Body ECU)".


a.
U165320E02
1.646,2.51 1.365,2.167 1.365,2.167 1.198,2.167 false 1.906,1.104 2.219,0.823 2.219,0.823 2.385,0.823 false 1.906,1.292 2.219,1.594 2.219,1.594 2.385,1.594 false 0.917,2.073 1.323,2.271 0.406,0.198 10 false CG 2.427,0.74 2.948,0.938 0.521,0.198 10 false CANH 2.427,1.51 2.938,1.75 0.51,0.24 10 false CANL 0.063,0.052 0.479,0.24 0.417,0.188 10 false *a 0.063,1.75 0.5,1.958 0.438,0.208 10 false *b 0.604,1.094 0.969,1.333 0.365,0.24 10 false E72 0.427,2.667 0.792,2.917 0.365,0.25 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-4 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E72-15 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U165319E02
1.635,2.5 1.354,2.156 1.354,2.156 1.188,2.156 false 2,1.115 2.313,0.833 2.313,0.833 2.49,0.833 false 2,1.292 2.313,1.594 2.313,1.594 2.49,1.594 false 0.854,2.073 1.25,2.25 0.396,0.177 10 false CG 2.521,0.76 2.99,0.958 0.469,0.198 10 false CANH 2.521,1.521 3,1.75 0.479,0.229 10 false CANL 0.063,0.052 0.479,0.198 0.417,0.146 10 false *a 0.063,1.75 0.479,1.896 0.417,0.146 10 false *b 0.604,1.104 0.969,1.333 0.365,0.229 10 false E72 0.427,2.667 0.802,2.906 0.375,0.24 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E72-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)

NG

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU)
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)
a.
U165321E02
1.635,2.51 1.354,2.167 1.354,2.167 1.188,2.167 false 2.104,1.104 2.354,0.917 2.354,0.917 2.521,0.917 false 2.104,1.292 2.354,1.479 2.354,1.479 2.521,1.479 false 0.896,2.083 1.24,2.292 0.344,0.208 10 false CG 2.552,0.833 3.073,1.052 0.521,0.219 10 false CANH 2.552,1.385 3.104,1.604 0.552,0.219 10 false CANL 0.063,0.063 0.49,0.271 0.427,0.208 10 false *a 0.063,1.75 0.479,1.969 0.417,0.219 10 false *b 0.604,1.104 0.969,1.354 0.365,0.25 10 false E72 0.427,2.656 0.771,2.885 0.344,0.229 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-2 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E72-13 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)
9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
a.
U165320E02
1.646,2.51 1.365,2.167 1.365,2.167 1.198,2.167 false 1.906,1.104 2.219,0.823 2.219,0.823 2.385,0.823 false 1.906,1.292 2.219,1.594 2.219,1.594 2.385,1.594 false 0.917,2.073 1.323,2.271 0.406,0.198 10 false CG 2.427,0.74 2.948,0.938 0.521,0.198 10 false CANH 2.427,1.51 2.938,1.75 0.51,0.24 10 false CANL 0.063,0.052 0.479,0.24 0.417,0.188 10 false *a 0.063,1.75 0.5,1.958 0.438,0.208 10 false *b 0.604,1.094 0.969,1.333 0.365,0.24 10 false E72 0.427,2.667 0.792,2.917 0.365,0.25 10 false E22

Disconnect the E47 center airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-4 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E72-15 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU)
a.
U165319E02
1.635,2.5 1.354,2.156 1.354,2.156 1.188,2.156 false 2,1.115 2.313,0.833 2.313,0.833 2.49,0.833 false 2,1.292 2.313,1.594 2.313,1.594 2.49,1.594 false 0.854,2.073 1.25,2.25 0.396,0.177 10 false CG 2.521,0.76 2.99,0.958 0.469,0.198 10 false CANH 2.521,1.521 3,1.75 0.479,0.229 10 false CANL 0.063,0.052 0.479,0.198 0.417,0.146 10 false *a 0.063,1.75 0.479,1.896 0.417,0.146 10 false *b 0.604,1.104 0.969,1.333 0.365,0.229 10 false E72 0.427,2.667 0.802,2.906 0.375,0.24 10 false E22

