Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052841 METER / GAUGE / DISPLAY _0255598 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.

DTC No. DTC Detection Condition Trouble Area
B1507 When IG voltage is 9.5 V or more and the following condition is detected:
·

Open in turn signal light circuit


·

LED

·

Bulb

·

Harness or connector

·

Outer rear view mirror assembly LH*3

·

Outer rear view mirror assembly RH*3

·

Outer mirror control ECU assembly LH*1*3

·

Outer mirror control ECU assembly RH*1*3

·

Rear combination light socket and wire subassembly LH*2

·

Rear combination light socket and wire subassembly RH*2

·

Towing Converter Assembly*4

·

Combination meter assembly


B1508 When IG voltage is 9.5 V or more and the following condition is detected:
·

Short in turn signal light circuit or hazard warning light circuit


·

LED

·

Bulb

·

Harness or connector

·

Outer rear view mirror assembly LH*3

·

Outer rear view mirror assembly RH*3

·

Outer mirror control ECU assembly LH*1*3

·

Outer mirror control ECU assembly RH*1*3

·

Rear combination light socket and wire subassembly LH*2

·

Rear combination light socket and wire subassembly RH*2

·

Towing Converter Assembly*4

·

Combination meter assembly



*1: w/ Retract Mirror

*2: except Double Swing Out Type

*3: for Outer Rear View Mirror

*4: w/ Towing Package


WIRING DIAGRAM

RH Side


E339203E03
6.01,7.26 6.385,7.427 0.375,0.167 10 false E120 5.979,7.448 7.146,7.792 1.167,0.344 10 false Combination Meter Assembly 2.781,7.625 3.135,7.792 0.354,0.167 10 false K64 2.781,7.771 4.115,8.01 1.333,0.24 10 false Towing Converter*6 3.771,7.302 4.146,7.458 0.375,0.156 10 false RTIN 4.198,7.219 4.365,7.375 0.167,0.156 10 false 3 4,5.365 4.146,5.531 0.146,0.167 10 false E 4.188,5.365 4.344,5.531 0.156,0.167 10 false 2 4,5.115 4.156,5.281 0.156,0.167 10 false B 4.188,5.115 4.344,5.281 0.156,0.167 10 false 1 0.135,7.042 0.781,7.208 0.646,0.167 10 false L4*3,Y1*4 0.135,7.198 2.396,7.708 2.26,0.51 10 false Rear Combination Light Socket and Wire Sub-assembly RH*3 or Rear Combination Light Assembly RH*4 2.208,2.313 2.458,2.479 0.25,0.167 10 false E1 2.49,2.333 2.698,2.5 0.208,0.167 10 false 21 2.01,1.958 2.438,2.125 0.427,0.167 10 false TRNR 2.49,1.948 2.646,2.115 0.156,0.167 10 false 4 1.365,2.708 1.604,2.875 0.24,0.167 10 false I32 1.365,2.906 2.656,3.385 1.292,0.479 10 false Outer Rear View Mirror Assembly RH*1, *7 2.406,0.708 2.552,0.875 0.146,0.167 10 false E 2.604,0.719 2.76,0.885 0.156,0.167 10 false 4 2.406,0.375 2.542,0.542 0.135,0.167 10 false