Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Engine does not Start  


DESCRIPTION

ENGINE START SYSTEM OPERATION


a.

When the engine switch is pressed with the brake pedal depressed and the shift lever in P (for A/T) or the clutch pedal depressed (for M/T), the main body ECU determines that it is an engine start request.


b.

The certification ECU (smart key ECU assembly) and other ECUs perform key verification via the LIN communication line. The engine switch indicator light illuminates in green.


c.

The main body ECU activates the IG1 No. 3 relay, ACC relay and integration relay (IG2 relay).


d.

The certification ECU (smart key ECU assembly) outputs a steering unlock signal. The signal is sent to the steering lock ECU via the LIN communication line.


e.

The main body ECU sends an engine start request signal to the ECM.


f.

The main body ECU deactivates the ACC relay until the ECU detects an engine start.


g.

The ECU reactivates the ACC relay and turns off the engine switch indicator light.

Symbols of Main Body ECU Signals
SSW1/SSW2 Engine switch on (ACC, IG) signal
IG1D IG1 No. 3 relay operation signal
ACCD ACC relay operation signal
IG2D Integration relay (IG2 relay) operation signal
STP Stop light switch signal
P (for A/T) Shift lock signal
TACH Engine start detection signal
STSW Starter activation request signal
ACCR ACC cut request signal



C262551E01
5.044,0.868 6.009,1.053 0.964,0.185 10 Engine Switch 2.196,0.594 2.583,0.779 0.388,0.185 10 AM2 2.048,1.574 2.783,1.759 0.735,0.185 10 IG1 No. 3 2.915,1.315 3.337,1.500 0.422,0.185 10 IG1D 1.597,2.589 1.984,2.774 0.388,0.185 10 IG2 2.915,2.335 3.302,2.520 0.388,0.185 10 IG2D 0.939,3.601 1.443,3.786 0.504,0.185 10 ACC 2.915,3.353 3.419,3.538 0.504,0.185 10 ACCD 0.849,0.451 1.706,0.636 0.856,0.185 10 from Battery 2.915,0.366 3.275,0.551 0.360,0.185 10 AM1 2.915,0.534 3.275,0.719 0.360,0.185 10 AM2 3.98,0.366 4.419,0.551 0.439,0.185 10 SSW1 3.98,0.534 4.419,0.719 0.439,0.185 10 SSW2 0.099,8.509 4.990,8.679 4.891,0.170 10 *: These DTCs are stored when there is a malfunction in a related circuit 2.895,7.66 4.481,8.019 1.586,0.359 10 Main Body ECU (Cowl Side Junction Block LH) 3.118,0.195 3.640,0.380 0.521,0.185 10 B2271* 3.118,1.147 3.639,1.332 0.521,0.185 10 B2272* 3.795,0.195 4.316,0.380 0.521,0.185 10 B2278* 4.078,1.684 4.516,1.869 0.439,0.185 10 LIN1 4.755,2.336 5.276,2.521 0.521,0.185 10 B2285* 4.755,2.503 5.276,2.688 0.521,0.185 10 B2288* 4.755,3.88 5.276,4.065 0.521,0.185 10 B2289* 3.118,2.165 3.639,2.350 0.521,0.185 10 B2273* 3.118,3.183 3.639,3.368 0.521,0.185 10 B2274* 4.856,2.806 6.953,3.148 2.097,0.342 10 Steering Lock Actuator Assembly (Steering Lock ECU) 0.542,5.764 2.176,6.012 1.635,0.247 10 Shift Lock Control ECU 0.72,4.195 1.906,4.380 1.186,0.185 10 Stop Light Switch 0.692,5.022 2.012,5.207 1.320,0.185 10 Combination Meter 1.025,6.821 1.489,7.006 0.464,0.185 10 ECM 5.147,4.191 6.772,4.614 1.625,0.423 10 Certification ECU (Smart Key ECU Assembly) 5.105,1.426 6.702,1.872 1.597,0.446 10 ID Code Box (Immobiliser Code ECU) 5.838,5.496 6.153,5.680 0.315,0.185 10 Key 3.99,6.968 4.433,7.153 0.443,0.185 10 GND2 3.795,6.825 4.316,7.010 0.521,0.185 10 B2271* 3.118,5.749 3.639,5.933 0.521,0.185 10 B2281* 3.118,6.697 3.639,6.882 0.521,0.185 10 B2286* 0.42,7.726 2.123,7.896 1.703,0.170 10 : CAN Communication Line 3.99,6.107 4.464,6.292 0.473,0.185 10 CANH 3.99,6.606 4.464,6.791 0.473,0.185 10 CANL 2.915,6.84 3.425,7.025 0.510,0.185 10 TACH 3.132,7.121 3.653,7.306 0.521,0.185 10 B2276* 2.929,7.264 3.439,7.449 0.510,0.185 10 ACCR 3.118,6.311 3.639,6.496 0.521,0.185 10 B2275* 2.915,6.454 3.404,6.639 0.490,0.185 10 STSW 2.915,5.919 3.434,6.103 0.519,0.185 10 P 3.118,4.953 3.639,5.137 0.521,0.185 10 B2283* 2.915,5.123 3.434,5.307 0.519,0.185 10 SPD 3.118,4.781 3.639,4.966 0.521,0.185 10 B2282* 3.118,4.184 3.639,4.369 0.521,0.185 10 B2284* 2.915,4.355 3.434,4.539 0.520,0.185 10 STP 0.42,8.19 2.123,8.361 1.703,0.170 10 : LIN Communication Line