Disconnect the E3 main body ECU (cowl side junction block LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E72-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)
a.
U165321E02
1.635,2.51 1.354,2.167 1.354,2.167 1.188,2.167 false 2.104,1.104 2.354,0.917 2.354,0.917 2.521,0.917 false 2.104,1.292 2.354,1.479 2.354,1.479 2.521,1.479 false 0.896,2.083 1.24,2.292 0.344,0.208 10 false CG 2.552,0.833 3.073,1.052 0.521,0.219 10 false CANH 2.552,1.385 3.104,1.604 0.552,0.219 10 false CANL 0.063,0.063 0.49,0.271 0.427,0.208 10 false *a 0.063,1.75 0.479,1.969 0.417,0.219 10 false *b 0.604,1.104 0.969,1.354 0.365,0.25 10 false E72 0.427,2.656 0.771,2.885 0.344,0.229 10 false E22

Disconnect the A52 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E72-2 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E72-13 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3

Result
Result Proceed to
OK (for 1GR-FE) A
OK (for 1UR-FE) B
OK (for 1VD-FTV) C
NG D



A

B

C

D

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

12.CONNECT CONNECTOR
a.

Reconnect the E72 No. 1 junction connector.



NEXT

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.
U165359E02
1.917,1.115 2.333,0.771 2.333,0.771 2.5,0.771 false 1.917,1.271 2.208,1.594 2.208,1.594 2.385,1.594 false 1.646,2.5 1.417,2.104 1.417,2.104 1.24,2.104 false 2.552,0.688 3.135,0.885 0.583,0.198 10 false CANH 2.438,1.51 3.031,1.708 0.594,0.198 10 false CANL 0.938,2.01 1.292,2.188 0.354,0.177 10 false CG 0.063,0.052 0.542,0.26 0.479,0.208 10 false *a 0.063,1.75 0.521,1.938 0.458,0.188 10 false *b 0.604,1.094 0.958,1.292 0.354,0.198 10 false E69 0.417,2.656 0.781,2.854 0.365,0.198 10 false E22

Disconnect the E69 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-4 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E69-15 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)
a.
C253362C24
0.167,1.01 0.563,1.271 0.396,0.26 1.948,0.917 2.135,0.427 2.135,0.427 2.271,0.427 false 1.948,1.458 1.802,1.885 1.802,1.885 1.667,1.885 false 1.573,0.896 1.427,0.438 1.427,0.438 1.292,0.438 false 0.052,0.031 0.219,0.219 0.167,0.188 10 false *a 2.333,0.344 2.802,0.531 0.469,0.188 10 false CANH 1.26,1.813 1.667,2 0.406,0.188 10 false CANL 0.229,1.063 0.552,1.271 0.323,0.208 10 false E22 1.031,0.344 1.5,0.531 0.469,0.188 10 false CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E22-6 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E22-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Front view of DLC3



OK

15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

NG

23.CONNECT CONNECTOR
15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)
NOTICE:

For vehicles without an navigation system, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Air Conditioning Amplifier)".


a.
U165323E02
1.646,2.5 1.365,2.156 1.365,2.156 1.198,2.156 false 2.104,1.104 2.313,0.906 2.313,0.906 2.49,0.906 false 2.104,1.281 2.313,1.49 2.313,1.49 2.49,1.49 false 0.906,2.063 1.344,2.26 0.438,0.198 10 false CG 2.531,0.813 3.094,1.042 0.563,0.229 10 false CANH 2.531,1.396 3.063,1.635 0.531,0.24 10 false CANL 0.063,0.042 0.531,0.271 0.469,0.229 10 false *a 0.063,1.75 0.479,1.938 0.417,0.188 10 false *b 0.604,1.094 0.979,1.333 0.375,0.24 10 false E69 0.427,2.656 0.771,2.875 0.344,0.219 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-2 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E69-13 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)
16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U165324E02
1.646,2.5 1.365,2.156 1.365,2.156 1.198,2.156 false 1.813,1.104 2.281,0.656 2.281,0.656 2.448,0.656 false 1.823,1.292 2.135,1.635 2.135,1.635 2.302,1.635 false 0.885,2.083 1.302,2.292 0.417,0.208 10 false CG 2.49,0.573 3.052,0.792 0.563,0.219 10 false CANH 2.333,1.552 2.865,1.781 0.531,0.229 10 false CANL 0.063,0.042 0.49,0.25 0.427,0.208 10 false *a 0.063,1.75 0.479,1.948 0.417,0.198 10 false *b 0.615,1.104 1.021,1.333 0.406,0.229 10 false E69 0.427,2.656 0.792,2.885 0.365,0.229 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-5 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E69-16 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)