B 2.594,0.354 2.75,0.521 0.156,0.167 10 false 5 0.125,1.125 0.417,1.292 0.292,0.167 10 false A69 0.135,1.292 2.948,1.635 2.813,0.344 10 false Headlight Assembly RH 3.229,2.792 4.521,3.313 1.292,0.521 10 false Outer Mirror Control ECU Assembly RH*1, *7 3.292,2.323 3.688,2.49 0.396,0.167 10 false RE1 2.969,2.26 3.156,2.427 0.188,0.167 10 false 14 3.26,1.938 3.667,2.104 0.406,0.167 10 false TRN+ 4.042,2.333 4.438,2.5 0.396,0.167 10 false GND 4.01,1.948 4.417,2.115 0.406,0.167 10 false TRNI 2.979,1.865 3.167,2.031 0.188,0.167 10 false 16 2.948,2.438 3.177,2.625 0.229,0.188 10 false I37 2.948,2.052 3.177,2.24 0.229,0.188 10 false I37 4.594,2.25 4.781,2.417 0.188,0.167 10 false 7 4.552,1.844 4.74,2.01 0.188,0.167 10 false 11 4.531,2.448 4.76,2.635 0.229,0.188 10 false I38 4.531,2.031 4.76,2.219 0.229,0.188 10 false I38 6.146,0.448 6.365,0.615 0.219,0.167 10 false LR 5.938,0.354 6.125,0.521 0.188,0.167 10 false 13 0.073,8.094 1.51,8.375 1.438,0.281 10 false *1: w/ Retract Mirror 0.073,8.396 1.51,8.677 1.438,0.281 10 false *2: w/o Retract Mirror 1.542,8.094 3.708,8.375 2.167,0.281 10 false *3: except Double Swing Out Type 1.542,8.396 3.469,8.677 1.927,0.281 10 false *4: for Double Swing Out Type 3.771,8.094 5.083,8.375 1.313,0.281 10 false *5: for Front Fender 5.177,8.094 7.063,8.375 1.885,0.281 10 false *7: for Outer Rear View Mirror 3.771,8.396 5.26,8.677 1.49,0.281 10 false *6: w/ Towing Package 0.063,2.74 1.167,3.24 1.104,0.5 10 false Side Turn Signal Light Assembly RH*1*7 2.125,4.104 2.469,4.271 0.344,0.167 10 false GND 2.49,4.104 2.698,4.271 0.208,0.167 10 false 21 2.01,3.719 2.438,3.885 0.427,0.167 10 false TRNL 2.49,3.74 2.646,3.906 0.156,0.167 10 false 4 1.375,4.521 1.615,4.688 0.24,0.167 10 false I20 1.365,4.688 2.656,5.198 1.292,0.51 10 false Outer Rear View Mirror Assembly RH*2, *7 0.094,4.594 1.198,5.104 1.104,0.51 10 false Side Turn Signal Light Assembly RH*2, *7 2.792,5.76 3.083,5.927 0.292,0.167 10 false A47 2.781,5.917 5.385,6.115 2.604,0.198 10 false Side Turn Signal Light Assembly RH 1.635,6.635 1.781,6.802 0.146,0.167 10 false E 1.823,6.656 2.354,6.823 0.531,0.167 10 false 3*3,4*6 1.427,6.406 1.781,6.573 0.354,0.167 10 false TRN 1.823,6.406 2.344,6.573 0.521,0.167 10 false 4*3,1*4 4.948,1.938 5.26,2.104 0.313,0.167 10 false *1*7 4.948,2.302 5.26,2.469 0.313,0.167 10 false *1*7 4.552,3.719 4.885,3.885 0.333,0.167 10 false *2*7 4.552,4.104 4.885,4.271 0.333,0.167 10 false *2*7 4.49,5.115 4.646,5.281 0.156,0.167 10 false *5 4.49,5.375 4.646,5.542 0.156,0.167 10 false *5 4.49,7.208 4.646,7.375 0.156,0.167 10 false *6