WIRING DIAGRAM

C262534E01
0.479,0.836 1.343,1.117 0.864,0.281 10 from Battery 0.11,0.097 0.849,0.263 0.739,0.166 12 for LHD: 1.782,1 2.202,1.225 0.420,0.225 10 AM2 3.267,0.864 3.701,1.089 0.434,0.225 10 AM1 3.267,1.459 3.687,1.685 0.420,0.225 10 AM2 3.879,6.244 4.178,6.469 0.299,0.225 10 STR 3.267,6.773 3.687,6.998 0.420,0.225 10 TACH 3.267,6.269 3.687,6.494 0.420,0.225 10 STSW 3.267,5.764 3.687,5.989 0.420,0.225 10 ACCR 3.267,4.691 3.687,4.917 0.420,0.225 10 SPD 3.267,3.638 3.687,3.863 0.420,0.225 10 SWIL 3.267,3.217 3.687,3.443 0.420,0.225 10 INDW 3.267,2.825 3.687,3.051 0.420,0.225 10 INDS 3.267,2.419 3.687,2.644 0.420,0.225 10 SSW2 3.267,2.006 3.687,2.231 0.420,0.225 10 SSW1 2.951,0.857 3.371,1.082 0.420,0.225 10 E1 3.757,1.116 4.177,1.341 0.420,0.225 10 ACCD 3.827,2.13 4.178,2.356 0.350,0.225 10 IG1D 3.827,2.979 4.178,3.205 0.350,0.225 10 IG2D 3.795,5.606 4.177,5.832 0.383,0.225 10 STR2 4.286,6.232 4.705,6.457 0.420,0.225 10 E1 2.958,6.759 3.378,6.984 0.420,0.225 10 E3 2.944,6.255 3.364,6.480 0.420,0.225 10 E4 2.937,5.757 3.357,5.982 0.420,0.225 10 E2 2.958,4.677 3.378,4.903 0.420,0.225 10 E3 0.922,4.976 1.341,5.136 0.420,0.160 10 E7 2.944,3.624 3.364,3.849 0.420,0.225 10 E1 2.944,3.203 3.364,3.429 0.420,0.225 10 E1 2.944,2.811 3.364,3.037 0.420,0.225 10 E1 2.944,2.405 3.364,2.630 0.420,0.225 10 E1 2.951,1.992 3.371,2.217 0.420,0.225 10 E1 2.944,1.438 3.364,1.663 0.420,0.225 10 E2 1.803,3.631 2.223,3.856 0.420,0.225 10 SWIL 1.221,3.161 1.641,3.387 0.420,0.225 10 GND 1.768,3.217 2.188,3.443 0.420,0.225 10 INDW 1.81,2.811 2.230,3.037 0.420,0.225 10 INDS 1.88,2.405 2.300,2.630 0.420,0.225 10 SS2 1.894,1.999 2.314,2.224 0.420,0.225 10 SS1 4.286,1.102 4.705,1.327 0.420,0.225 10 E1 4.286,2.116 4.705,2.342 0.420,0.225 10 E1 4.286,2.958 4.705,3.184 0.420,0.225 10 E2 4.274,5.603 4.693,5.829 0.420,0.225 10 E4 5.071,2.391 5.866,2.616 0.795,0.225 10 IG1 NO. 3 5.232,1.376 5.707,1.602 0.475,0.225 10 ACC 5.557,7.674 5.977,7.900 0.420,0.225 10 L 4.955,7.674 5.375,7.900 0.420,0.225 10 B 1.796,6.759 2.216,6.984 0.420,0.225 10 TACH 1.754,6.255 2.174,6.480 0.420,0.225 10 STSW 1.768,5.75 2.188,5.975 0.420,0.225 10 ACCR 1.985,4.684 2.280,4.910 0.295,0.225 10 +S 5.134,5.865 5.734,6.091 0.600,0.225 10 ST CUT 5.615,3.486 6.035,3.711 0.420,0.225 10 IG2 6.065,4.217 6.364,4.401 0.299,0.184 10 IGN 1.21,4.037 2.241,4.262 1.031,0.225 10 Engine Switch 0.922,5.121 2.175,5.284 1.253,0.164 10 Combination Meter 1.502,6.983 1.921,7.208 0.420,0.225 10 ECM 4.739,8.041 5.920,8.401 1.182,0.360 10 Park/Neutral Position Switch*5 2.994,6.584 3.275,6.809 0.281,0.225 10 8 2.994,6.079 3.275,6.305 0.281,0.225 10 4 2.994,5.575 3.275,5.800 0.281,0.225 10 3 0.997,3.063 1.278,3.289 0.281,0.225 10 5 2.244,3.54 2.525,3.765 0.281,0.225 10 11 2.244,3.119 2.525,3.345 0.281,0.225 10 13 2.244,2.727 2.525,2.952 0.281,0.225 10 12 2.244,2.321 2.525,2.546 0.281,0.225 10 2 2.244,1.922 2.525,2.147 0.281,0.225 10 7 2.994,4.509 3.275,4.734 0.281,0.225 10 9 2.954,3.456 3.235,3.681 0.281,0.225 10 25 2.954,3.035 3.235,3.261 0.281,0.225 10 14 2.954,2.636 3.235,2.861 0.281,0.225 10 15 2.954,2.23 3.235,2.455 0.281,0.225 10 16 2.954,1.816 3.235,2.042 0.281,0.225 10 17 2.994,1.27 3.275,1.495 0.281,0.225 10 1 2.994,0.689 3.275,0.914 0.281,0.225 10 6 5.739,7.602 6.020,7.828 0.281,0.225 10 5 4.332,6.048 4.613,6.273 0.281,0.225 10 8 6.204,3.474 6.485,3.700 0.281,0.225 10 8 4.919,2.769 5.200,2.995 0.281,0.225 10 6 6.202,2.775 6.483,3.000 0.281,0.225 10 7 4.918,3.491 5.199,3.716 0.281,0.225 10 1 4.868,3.292 5.149,3.517 0.281,0.225 10 1C 4.868,2.956 5.149,3.182 0.281,0.225 10 1B 6.155,2.956 6.436,3.182 0.281,0.225 10 1B 6.155,3.294 6.436,3.519 0.281,0.225 10 1B 5.008,5.523 5.289,5.749 0.281,0.225 10 5 5.673,5.529 5.954,5.755 0.281,0.225 10 3 5.663,5.333 5.944,5.558 0.281,0.225 10 1 5.008,5.327 5.289,5.552 0.281,0.225 10 2 4.78,7.595 5.061,7.821 0.281,0.225 10 4 4.297,0.934 4.578,1.159 0.281,0.225 10 22 4.336,1.948 4.617,2.173 0.281,0.225 10 3 4.297,2.79 4.578,3.016 0.281,0.225 10 11 4.336,5.424 4.617,5.649 0.281,0.225 10 6 2.263,4.594 2.544,4.819 0.281,0.225 10 4 1.2,6.557 1.620,6.782 0.420,0.225 10 STAR 1.21,3.883 1.630,4.108 0.420,0.225 10 E18 4.739,7.883 5.038,8.108 0.299,0.225 10 C24 4.91,6.816 5.789,7.141 0.879,0.324 10 Clutch Start Switch*4 5.739,6.407 6.020,6.632 0.281,0.225 10 2 4.78,6.4 5.061,6.625 0.281,0.225 10 1 4.91,6.676 5.209,6.826 0.299,0.151 10 A49 0.843,6.548 1.263,6.773 0.420,0.225 10 C45 2.272,6.759 2.692,6.984 0.420,0.225 10 A38 2.272,6.255 2.692,6.480 0.420,0.225 10 A38 2.272,5.75 2.692,5.975 0.420,0.225 10 A38 0.808,6.066 1.183,6.213 0.374,0.147 10 16*1 0.332,7.477 3.043,7.657 2.711,0.180 10 *1: for 1UR-FE, 1GR-FE, 3UR-FE 0.332,8.243 1.446,8.387 1.114,0.144 10 *4: for M/T 0.332,8.5 1.446,8.643 1.114,0.144 10 *5: for A/T 0.332,7.73 2.050,7.874 1.718,0.144 10 *2: for 1VD-FTV w/o DPF 0.332,7.987 1.911,8.130 1.579,0.144 10 *3: for 1VD-FTV w/ DPF 2.305,6.584 2.586,6.809 0.281,0.225 10 15 2.235,5.949 2.801,6.118 0.566,0.170 10 14*1, *2 2.245,5.219 2.572,5.398 0.328,0.179 10 41*1 5.156,3.413 5.575,3.747 0.420,0.334 10 IG2 MAIN 5.069,3.836 6.378,4.062 1.309,0.225 10 Integration Relay 2.945,8.205 4.490,8.542 1.545,0.337 10 Main Body ECU (Cowl Side Junction Block LH) 0.815,6.216 1.147,6.376 0.332,0.161 10 51*2 0.815,6.37 1.147,6.530 0.332,0.161 10 52*3 2.244,5.393 2.567,5.562 0.323,0.170 10 13*2 2.244,5.557 2.567,5.727 0.323,0.170 10 22*3 2.244,6.09 2.567,6.259 0.323,0.170 10 47*3