NG

20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)
NOTICE:

For vehicles without an dynamic headlight auto leveling, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Network Gateway ECU)".


a.
U165360E02
1.615,1.104 1.156,0.667 1.156,0.667 0.979,0.667 false 1.615,1.271 1.302,1.573 1.302,1.573 1.135,1.573 false 1.646,2.51 1.406,2.125 1.406,2.125 1.24,2.125 false 0.469,0.573 0.979,0.76 0.51,0.188 10 false CANH 0.646,1.51 1.167,1.74 0.521,0.229 10 false CANL 0.917,2.052 1.333,2.198 0.417,0.146 10 false CG 0.063,0.052 0.521,0.25 0.458,0.198 10 false *a 0.063,1.75 0.5,1.938 0.438,0.188 10 false *b 2.615,1.094 3.063,1.292 0.448,0.198 10 false E69 0.417,2.656 0.875,2.844 0.458,0.188 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-7 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E69-18 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NG

21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (HEADLIGHT SWIVEL ECU ASSEMBLY)
18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U165325E02
1.646,2.51 1.365,2.167 1.365,2.167 1.198,2.167 false 2,1.104 2.313,0.823 2.313,0.823 2.49,0.823 false 2,1.292 2.313,1.594 2.313,1.594 2.49,1.594 false 0.906,2.094 1.365,2.302 0.458,0.208 10 false CG 2.531,0.74 3.156,0.979 0.625,0.24 10 false CANH 2.521,1.5 3.073,1.698 0.552,0.198 10 false CANL 0.063,0.042 0.531,0.24 0.469,0.198 10 false *a 0.063,1.75 0.521,1.938 0.458,0.188 10 false *b 0.604,1.094 1.052,1.333 0.448,0.24 10 false E69 0.427,2.656 0.875,2.896 0.448,0.24 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E69-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NETWORK GATEWAY ECU)
19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)
a.
U165323E02
1.646,2.5 1.365,2.156 1.365,2.156 1.198,2.156 false 2.104,1.104 2.313,0.906 2.313,0.906 2.49,0.906 false 2.104,1.281 2.313,1.49 2.313,1.49 2.49,1.49 false 0.906,2.063 1.344,2.26 0.438,0.198 10 false CG 2.531,0.813 3.094,1.042 0.563,0.229 10 false CANH 2.531,1.396 3.063,1.635 0.531,0.24 10 false CANL 0.063,0.042 0.531,0.271 0.469,0.229 10 false *a 0.063,1.75 0.479,1.938 0.417,0.188 10 false *b 0.604,1.094 0.979,1.333 0.375,0.24 10 false E69 0.427,2.656 0.771,2.875 0.344,0.219 10 false E22

Disconnect the F77 multi-media module receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-2 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E69-13 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CANH, CANL)

20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U165324E02
1.646,2.5 1.365,2.156 1.365,2.156 1.198,2.156 false 1.813,1.104 2.281,0.656 2.281,0.656 2.448,0.656 false 1.823,1.292 2.135,1.635 2.135,1.635 2.302,1.635 false 0.885,2.083 1.302,2.292 0.417,0.208 10 false CG 2.49,0.573 3.052,0.792 0.563,0.219 10 false CANH 2.333,1.552 2.865,1.781 0.531,0.229 10 false CANL 0.063,0.042 0.49,0.25 0.427,0.208 10 false *a 0.063,1.75 0.479,1.948 0.417,0.198 10 false *b 0.615,1.104 1.021,1.333 0.406,0.229 10 false E69 0.427,2.656 0.792,2.885 0.365,0.229 10 false E22

Disconnect the E35*1 or E81*2 air conditioning amplifier connector.