LH Side


E339203E04
6.01,7.26 6.385,7.427 0.375,0.167 10 false E120 5.979,7.417 7.146,7.76 1.167,0.344 10 false Combination Meter Assembly 2.781,7.604 3.26,7.771 0.479,0.167 10 false K64 2.781,7.76 4.083,7.958 1.302,0.198 10 false Towing Converter*6 3.813,7.302 4.146,7.458 0.333,0.156 10 false LTIN 4.198,7.219 4.365,7.375 0.167,0.156 10 false 9 4,5.375 4.146,5.542 0.146,0.167 10 false E 4.188,5.365 4.344,5.531 0.156,0.167 10 false 2 4,5.115 4.156,5.281 0.156,0.167 10 false B 4.188,5.115 4.344,5.281 0.156,0.167 10 false 1 0.135,7.052 0.781,7.219 0.646,0.167 10 false K4*3,n1*4 0.135,7.24 2.396,7.75 2.26,0.51 10 false Rear Combination Light Socket and Wire Sub-assembly RH*3 or Rear Combination Light Assembly LH*4 2.219,2.313 2.469,2.479 0.25,0.167 10 false E1 2.5,2.323 2.708,2.49 0.208,0.167 10 false 21 2.01,1.969 2.438,2.135 0.427,0.167 10 false TRNL 2.49,1.948 2.646,2.115 0.156,0.167 10 false 4 1.365,2.719 1.604,2.885 0.24,0.167 10 false I35 1.365,2.875 2.479,3.417 1.115,0.542 10 false Outer Rear View Mirror Assembly LH*1, *7 2.406,0.729 2.552,0.896 0.146,0.167 10 false E 2.583,0.729 2.74,0.896 0.156,0.167 10 false 4 2.427,0.365 2.563,0.531 0.135,0.167 10 false B 2.594,0.354 2.75,0.521 0.156,0.167 10 false 5 0.135,1.135 0.427,1.302 0.292,0.167 10 false A66 0.135,1.323 2.948,1.667 2.813,0.344 10 false Headlight Assembly LH 3.229,2.76 4.521,3.26 1.292,0.5 10 false Outer Mirror Control ECU Assembly LH*1, *7 3.292,2.323 3.688,2.49 0.396,0.167 10 false LE1 2.969,2.24 3.156,2.406 0.188,0.167 10 false 14 3.26,1.969 3.667,2.135 0.406,0.167 10 false TRN+ 4.042,2.323 4.438,2.49 0.396,0.167 10 false GND 4.01,1.979 4.417,2.146 0.406,0.167 10 false TRNI 2.979,1.854 3.167,2.021 0.188,0.167 10 false 16 2.948,2.448 3.177,2.635 0.229,0.188 10 false I40 2.948,2.042 3.177,2.229 0.229,0.188 10 false I40 4.594,2.24 4.781,2.406 0.188,0.167 10 false 7 4.552,1.844 4.74,2.01 0.188,0.167 10 false 11 4.531,2.448 4.76,2.635 0.229,0.188 10 false I41 4.531,2.042 4.76,2.229 0.229,0.188 10 false I41 6.146,0.458 6.365,0.625 0.219,0.167 10 false LL 5.99,0.365 6.177,0.531 0.188,0.167 10 false 7 0.146,8.094 1.583,8.375 1.438,0.281 10 false *1: w/ Retract Mirror 0.146,8.396 1.583,8.677 1.438,0.281 10 false *2: w/o Retract Mirror 1.615,8.094 3.781,8.375 2.167,0.281 10 false *3: except Double Swing Out Type 1.615,8.396 3.542,8.677 1.927,0.281 10 false *4: for Double Swing Out Type 3.844,8.094 5.135,8.375 1.292,0.281 10 false *5: for Front Fender 5.167,8.094 7.073,8.375 1.906,0.281 10 false *7: for Outer Rear View Mirror 3.844,8.396 5.771,8.677 1.927,0.281 10 false *6: w/ Towing Package 0.073,2.771 1.167,3.302 1.094,0.531 10 false Side Turn Signal Light Assembly LH*1, *7 2.125,4.104 2.469,4.271 0.344,0.167 10 false GND 2.49,4.115 2.698,4.281 0.208,0.167 10 false 21 2.01,3.74 2.438,3.906 0.427,0.167 10 false TRNL 2.49,3.75 2.646,3.917 0.156,0.167 10 false 4 1.365,4.5 1.604,4.667 0.24,0.167 10 false I21 1.365,4.698 2.656,5.229 1.292,0.531 10 false Outer Rear View Mirror Assembly LH*2, *7 0.073,4.583 1.313,5.104 1.24,0.521 10 false Side Turn Signal Light Assembly LH*2, *7 2.792,5.76 3.083,5.927 0.292,0.167 10 false A45 2.792,5.958 5.396,6.156 2.604,0.198 10 false Side Turn Signal Light Assembly LH*5 1.635,6.635 1.781,6.802 0.146,0.167 10 false E 1.823,6.667 2.354,6.833 0.531,0.167 10 false 3*3,4*4 1.427,6.396 1.781,6.563 0.354,0.167 10 false TRN 1.823,6.406 2.344,6.573 0.521,0.167 10 false 4*3,1*4 4.948,1.927 5.26,2.094 0.313,0.167 10 false *1*7 4.948,2.313 5.26,2.479 0.313,0.167 10 false *1*7 4.552,3.719 4.865,3.885 0.313,0.167 10 false *2*7 4.552,4.104 4.885,4.271 0.333,0.167 10 false *2*7 4.49,5.115 4.646,5.281 0.156,0.167 10 false *5 4.49,5.354 4.646,5.521 0.156,0.167 10 false *5 4.49,7.208 4.646,7.375 0.156,0.167 10 false *6


CAUTION / NOTICE / HINT

NOTICE:

Inspect the bulbs for this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.


b.

Recheck for DTCs and check that no DTCs are output.

Result
Result Proceed to
B1507 and B1508 are output A
B1507 and B1508 are not output B



A

2.INSPECT LIGHTS

B

2.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.