C262534E02
0.479,0.836 1.343,1.117 0.864,0.281 10 from Battery 0.11,0.097 0.849,0.263 0.739,0.166 12 for RHD: 1.782,1 2.202,1.225 0.420,0.225 10 AM2 3.267,0.864 3.701,1.089 0.434,0.225 10 AM1 3.267,1.459 3.687,1.685 0.420,0.225 10 AM2 3.879,6.244 4.178,6.469 0.299,0.225 10 STR 3.267,6.779 3.687,7.004 0.420,0.225 10 TACH 3.267,6.275 3.687,6.500 0.420,0.225 10 STSW 3.267,5.764 3.687,5.989 0.420,0.225 10 ACCR 3.267,4.691 3.687,4.917 0.420,0.225 10 SPD 3.267,3.638 3.687,3.863 0.420,0.225 10 SWIL 3.267,3.217 3.687,3.443 0.420,0.225 10 INDW 3.267,2.825 3.687,3.051 0.420,0.225 10 INDS 3.267,2.419 3.687,2.644 0.420,0.225 10 SSW2 3.267,2.006 3.687,2.231 0.420,0.225 10 SSW1 2.951,0.857 3.371,1.082 0.420,0.225 10 E1 3.757,1.116 4.177,1.341 0.420,0.225 10 ACCD 3.827,2.13 4.178,2.356 0.350,0.225 10 IG1D 3.827,2.979 4.178,3.205 0.350,0.225 10 IG2D 3.795,5.606 4.177,5.832 0.383,0.225 10 STR2 4.286,6.232 4.705,6.457 0.420,0.225 10 E1 2.958,6.765 3.378,6.990 0.420,0.225 10 E3 2.944,6.261 3.364,6.486 0.420,0.225 10 E4 2.937,5.757 3.357,5.982 0.420,0.225 10 E2 2.958,4.677 3.378,4.903 0.420,0.225 10 E3 0.922,4.976 1.341,5.136 0.420,0.160 10 E7 2.944,3.624 3.364,3.849 0.420,0.225 10 E1 2.944,3.203 3.364,3.429 0.420,0.225 10 E1 2.944,2.811 3.364,3.037 0.420,0.225 10 E1 2.944,2.405 3.364,2.630 0.420,0.225 10 E1 2.951,1.992 3.371,2.217 0.420,0.225 10 E1 2.944,1.438 3.364,1.663 0.420,0.225 10 E2 1.803,3.631 2.223,3.856 0.420,0.225 10 SWIL 1.221,3.161 1.641,3.387 0.420,0.225 10 GND 1.768,3.217 2.188,3.443 0.420,0.225 10 INDW 1.81,2.811 2.230,3.037 0.420,0.225 10 INDS 1.88,2.405 2.300,2.630 0.420,0.225 10 SS2 1.894,1.999 2.314,2.224 0.420,0.225 10 SS1 4.286,1.102 4.705,1.327 0.420,0.225 10 E1 4.286,2.116 4.705,2.342 0.420,0.225 10 E1 4.286,2.958 4.705,3.184 0.420,0.225 10 E2 4.274,5.603 4.693,5.829 0.420,0.225 10 E4 5.071,2.391 5.866,2.616 0.795,0.225 10 IG1 NO. 3 5.232,1.376 5.707,1.602 0.475,0.225 10 ACC 5.557,7.674 5.977,7.900 0.420,0.225 10 L 4.955,7.674 5.375,7.900 0.420,0.225 10 B 1.796,6.765 2.216,6.990 0.420,0.225 10 TACH 1.754,6.261 2.174,6.486 0.420,0.225 10 STSW 1.768,5.736 2.188,5.961 0.420,0.225 10 ACCR 1.985,4.684 2.280,4.910 0.295,0.225 10 +S 5.134,5.865 5.734,6.091 0.600,0.225 10 ST CUT 5.615,3.486 6.035,3.711 0.420,0.225 10 IG2 6.065,4.217 6.364,4.401 0.299,0.184 10 IGN 1.21,4.037 2.241,4.262 1.031,0.225 10 Engine Switch 0.922,5.121 2.175,5.284 1.253,0.164 10 Combination Meter 1.502,6.989 1.921,7.215 0.420,0.225 10 ECM 4.739,8.041 5.920,8.401 1.182,0.360 10 Park/Neutral Position Switch*5 2.994,6.59 3.275,6.815 0.281,0.225 10 8 2.994,6.086 3.275,6.311 0.281,0.225 10 4 2.994,5.575 3.275,5.800 0.281,0.225 10 3 0.997,3.063 1.278,3.289 0.281,0.225 10 5 2.244,3.54 2.525,3.765 0.281,0.225 10 11 2.244,3.119 2.525,3.345 0.281,0.225 10 13 2.244,2.727 2.525,2.952 0.281,0.225 10 12 2.244,2.321 2.525,2.546 0.281,0.225 10 2 2.244,1.922 2.525,2.147 0.281,0.225 10 7 2.994,4.509 3.275,4.734 0.281,0.225 10 9 2.954,3.456 3.235,3.681 0.281,0.225 10 25 2.954,3.035 3.235,3.261 0.281,0.225 10 14 2.954,2.636 3.235,2.861 0.281,0.225 10 15 2.954,2.23 3.235,2.455 0.281,0.225 10 16 2.954,1.816 3.235,2.042 0.281,0.225 10 17 2.994,1.27 3.275,1.495 0.281,0.225 10 1 2.994,0.689 3.275,0.914 0.281,0.225 10 6 5.739,7.602 6.020,7.828 0.281,0.225 10 5 4.332,6.048 4.613,6.273 0.281,0.225 10 8 6.204,3.474 6.485,3.700 0.281,0.225 10 8 4.919,2.769 5.200,2.995 0.281,0.225 10 6 6.202,2.775 6.483,3.000 0.281,0.225 10 7 4.918,3.491 5.199,3.716 0.281,0.225 10 1 4.868,3.292 5.149,3.517 0.281,0.225 10 1C 4.868,2.956 5.149,3.182 0.281,0.225 10 1B 6.155,2.956 6.436,3.182 0.281,0.225 10 1B 6.155,3.294 6.436,3.519 0.281,0.225 10 1B 5.008,5.523 5.289,5.749 0.281,0.225 10 5 5.673,5.529 5.954,5.755 0.281,0.225 10 3 5.663,5.333 5.944,5.558 0.281,0.225 10 1 5.008,5.327 5.289,5.552 0.281,0.225 10 2 4.78,7.595 5.061,7.821 0.281,0.225 10 4 4.297,0.934 4.578,1.159 0.281,0.225 10 22 4.336,1.948 4.617,2.173 0.281,0.225 10 3 4.297,2.79 4.578,3.016 0.281,0.225 10 11 4.336,5.424 4.617,5.649 0.281,0.225 10 6 2.263,4.594 2.544,4.819 0.281,0.225 10 4 1.2,6.549 1.620,6.774 0.420,0.225 10 STAR 1.21,3.883 1.630,4.108 0.420,0.225 10 E18 4.739,7.883 5.038,8.108 0.299,0.225 10 C24 4.91,6.816 5.789,7.141 0.879,0.324 10 Clutch Start Switch*4 5.739,6.407 6.020,6.632 0.281,0.225 10 2 4.78,6.4 5.061,6.625 0.281,0.225 10 1 4.91,6.676 5.209,6.826 0.299,0.151 10 e1 0.829,6.54 1.249,6.765 0.420,0.225 10 C46 2.272,6.751 2.692,6.976 0.420,0.225 10 A52 2.272,6.261 2.692,6.486 0.420,0.225 10 A52 2.272,5.736 2.692,5.961 0.420,0.225 10 A52 0.794,6.072 1.169,6.219 0.374,0.147 10 16*1 0.332,7.474 1.876,7.617 1.545,0.144 10 *1: for 1UR-FE, 1GR-FE 0.332,8.243 1.446,8.387 1.114,0.144 10 *4: for M/T 0.332,8.5 1.446,8.643 1.114,0.144 10 *5: for A/T 0.332,7.73 2.050,7.874 1.718,0.144 10 *2: for 1VD-FTV w/o DPF 0.332,7.987 1.911,8.130 1.579,0.144 10 *3: for 1VD-FTV w/ DPF 2.305,6.576 2.586,6.801 0.281,0.225 10 15 2.235,5.941 2.801,6.110 0.566,0.170 10 14*1, *2 2.245,5.209 2.572,5.388 0.328,0.179 10 41*1 5.156,3.413 5.575,3.747 0.420,0.334 10 IG2 MAIN 5.069,3.836 6.378,4.062 1.309,0.225 10 Integration Relay 2.945,8.205 4.490,8.542 1.545,0.337 10 Main Body ECU (Cowl Side Junction Block RH) 0.801,6.222 1.133,6.382 0.332,0.161 10 51*2 0.801,6.376 1.133,6.536 0.332,0.161 10 52*3 2.244,5.382 2.567,5.552 0.323,0.170 10 13*2 2.244,5.55 2.567,5.720 0.323,0.170 10 22*3 2.244,6.082 2.567,6.252 0.323,0.170 10 47*3