*1: w/ Rear Air Conditioning System

*2: w/o Rear Air Conditioning System



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-5 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E69-16 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (HEADLIGHT SWIVEL ECU ASSEMBLY)
a.
U165360E02
1.615,1.104 1.156,0.667 1.156,0.667 0.979,0.667 false 1.615,1.271 1.302,1.573 1.302,1.573 1.135,1.573 false 1.646,2.51 1.406,2.125 1.406,2.125 1.24,2.125 false 0.469,0.573 0.979,0.76 0.51,0.188 10 false CANH 0.646,1.51 1.167,1.74 0.521,0.229 10 false CANL 0.917,2.052 1.333,2.198 0.417,0.146 10 false CG 0.063,0.052 0.521,0.25 0.458,0.198 10 false *a 0.063,1.75 0.5,1.938 0.438,0.188 10 false *b 2.615,1.094 3.063,1.292 0.448,0.198 10 false E69 0.417,2.656 0.875,2.844 0.458,0.188 10 false E22

Disconnect the E101 headlight swivel ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-7 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E69-18 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT SWIVEL ECU ASSEMBLY (MPX1, MPX2)

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NETWORK GATEWAY ECU)
a.
U165325E02
1.646,2.51 1.365,2.167 1.365,2.167 1.198,2.167 false 2,1.104 2.313,0.823 2.313,0.823 2.49,0.823 false 2,1.292 2.313,1.594 2.313,1.594 2.49,1.594 false 0.906,2.094 1.365,2.302 0.458,0.208 10 false CG 2.531,0.74 3.156,0.979 0.625,0.24 10 false CANH 2.521,1.5 3.073,1.698 0.552,0.198 10 false CANL 0.063,0.042 0.531,0.24 0.469,0.198 10 false *a 0.063,1.75 0.521,1.938 0.458,0.188 10 false *b 0.604,1.094 1.052,1.333 0.448,0.24 10 false E69 0.427,2.656 0.875,2.896 0.448,0.24 10 false E22

Disconnect the E31 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E69-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E69-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CANH, CANL)

23.CONNECT CONNECTOR
a.

Reconnect the E69 No. 2 junction connector.



NEXT

24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U165326E02
1.646,2.51 1.365,2.167 1.365,2.167 1.198,2.167 false 2.198,1.104 2.396,0.927 2.396,0.927 2.563,0.927 false 2.198,1.292 2.344,1.5 2.344,1.5 2.51,1.5 false 0.875,2.094 1.313,2.271 0.438,0.177 10 false CG 2.583,0.844 3.104,1.031 0.521,0.188 10 false CANH 2.542,1.406 3.104,1.615 0.563,0.208 10 false CANL 0.063,0.083 0.51,0.281 0.448,0.198 10 false *a 0.063,1.75 0.51,1.938 0.448,0.188 10 false *b 0.615,1.094 1.031,1.302 0.417,0.208 10 false E75 0.427,2.656 0.823,2.906 0.396,0.25 10 false E22

Disconnect the E75 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-1 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E75-12 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

25.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

25.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U165328E02
1.635,2.5 1.354,2.156 1.354,2.156 1.188,2.156 false 2.01,1.115 2.323,0.833 2.323,0.833 2.5,0.833 false 2.01,1.281 2.323,1.583 2.323,1.583 2.5,1.583 false 0.906,2.073 1.333,2.24 0.427,0.167 10 false CG 2.521,0.74 3.083,0.938 0.563,0.198 10 false CANH 2.542,1.5 3.073,1.698 0.531,0.198 10 false CANL 0.063,0.063 0.479,0.25 0.417,0.188 10 false *a 0.063,1.75 0.479,1.948 0.417,0.198 10 false *b 0.615,1.094 1,1.302 0.385,0.208 10 false E75 0.438,2.667 0.781,2.885 0.344,0.219 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E75-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
a.
U165328E02
1.635,2.5 1.354,2.156 1.354,2.156 1.188,2.156 false 2.01,1.115 2.323,0.833 2.323,0.833 2.5,0.833 false 2.01,1.281 2.323,1.583 2.323,1.583 2.5,1.583 false 0.906,2.073 1.333,2.24 0.427,0.167 10 false CG 2.521,0.74 3.083,0.938 0.563,0.198 10 false CANH 2.542,1.5 3.073,1.698 0.531,0.198 10 false CANL 0.063,0.063 0.479,0.25 0.417,0.188 10 false *a 0.063,1.75 0.479,1.948 0.417,0.198 10 false *b 0.615,1.094 1,1.302 0.385,0.208 10 false E75 0.438,2.667 0.781,2.885 0.344,0.219 10 false E22

Disconnect the E7 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E75-3 (CANH) - E22-4 (CG) Ignition switch off 200 Ω or higher
E75-14 (CANL) - E22-4 (CG) Ignition switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3

Result
Result Proceed to
OK (w/ Multi-information Display) A
OK (w/o Multi-information Display) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)