When any of the M1, M2 or M3 switches is pressed, the outer mirror control ECU assembly LH*1, RH*2 sends a switch signal to the main body ECU (multiplex network body ECU) via CAN communication. Then, the main body ECU (multiplex network body ECU) sends a recall request signal to the front power seat switch assembly LH*1, RH*2. The front power seat switch LH*1, RH*2 operates each motor to achieve each memorized position value.
*1: for LHD
*2: for RHD
Before replacing the main body ECU (multiplex network body ECU), refer to the Entry and Start System (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).
Use the GTS to check if the CAN communication system is functioning normally.
for LHD (w/ Central Gateway ECU): See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for LHD (w/o Central Gateway ECU): See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD (w/ Central Gateway ECU): See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD (w/o Central Gateway ECU): See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
CAN communication DTC is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD (w/ Central Gateway ECU)) | B |
| NG (for LHD (w/o Central Gateway ECU)) | C |
| NG (for RHD (w/ Central Gateway ECU)) | D |
| NG (for RHD (w/o Central Gateway ECU)) | E |
A
B
C
D
E
Check that each function of the power seat operates normally by using the switches on the power seat switch (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).
Each function of the power seat operates normally using the switches on the power seat switch.
OK
NG
Perform a memory operation and check that the buzzer sounds to indicate the completion of the memory operation (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).
The seat position will not be recorded if the SET switch and 2 or more of the memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.
If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.
Seat position memory function is normal.
OK
NG
Under each of the following conditions, check that the seat restoring function operates by pressing the M1 switch, M2 switch or M3 switch (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).
Engine switch is off.
The engine switch is on (IG), and park (P) is selected.*1
The engine switch is off within 180 seconds after the driver door is closed and opened.*2
The engine switch is off within 60 seconds after the driver door is opened and closed.*3
| Result | Proceed to |
|---|---|
| Seat restoring function does not operate at all. | A |
| Seat restoring function does not operate when the condition is [*1]. | B |
·
Seat restoring function does not operate when the condition is [*2]. ·
Seat restoring function does not operate when the condition is [*3]. |
C |
A
B
C
Perform the seat position memorized function for the M1, M2 and M3 switch (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Driver Seat / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Seat Memory No1 | Seat position memorized with M1 switch / Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Seat Memory No2 | Seat position memorized with M2 switch / Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Seat Memory No3 | Seat position memorized with M3 switch / Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
Mem appears on the GTS screen.
OK
NG
Temporarily replace the outer mirror control ECU LH*1, RH*2 with a new or normally functioning one (See page Vehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL).
*1: for LHD
*2: for RHD
NEXT
Perform a seat position restoring function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).
Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.
The seat position will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.
If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.
Seat position restoring function operates normally.
OK
NG
Temporarily replace the front power seat switch LH*1, RH*2 with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).
*1: for LHD
*2: for RHD
NEXT
Perform a seat position memory and restoring function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).
Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.
The seat position will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.
If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.
Seat position restoring function operates normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Driver Seat / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Shift SW Position | Park state signal / Shift P or Shift Other | Shift P: Shift lever in P
Shift Other: Shift lever in a position other than P |
- |
On the GTS screen, the item changes between ON and OFF according to the above.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for AB60F) | B |
| NG (for A750F) | C |
| NG (for AE80F) | D |
A
B
C
D
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FL Door Courtesy SW | Front door courtesy light switch assembly LH signal / ON or OFF | ON: Driver door open
OFF: Driver door closed |
for LHD |
| FR Door Courtesy SW | Front door courtesy light switch assembly RH signal / ON or OFF | ON: Driver door open
OFF: Driver door closed |
for RHD |
On the GTS screen, the item changes between ON and OFF according to the above.
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B