U163043E01
0.939,1.783 2.423,2.158 1.485,0.376 10 Shift Lock Control ECU (for A/T) 1.541,3.597 2.656,3.815 1.114,0.218 10 Stop Light Switch 3.056,6.726 4.601,7.090 1.545,0.364 10 Main Body ECU (Cowl Side Junction Block LH) 4.857,6.834 6.462,7.272 1.605,0.437 10 Certification ECU (Smart Key ECU Assembly) 5.072,3.52 6.380,3.815 1.309,0.295 10 Steering Lock ECU 2.854,1.313 3.246,1.525 0.392,0.211 10 E4 4.943,1.565 5.196,1.777 0.253,0.211 10 ST 2.907,1.124 3.174,1.433 0.267,0.309 10 2 3.18,4.374 3.600,4.628 0.420,0.253 10 CANH 3.18,4.837 3.600,5.090 0.420,0.253 10 CANL 3.18,5.726 3.600,5.980 0.420,0.253 10 CANN 3.18,5.278 3.600,5.531 0.420,0.253 10 CANP 3.18,6.182 3.600,6.435 0.420,0.253 10 GND2 2.856,4.364 3.144,4.568 0.288,0.205 10 E3 2.856,5.723 3.144,5.927 0.288,0.205 10 E3 2.856,5.268 3.144,5.472 0.288,0.205 10 E3 2.856,4.833 3.144,5.038 0.288,0.205 10 E3 2.854,6.17 3.141,6.375 0.288,0.205 10 2D 2.875,5.979 3.212,6.169 0.336,0.191 10 62 2.875,5.541 3.212,5.731 0.336,0.191 10 15 2.875,5.082 3.212,5.273 0.336,0.191 10 16 2.907,4.644 3.244,4.835 0.336,0.191 10 6 2.907,4.182 3.244,4.372 0.336,0.191 10 5 3.18,1.306 3.447,1.615 0.267,0.309 10 P 0.462,5.015 1.785,5.429 1.323,0.414 10 CAN Communication Line 3.18,3.17 3.600,3.423 0.420,0.253 10 STP 2.855,3.173 3.142,3.378 0.288,0.205 10 2B 2.867,2.977 3.204,3.168 0.336,0.191 10 22 4.193,6.346 4.480,6.551 0.288,0.205 10 2D 4.208,6.161 4.544,6.351 0.336,0.191 10 20 4.21,2.844 4.498,3.048 0.288,0.205 10 E1 4.2,2.658 4.536,2.849 0.336,0.191 10 19 4.21,2.381 4.498,2.586 0.288,0.205 10 E1 4.2,2.196 4.536,2.386 0.336,0.191 10 18 5.191,6.35 5.451,6.603 0.260,0.253 10 LIN 5.233,2.847 5.653,3.100 0.420,0.253 10 IGE 5.226,2.392 5.646,2.645 0.420,0.253 10 SLP1 5.247,3.071 5.667,3.325 0.420,0.253 10 LIN 5.709,2.69 6.129,2.943 0.420,0.253 10 SGND 5.862,2.344 6.129,2.597 0.267,0.253 10 IG2 5.807,3.033 6.227,3.286 0.420,0.253 10 GND 5.8,4.571 6.185,4.747 0.385,0.177 10 GND 5.226,4.571 5.646,4.824 0.420,0.253 10 LIN1 5.023,2.767 5.359,2.957 0.336,0.191 10 3 5.023,2.304 5.359,2.495 0.336,0.191 10 4 6.201,2.932 6.537,3.123 0.336,0.191 10 1 6.215,2.602 6.551,2.793 0.336,0.191 10 2 6.207,2.259 6.543,2.449 0.336,0.191 10 6 5.037,4.487 5.373,4.677 0.336,0.191 10 3 6.214,4.49 6.550,4.681 0.336,0.191 10 8 6.04,6.257 6.376,6.447 0.336,0.191 10 17 5.849,6.35 5.977,6.603 0.128,0.253 10 E 5.023,2.977 5.359,3.168 0.336,0.191 10 5 1.604,3.085 1.941,3.276 0.336,0.191 10 2 2.291,3.089 2.627,3.280 0.336,0.191 10 1 0.266,3.066 0.867,3.470 0.600,0.405 10 from Battery 4.929,5.068 6.520,5.469 1.591,0.401 10 ID Code Box (Immobiliser Code ECU) 3.768,6.35 4.188,6.603 0.420,0.253 10 LIN1 3.692,2.847 4.112,3.100 0.420,0.253 10 SLR+ 3.79,2.385 4.210,2.638 0.420,0.253 10 SLP 1.045,3.314 1.460,3.534 0.415,0.221 10 STOP 1.541,3.441 1.957,3.661 0.415,0.221 10 A30 4.859,6.682 5.147,6.886 0.288,0.205 10 E29 4.943,6.256 5.280,6.447 0.336,0.191 10 10 4.929,4.9 5.349,5.153 0.420,0.253 10 E28 5.072,3.366 5.492,3.619 0.420,0.253 10 E26 5.318,0.998 5.585,1.307 0.267,0.309 10 3 4.656,0.998 4.923,1.307 0.267,0.309 10 5 4.26,1.185 4.860,1.336 0.600,0.151 10 1*1, 2*2 5.332,1.191 5.922,1.346 0.590,0.155 10 2*1, 1*2 1.149,1.32 1.569,1.573 0.420,0.253 10 E 1.891,1.32 2.436,1.573 0.545,0.253 10 P2 0.967,1.222 1.303,1.413 0.336,0.191 10 3 2.144,1.212 2.480,1.402 0.336,0.191 10 11 0.939,1.631 1.354,1.851 0.415,0.221 10 E51 0.168,6.432 2.194,6.768 2.026,0.336 10 *1: except GRJ200L-GNANKC, URJ202L-GNTEKC 0.168,7.095 1.935,7.431 1.767,0.336 10 *2: for GRJ200L-GNANKC, URJ202L-GNTEKC