Result
Result Proceed to
RH side turn signal light does not illuminate A
LH side turn signal light does not illuminate B



A

3.CHECK HARNESS AND CONNECTOR (TURN SIGNAL CIRCUIT RH)

B

12.CHECK HARNESS AND CONNECTOR (TURN SIGNAL CIRCUIT LH)
3.CHECK HARNESS AND CONNECTOR (TURN SIGNAL CIRCUIT RH)

*1: w/ Retract Mirror

*2: w/o Retract Mirror

*3: except Double Swing Out Type

*4: for Double Swing Out Type

*5: for Front Fender

*6: w/ Towing Package

*7: for Outer Rear View Mirror


a.

Disconnect the E120 combination meter assembly connector.


b.

Disconnect the A69 headlight assembly RH connector.


c.

Disconnect the I20*2 or I32*1 outer rear view mirror assembly RH connector.*7


d.

Disconnect the A47 side turn signal light assembly RH connector.*5


e.

Disconnect the L4*3 or Y1*4 rear combination light assembly RH connector.


f.

Disconnect the K64 towing converter connector.*6


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A69-5 (B) - E120-13 (LR) Always Below 1 Ω
A69-4 (E) - Body ground Always Below 1 Ω
I20-4 (TRNL) - E120-13 (LR) Always Below 1 Ω
I20-21 (GND) - Body ground Always Below 1 Ω
I32-4 (TRNR) - E120-13 (LR) Always Below 1 Ω
I32-21 (E1) - Body ground Always Below 1 Ω
A47-1 (B) - E120-13 (LR) Always Below 1 Ω
A47-2 (E) - Body ground Always Below 1 Ω
L4-4 (TRN) - E120-13 (LR) Always Below 1 Ω
L4-3 (E) - Body ground Always Below 1 Ω
Y1-1 (TRN) - E120-13 (LR) Always Below 1 Ω
Y1-4 (E) - Body ground Always Below 1 Ω
K64-3 (RTIN) - E120-13 (LR) Always Below 1 Ω
E120-13 (LR) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK A
NG (for Outer Rear View Mirror with Retract Mirror) B
NG (except Outer Rear View Mirror with Retract Mirror) C



A

4.INSPECT HEADLIGHT ASSEMBLY RH

B

10.CHECK HARNESS AND CONNECTOR (TURN SIGNAL CIRCUIT RH)

C

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.INSPECT HEADLIGHT ASSEMBLY RH

b.
E339190E04
0.906,1.823 1.146,1.823 1.146,1.823 1.677,1.135 true 2.698,1.667 2.448,1.667 2.448,1.667 2.167,1.177 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.729,1.76 0.938,1.958 0.208,0.198 10 false B 2.76,1.583 2.948,1.813 0.188,0.229 10 false E

Apply battery voltage between the terminals and check the light illumination condition.

Text in Illustration
*a Component without harness connected
(Headlight Assembly RH)

OK:
Condition Specified Condition
Battery positive (+) →5 (B)
Battery positive (-) →4 (E)
Turn signal light illuminates


Result:
Result Proceed to
OK (for Outer Rear View Mirror) A
OK (for Front Fender) B
NG (for Halogen Headlight) C
NG (for LED Headlight) D
NG (for Halogen Headlight and LED Headlight) E




A

5.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

B

6.CHECK VEHICLE TYPE

C

D

E

5.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Remove the outer rear view mirror assembly RH.

(See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL)


b.

Inspect the outer rear view mirror assembly RH.

(See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION)



OK

6.CHECK VEHICLE TYPE

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

6.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
except Double Swing Out Type A
for Double Swing Out Type B



A

7.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH

B

8.CHECK VEHICLE TYPE
7.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH
a.

Remove the rear combination light socket and wire subassembly RH (see page Vehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL).


b.

Install the turn signal light bulb to the rear combination light socket and wire sub-assembly RH.


c.
C179946E05
2.125,1.635 2.469,1.635 false 1.854,1.552 1.854,0.573 1.854,0.573 1.948,0.573 false 0.052,0 0.583,0.281 0.531,0.281 10 false *a 2.521,1.563 3.052,1.844 0.531,0.281 10 false E 2.021,0.469 2.552,0.75 0.531,0.281 10 false TRN

Apply battery voltage between the terminals and check the light illumination condition.