PROCEDURE

1.CHECK ENGINE SWITCH (SWITCH CONDITION)
a.

Check the power source mode change.

i.

When the key is inside the vehicle and the shift lever is in P (for A/T), check that pressing the engine switch causes the power source mode to change as follows:

OK:

off → on (ACC) → on (IG) → off





OK

2.CHECK WHETHER DTC OUTPUT RECURS

NG

GO TO ENTRY AND START SYSTEM (FOR START FUNCTION) (POWER SOURCE MODE DOES NOT CHANGE)

2.CHECK WHETHER DTC OUTPUT RECURS

b.

Check whether the trouble recurs 5 seconds after the engine switch is turned on (IG).


c.

Check whether DTCs for the main body ECU or certification ECU (smart key ECU assembly) are output.

Result
Result Proceed to
No DTC output A
Main body ECU
Entry and start system (for start function)
B
Certification ECU (Smart key ECU assembly)
Steering lock system
C
Certification ECU (Smart key ECU assembly)
Engine immobiliser system
D



A

3.CHECK CRANKING FUNCTION

B

GO TO ENTRY AND START SYSTEM (FOR START FUNCTION) (DIAGNOSTIC TROUBLE CODE CHART)

C

GO TO STEERING LOCK SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

D

3.CHECK CRANKING FUNCTION
a.

Check the engine cranking function.

i.

for A/T:

When there is fuel in the fuel tank, the key is inside the vehicle and the shift lever is in P, check that depressing the brake pedal and pressing the engine switch cranks the engine.

for M/T:

When there is fuel in the fuel tank and the key is inside the vehicle, check that depressing the clutch pedal and pressing the engine switch cranks the engine.

OK:

Engine cranks.





OK

4.READ VALUE USING INTELLIGENT TESTER (L CODE)

NG

8.READ VALUE USING INTELLIGENT TESTER (PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH)
4.READ VALUE USING INTELLIGENT TESTER (L CODE)
a.

Use the Data List to check if L code certification is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
L Code Check L code certification result/NG or OK OK: L code certification result is normal
NG: L code certification result is abnormal
-

OK:

OK is displayed on the intelligent tester.




OK

5.READ VALUE USING INTELLIGENT TESTER (ENGINE START CONDITION)

NG

23.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
5.READ VALUE USING INTELLIGENT TESTER (ENGINE START CONDITION)
a.

Use the Data List to check if the engine start is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Start Condition Engine start condition by certification ECU (smart key ECU assembly)/OK or NG OK: Engine start is permitted
NG: Engine start is prohibited
-

OK:

OK is displayed on the intelligent tester.




OK

6.READ VALUE USING INTELLIGENT TESTER (S CODE)

NG

24.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
6.READ VALUE USING INTELLIGENT TESTER (S CODE)
a.

Use the Data List to check if S code certification is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
S Code Check S code certification result/NG or OK OK: S code certification result is normal
NG: S code certification result is abnormal
-

OK:

OK is displayed on the intelligent tester.




OK

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

24.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU).


b.

Register the recognition code (ECU code).


c.

Check that the engine starts.

Result
Result Proceed to
Engine starts A
Engine does not start (for 1GR-FE) B
Engine does not start (for 1UR-FE) C
Engine does not start (for 3UR-FE) D
Engine does not start (for 1VD-FTV) E



A

END

B

C

D

E

8.READ VALUE USING INTELLIGENT TESTER (PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH)
a.

Use the Data List to check if the park/neutral position switch (for A/T) or clutch start switch (for M/T) is functioning properly.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Park/neutral position switch (A/T), clutch start switch (M/T)/ON or OFF ON: Shift lever in P or N (A/T), clutch pedal depressed (M/T)
OFF: Shift lever not in P or N (A/T), clutch pedal released (M/T)
-

Result
Result Proceed to
for A/T:
ON (shift lever in P or N) and OFF (shift lever not in P or N) displayed on the intelligent tester.
A
for M/T:
ON (clutch pedal depressed) and OFF (clutch pedal released) displayed on the intelligent tester.
B
for A/T:
ON (shift lever in P or N) and OFF (shift lever not in P or N) not displayed on the intelligent tester.
for M/T:
ON (clutch pedal depressed) and OFF (clutch pedal released) not displayed on the intelligent tester.
C



A

9.READ VALUE USING INTELLIGENT TESTER (SHIFT LOCK CONTROL ECU)

B

11.CHECK STEERING LOCK

C

15.INSPECT STARTER RELAY (ST)
9.READ VALUE USING INTELLIGENT TESTER (SHIFT LOCK CONTROL ECU)
a.

Use the Data List to check if the shift position signal is functioning properly.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift P Signal Shift P position signal/ON or OFF ON: Shift lever in P
OFF: Shift lever not in P
-

OK:

ON (shift lever in P) and OFF (shift lever not in P) are displayed on the intelligent tester.




OK

10.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)

NG

13.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SHIFT LOCK CONTROL ECU AND BODY GROUND)
10.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Use the Data List to check if the stop light switch is functioning properly.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch/ON or OFF ON: Brake pedal is depressed
OFF: Brake pedal is released
-

OK:

ON (brake pedal is depressed) and OFF (brake pedal is released) are displayed on the intelligent tester.




OK

11.CHECK STEERING LOCK

NG

20.INSPECT FUSE (STOP)
11.CHECK STEERING LOCK
a.

Check if the steering lock is released when turning the engine switch on (ACC).

OK:

The steering lock is released.




OK

12.CHECK MAIN BODY ECU

NG

GO TO STEERING LOCK SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

12.CHECK MAIN BODY ECU
U164592E01
0.464,1.935 0.839,2.168 0.375,0.233 10 E4 0.238,0.2 2.646,0.567 2.409,0.367 10 Component with harness connected: (Main Body ECU) 2.303,2.89 2.795,3.092 0.492,0.202 10 STSW 2.253,3.002 2.147,3.002 2.147,3.002 1.81,2.198 false

a.

Measure the voltage according to the value(s) in the table below.

HINT:

The voltage is generated at terminal STSW for 0.3 seconds when the engine cranks.


Standard Voltage:
Tester Connection Condition Specified Condition
E4-4 (STSW) - Body ground for A/T:
Brake pedal depressed, engine switch depressed
for M/T:
Clutch pedal depressed, engine switch depressed
11 to 14 V


Result
Result Proceed to
Outside specified range A
Within specified range (for 1GR-FE) B
Within specified range (for 1UR-FE) C
Within specified range (for 3UR-FE) D
Within specified range (for 1VD-FTV) E



A

REPLACE MAIN BODY ECU

B

C

D

E

13.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SHIFT LOCK CONTROL ECU AND BODY GROUND)
U164591E01
1.692,0.777 2.067,1.010 0.375,0.233 10 E4 5.061,0.779 5.436,1.012 0.375,0.233 10 E51 0.598,0.062 3.006,0.429 2.408,0.367 10 Front view of wire harness connector: (to Main Body ECU) 3.973,0.062 6.382,0.429 2.408,0.367 10 Front view of wire harness connector: (to Shift Lock Control ECU) 6.042,2.126 6.304,2.328 0.263,0.202 10 P2 2.401,1.161 2.578,1.363 0.177,0.202 10 P 4.199,1.146 4.358,1.348 0.158,0.202 10 E 4.348,1.237 4.435,1.237 4.435,1.237 5.089,1.603 false 5.978,2.224 5.891,2.224 5.891,2.224 5.385,1.94 false 2.354,1.257 2.267,1.257 2.267,1.257 1.862,1.484 false

a.

Disconnect the E4 main body ECU connector.


b.