Text in Illustration
*a Component without harness connected
(Rear Combination Light Socket and Wire Sub-assembly RH)

OK:
Condition Specified Condition
Battery positive (+) →4 (TRN)
Battery positive (-) →3 (E)
Turn signal light illuminates




OK

8.CHECK VEHICLE TYPE

NG

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH

8.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Towing Package A
w/o Towing Package B



A

9.CHECK TOWING CONVERTER

B

REPLACE COMBINATION METER ASSEMBLY

9.CHECK TOWING CONVERTER
a.

Replace the towing converter.


b.

Clear the DTCs.


c.

Check for DTCs and check that no DTCs are output.



OK

END (TOWING CONVERTER IS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (TURN SIGNAL CIRCUIT RH)

*1: except Double Swing Out Type

*2: for Double Swing Out Type

*3: w/ Towing Package


a.

Disconnect the E120 combination meter assembly connector.


b.

Disconnect the A69 headlight assembly RH connector.


c.

Disconnect the I38 outer mirror control ECU assembly RH connector.


d.

Disconnect the L4*1 or Y1*2 rear combination light assembly RH connector.


e.

Disconnect the K64 towing converter connector.*3


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A69-5 (B) - E120-13 (LR) Always Below 1 Ω
A69-4 (E) - Body ground Always Below 1 Ω
I38-11 (TRNI) - E120-13 (LR) Always Below 1 Ω
I38-7 (GND) - Body ground Always Below 1 Ω
L4-4 (TRN) - E120-13 (LR) Always Below 1 Ω
L4-3 (E) - Body ground Always Below 1 Ω
Y1-1 (TRN) - E120-13 (LR) Always Below 1 Ω
Y1-4 (E) - Body ground Always Below 1 Ω
K64-3 (RTIN) - E120-13 (LR) Always Below 1 Ω
E120-13 (LR) - Body ground Always 10 kΩ or higher




OK

11.CHECK HARNESS AND CONNECTOR (TURN SIGNAL CIRCUIT RH)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

11.CHECK HARNESS AND CONNECTOR (TURN SIGNAL CIRCUIT RH)
a.

Disconnect the I37 outer mirror control ECU assembly RH connector.


b.

Disconnect the I32 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I37-16 (TRN+) - I32-4 (TRNR) Always Below 1 Ω
I37-14 (RE1) - I32-21 (E1) Always Below 1 Ω
I37-16 (TRN+) or I32-4 (TRNR) - I37-14 (RE1) or I32-21 (E1) Always 10 kΩ or higher




OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

12.CHECK HARNESS AND CONNECTOR (TURN SIGNAL CIRCUIT LH)

*1: w/ Retract Mirror

*2: w/o Retract Mirror

*3: except Double Swing Out Type

*4: for Double Swing Out Type

*5: for Front Fender

*6: w/ Towing Package

*7: for Outer Rear View Mirror


a.

Disconnect the E120 combination meter assembly connector.


b.

Disconnect the A66 headlight assembly LH connector.


c.

Disconnect the I21*2 or I35*1 outer rear view mirror assembly LH connector.*7


d.

Disconnect the A45 side turn signal light assembly LH connector.*5


e.

Disconnect the K4*3 or n1*4 rear combination light assembly LH connector.


f.

Disconnect the K64 towing converter connector.*6


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-5 (B) - E120-7 (LL) Always Below 1 Ω
A66-4 (E) - Body ground Always Below 1 Ω
I21-4 (TRNL) - E120-7 (LL) Always Below 1 Ω
I21-21 (GND) - Body ground Always Below 1 Ω
I35-4 (TRNL) - E120-7 (LL) Always Below 1 Ω
I35-21 (E1) - Body ground Always Below 1 Ω
A45-1 (B) - E120-7 (LL) Always Below 1 Ω
A45-2 (E) - Body ground Always Below 1 Ω
K4-4 (TRN) - E120-7 (LL) Always Below 1 Ω
K4-3 (E) - Body ground Always Below 1 Ω
n1-1 (TRN) - E120-7 (LL) Always Below 1 Ω
n1-4 (E) - Body ground Always Below 1 Ω
K64-9 (LTIN) - E120-7 (LL) Always Below 1 Ω
E120-7 (LL) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK A
NG (for Outer Rear View Mirror with Retract Mirror) B
NG (except Outer Rear View Mirror with Retract Mirror) C



A

13.INSPECT HEADLIGHT ASSEMBLY LH

B

19.CHECK HARNESS AND CONNECTOR (TURN SIGNAL CIRCUIT LH)

C

REPAIR OR REPLACE HARNESS AND CONNECTOR

13.INSPECT HEADLIGHT ASSEMBLY LH

b.
E339190E04
0.906,1.823 1.146,1.823 1.146,1.823 1.677,1.135 true 2.698,1.667 2.448,1.667 2.448,1.667 2.167,1.177 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.729,1.76 0.938,1.958 0.208,0.198 10 false B 2.76,1.583 2.948,1.813 0.188,0.229 10 false E

Apply battery voltage between the terminals and check the light illumination condition.