Disconnect the E51 shift lock control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E4-2 (P) - E51-11 (P2) Always Below 1 Ω
E51-3 (E) - Body ground Always Below 1 Ω
E4-2 (P) or E51-11 (P2) - Body ground Always 10 kΩ or higher




OK

14.INSPECT SHIFT LOCK CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT SHIFT LOCK CONTROL ECU
a.
U164593E01
0.221,0.217 2.558,0.562 2.336,0.345 10 Component with harness connected: (Shift Lock Control ECU) 2.82,1.421 3.050,1.623 0.230,0.202 10 E 0.413,2.833 0.643,3.035 0.230,0.202 10 P2 0.7,2.955 0.807,2.955 0.807,2.955 1.46,2.444 false 2.744,1.531 2.638,1.531 2.638,1.531 1.809,2.042 false 1.568,1.18 1.878,1.319 0.310,0.139 10 E51

C165581E01
2.909,2.182 3.322,2.383 0.413,0.201 10 GND

Check the signal waveform according to the condition(s) in the table below.

Reference
Terminal No. (Symbol) Tool Setting Condition
E51-11 (P2) - E51-3 (E) 2 V/DIV., 20 msec./DIV. Shift lever in P

OK:

The waveform is similar to that shown in the illustration.


Result
Result Proceed to
OK A
NG for 1GR-FE B
for 1VD-FTV, 3UR-FE, 1UR-FE C



A

REPLACE MAIN BODY ECU

B

C

15.INSPECT STARTER RELAY (ST)
a.
A111813E01
2.851,0.206 3.006,0.376 0.156,0.170 10 1 1.321,1.183 1.477,1.353 0.156,0.170 10 1 1.699,0.974 1.855,1.144 0.156,0.170 10 3 0.37,0.786 0.526,0.955 0.156,0.170 10 3 2.428,1.766 2.584,1.936 0.156,0.170 10 2 0.36,1.182 0.516,1.351 0.156,0.170 10 2 3.206,0.968 3.362,1.138 0.156,0.170 10 5 1.315,0.773 1.471,0.943 0.156,0.170 10 5 2.444,0.695 2.787,0.321 false 2.856,1.054 3.177,1.054 false 2.085,1.054 1.836,1.054 false 2.49,1.413 2.49,1.766 false

expect GRJ200L-GNANKC, URJ202L-GNTEKC:

i.

Remove the ST relay from the engine room relay block.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied to terminals 1 and 2 Below 1 Ω




b.
C357863E01
2.021,0.719 1.583,0.323 true 2.604,0.76 2.906,0.302 true 2.5,1.104 2.906,1.104 true 2.5,1.594 2.906,1.594 true 1.458,0.177 1.615,0.375 0.156,0.198 10 false 1 2.938,0.167 3.094,0.365 0.156,0.198 10 false 2 2.958,1.021 3.115,1.219 0.156,0.198 10 false 5 2.948,1.51 3.104,1.708 0.156,0.198 10 false 3 0.25,0.75 0.406,0.948 0.156,0.198 10 false 5 1.177,0.75 1.333,0.948 0.156,0.198 10 false 3 0.26,1.281 0.417,1.479 0.156,0.198 10 false 1 1.177,1.281 1.333,1.479 0.156,0.198 10 false 2

for GRJ200L-GNANKC, URJ202L-GNTEKC:

i.

Remove the ST relay from the engine room relay block.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied to terminals 1 and 2 Below 1 Ω


Result
Result Proceed to
Within specified range (for A/T) A
Within specified range (for M/T) B
Outside specified range C




A

16.INSPECT PARK/NEUTRAL POSITION SWITCH

B

17.INSPECT CLUTCH START SWITCH

C

REPLACE STARTER RELAY

16.INSPECT PARK/NEUTRAL POSITION SWITCH
a.
B138018E30
0.667,1.417 0.802,1.417 0.802,1.417 1.135,1.698 false 2.865,2.448 2.625,2.448 2.625,2.448 2.281,2.156 false 0.125,0.115 2.604,0.479 2.479,0.365 10 false Component without harness connected: (Park/Neutral Position Switch) 0.5,1.333 0.708,1.563 0.208,0.229 10 false B 2.917,2.354 3.125,2.583 0.208,0.229 10 false L

Disconnect the C24 park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) P Below 1 Ω
4 (B) - 5 (L) N Below 1 Ω
4 (B) - 5 (L) Not in P or N 10 kΩ or higher


Result
Result Proceed to
Outside specified range (for A750F) A
Outside specified range (for AB60F) B
Within specified range C



A

B

C

18.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH AND BODY GROUND)
17.INSPECT CLUTCH START SWITCH
a.
A179589E03
0.192,0.045 2.704,0.445 2.512,0.400 10 Component without harness connected: (Clutch Start Switch) 1.885,2.665 2.452,2.845 0.568,0.180 10 Pushed 1.352,1.111 2.087,1.291 0.735,0.180 10 Switch Pin 2.81,2.665 3.313,2.977 0.503,0.312 10 Not Pushed 2.225,1.202 2.474,1.202 2.474,1.202 2.706,2.006 false

Disconnect the A49 (for LHD) or e1 (for RHD) clutch start switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Clutch start switch pin pushed Below 1 Ω
1 - 2 Clutch start switch pin not pushed 10 kΩ or higher




OK

18.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH AND BODY GROUND)

NG

REPLACE CLUTCH START SWITCH

18.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH AND BODY GROUND)
U163139E01
2.596,1.749 2.971,1.982 0.375,0.233 10 E1 5.971,1.217 6.346,1.450 0.375,0.233 10 C24 0.652,0.607 3.060,0.974 2.408,0.367 10 Front view of wire harness connector: (to Main Body ECU) 3.991,0 6.400,0.367 2.408,0.367 10 Front view of wire harness connector: (to Park/Neutral Position Switch) 5.626,2.992 6.075,3.226 0.449,0.233 10 A49*1 5.659,3.33 6.109,3.563 0.449,0.233 10 e1*2 3.991,2.041 6.400,2.408 2.409,0.367 10 Front view of wire harness connector: (to Clutch Start Switch) 0.528,2.123 0.872,2.325 0.344,0.202 10 STR 0.647,3.016 2.218,3.190 1.570,0.174 10 *1: for LHD 0.647,3.373 2.218,3.548 1.570,0.174 10 *2: for RHD 0.858,2.207 0.966,2.207 0.966,2.207 1.464,2.027 false 6.077,0.796 6.420,0.998 0.344,0.202 10 B 6.005,0.893 5.909,0.893 5.909,0.893 5.466,1.167 false

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for A/T):
Tester Connection Condition Specified Condition
E1-8 (STR) - C24-4 (B) Always Below 1 Ω
E1-8 (STR) or C24-4 (B) - Body ground Always 10 kΩ or higher


Standard Resistance (for M/T):
Tester Connection Condition Specified Condition
for LHD:
E1-8 (STR) - A49-1
Always Below 1 Ω
for LHD:
E1-8 (STR) or A49-1 - Body ground
Always 10 kΩ or higher
for RHD:
E1-8 (STR) - e1-1
Always Below 1 Ω
for RHD:
E1-8 (STR) or e1-1 - Body ground
Always 10 kΩ or higher




OK

19.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH - STARTER RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH - STARTER RELAY AND BODY GROUND)
U165452E01
0.531,0.07 3.119,0.424 2.588,0.353 10 Component without ST relay connected:(Engine Room Relay Block) 4.536,0.064 6.925,0.400 2.389,0.336 10 Front view of wire harness connector:(to Park/Neutral Position Switch) 3.827,2.475 4.301,2.664 0.474,0.190 10 ST*4 3.829,1.334 4.243,1.524 0.414,0.190 10 ST*3 0.192,2.986 1.030,3.182 0.839,0.196 10 *1: for LHD 0.213,3.325 1.088,3.499 0.874,0.174 10 *2: for RHD 4.456,1.898 6.861,2.243 2.406,0.345 10 Front view of wire harness connector:(to Clutch Start Switch) 6.198,1.16 6.569,1.338 0.371,0.178 10 C24 5.894,2.901 6.351,3.090 0.457,0.190 10 A49*1 5.95,3.255 6.407,3.445 0.457,0.190 10 e1*2 4.895,1.403 4.745,1.726 4.745,1.726 4.497,1.726 false 4.363,1.66 4.570,1.879 0.207,0.220 10 L 1.216,3.344 4.450,3.534 3.235,0.190 10 *4: except GRJ200L-GNANKC, URJ202L-GNTEKC 1.216,2.988 4.450,3.177 3.235,0.190 10 *3: for GRJ200L-GNANKC, URJ202L-GNTEKC

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for A/T):
Tester Connection Condition Specified Condition
C24-5 (L) - Relay block ST relay terminal 1*1
C24-5 (L) - Relay block ST relay terminal 2*2
Always Below 1 Ω
C24-5 (L) or Relay block ST relay terminal 1 - Body ground*1
C24-5 (L) or Relay block ST relay terminal 2 - Body ground*2
Always 10 kΩ or higher
Relay block ST relay terminal 2 - Body ground*1
Relay block ST relay terminal 1- Body ground*2
Always Below 1 Ω


HINT:
·

*1: for GRJ200L-GNANKC, URJ202L-GNTEKC

·

*2: except GRJ200L-GNANKC, URJ202L-GNTEKC



Standard Resistance (for M/T):
Tester Connection Condition Specified Condition
for LHD:
A49-2 - Relay block ST relay terminal 1*1
A49-2 - Relay block ST relay terminal 2*2
Always Below 1 Ω
for LHD:
A49-2 or Relay block ST relay terminal 1 - Body ground*1
A49-2 or Relay block ST relay terminal 2 - Body ground*2
Always 10 kΩ or higher
for RHD:
e1-2 - Relay block ST relay terminal 1*1
e1-2 - Relay block ST relay terminal 2*2
Always Below 1 Ω
for RHD:
e1-2 or Relay block ST relay terminal 1 - Body ground*1
e1-2 or Relay block ST relay terminal 2 - Body ground*2
Always 10 kΩ or higher
Relay block ST relay terminal 2 - Body ground*1
Relay block ST relay terminal 1 - Body ground*2
Always Below 1 Ω


HINT:
·

*1: for GRJ200L-GNANKC, URJ202L-GNTEKC

·

*2: except GRJ200L-GNANKC, URJ202L-GNTEKC





OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT FUSE (STOP)
a.

Remove the STOP fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
STOP fuse Always Below 1 Ω




OK

21.INSPECT STOP LIGHT SWITCH

NG

REPLACE FUSE

21.INSPECT STOP LIGHT SWITCH
A175403E01
0.074,0 2.652,0.399 2.578,0.399 10 Component without harness connected: (Stop Light Switch) 1.102,2.975 1.907,3.149 0.804,0.174 10 Not Pushed 0.95,2.493 1.422,2.263 1.422,2.263 1.627,2.263 false 1.102,2.569 1.661,2.743 0.559,0.174 10 Pushed 1.685,2.151 2.429,2.325 0.744,0.175 10 Switch Pin

a.

Disconnect the A30 stop light switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Stop light switch pin not pushed Below 1 Ω
3 - 4 Stop light switch pin pushed Below 1 Ω
1 - 2 Stop light switch pin pushed 10 kΩ or higher
3 - 4 Stop light switch pin not pushed 10 kΩ or higher




OK

22.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - STOP LIGHT SWITCH AND BODY GROUND)

NG

REPLACE STOP LIGHT SWITCH

22.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - STOP LIGHT SWITCH AND BODY GROUND)
U163029E01
2.184,0.832 2.559,1.065 0.375,0.233 10 2B 5.419,0.838 5.794,1.071 0.375,0.233 10 A30 1.038,0.064 3.446,0.432 2.408,0.367 10 Front view of wire harness connector: (to Main Body ECU) 4.228,0.064 6.637,0.432 2.408,0.367 10 Front view of wire harness connector: (to Stop Light Switch) 3.366,2.216 3.710,2.418 0.344,0.202 10 STP 3.304,2.312 3.217,2.312 3.217,2.312 2.817,1.935 false

a.

Disconnect the 2B main body ECU connector.


b.

Disconnect the A30 stop light switch connector.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-2 - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
2B-22 (STP) - A30-1 Always Below 1 Ω
2B-22 (STP) or A30-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
a.

Replace the steering lock actuator assembly (steering lock ECU).

HINT:



b.

Register the recognition code (ECU code).


c.

Check that the engine starts.

OK:

Engine starts.




OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

24.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly).


b.

Register the recognition code (ECU code).


c.

Check that the engine starts.

OK:

Engine starts.




OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)