Text in Illustration
*a Component without harness connected
(Headlight Assembly LH)

OK:
Condition Specified Condition
Battery positive (+) →5 (B)
Battery positive (-) →4 (E)
Turn signal light illuminates


Result:
Result Proceed to
OK (for Outer Rear View Mirror) A
OK (for Front Fender) B
NG (for Halogen Headlight) C
NG (for LED Headlight) D
NG (for Halogen Headlight and LED Headlight) E




A

14.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

B

15.CHECK VEHICLE TYPE

C

D

E

14.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Remove the outer rear view mirror assembly LH.

(See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL)


b.

Inspect the outer rear view mirror assembly LH.

(See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION)



OK

15.CHECK VEHICLE TYPE

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

15.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
except Double Swing Out Type A
for Double Swing Out Type B



A

16.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH

B

17.CHECK VEHICLE TYPE
16.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH
a.

Remove the rear combination light socket and wire subassembly LH (see page Vehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL).


b.

Install the turn signal light bulb to the rear combination light socket and wire sub-assembly LH.


c.
C179946E05
2.125,1.635 2.469,1.635 false 1.854,1.552 1.854,0.573 1.854,0.573 1.948,0.573 false 0.052,0 0.583,0.281 0.531,0.281 10 false *a 2.521,1.563 3.052,1.844 0.531,0.281 10 false E 2.021,0.469 2.552,0.75 0.531,0.281 10 false TRN

Apply battery voltage between the terminals and check the light illumination condition.

Text in Illustration
*a Component without harness connected
(Rear Combination Light Socket and Wire Sub-assembly LH)

OK:
Condition Specified Condition
Battery positive (+) →4 (TRN)
Battery positive (-) →3 (E)
Turn signal light illuminates




OK

17.CHECK VEHICLE TYPE

NG

REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH

17.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Towing Package A
w/o Towing Package B



A

18.CHECK TOWING CONVERTER

B

REPLACE COMBINATION METER ASSEMBLY

18.CHECK TOWING CONVERTER
a.

Replace the towing converter.


b.

Clear the DTCs.


c.

Check for DTCs and check that no DTCs are output.



OK

END (TOWING CONVERTER IS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY

19.CHECK HARNESS AND CONNECTOR (TURN SIGNAL CIRCUIT LH)

*1: except Double Swing Out Type

*2: for Double Swing Out Type

*3: w/ Towing Package


a.

Disconnect the E120 combination meter assembly connector.


b.

Disconnect the A66 headlight assembly LH connector.


c.

Disconnect the I41 outer mirror control ECU assembly LH connector.


d.

Disconnect the K4*1 or n1*2 rear combination light assembly LH connector.


e.

Disconnect the K64 towing converter connector.*3


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-5 (B) - E120-7 (LL) Always Below 1 Ω
A66-4 (E) - Body ground Always Below 1 Ω
I41-11 (TRNI) - E120-7 (LL) Always Below 1 Ω
I41-7 (GND) - Body ground Always Below 1 Ω
K4-4 (TRN) - E120-7 (LL) Always Below 1 Ω
K4-3 (E) - Body ground Always Below 1 Ω
n1-1 (TRN) - E120-7 (LL) Always Below 1 Ω
n1-4 (E) - Body ground Always Below 1 Ω
K64-9 (LTIN) - E120-7 (LL) Always Below 1 Ω
E120-7 (LL) - Body ground Always 10 kΩ or higher




OK

20.CHECK HARNESS AND CONNECTOR (TURN SIGNAL CIRCUIT RH)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

20.CHECK HARNESS AND CONNECTOR (TURN SIGNAL CIRCUIT RH)
a.

Disconnect the I40 outer mirror control ECU assembly LH connector.


b.

Disconnect the I35 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I40-16 (TRN+) - I35-4 (TRNL) Always Below 1 Ω
I40-14 (LE1) - I35-21 (E1) Always Below 1 Ω
I40-16 (TRN+) or I35-4 (TRNL) - I40-14 (LE1) or I35-21 (E1) Always 10 kΩ or higher




OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR