Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1422/22  Compressor Lock Sensor Circuit  


SYSTEM DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.

The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the compressor is locked, and turns the magnetic clutch off.

DTC Code DTC Detection Condition Trouble Area
B1422/22 An open or short in the compressor lock sensor circuit.
·

CAN communication line

·

Cooler compressor assembly

·

Harness or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

w/ Rear Heater:


E334401E05
4.688,0.865 5.146,1.104 0.458,0.24 10 false ECM 6.052,1.229 6.531,1.417 0.479,0.188 10 false MGC 5.625,1.354 6.104,1.542 0.479,0.188 10 false E36 5.656,1.115 6.135,1.302 0.479,0.188 10 false 18 6.052,3.792 6.531,3.979 0.479,0.188 10 false LOCK 5.635,3.906 6.115,4.094 0.479,0.188 10 false E35 5.656,3.677 6.135,3.865 0.479,0.188 10 false 30 6.052,4.24 6.531,4.427 0.479,0.188 10 false SG-2 5.646,4.354 6.125,4.542 0.479,0.188 10 false E35 5.667,4.146 6.146,4.333 0.479,0.188 10 false 32 5.583,4.979 7.125,5.51 1.542,0.531 10 false Air Conditioning Amplifier Assembly 0.063,1.333 1.188,1.542 1.125,0.208 10 false from IG1 Relay 1.375,1.479 2.198,1.656 0.823,0.177 10 false A/C COMP 3.125,2.073 3.948,2.25 0.823,0.177 10 false MG CLT 3.708,1.24 4.188,1.427 0.479,0.188 10 false 2 3.708,1.656 4.188,1.844 0.479,0.188 10 false 3 2.948,1.656 3.427,1.844 0.479,0.188 10 false 5 2.927,1.24 3.406,1.427 0.479,0.188 10 false 1 3.979,3.104 4.458,3.292 0.479,0.188 10 false MG+ 4.417,3.104 4.896,3.292 0.479,0.188 10 false 3 3.938,3.802 4.417,3.99 0.479,0.188 10 false SSR+ 4.406,3.802 4.885,3.99 0.479,0.188 10 false 1 3.917,4.24 4.396,4.427 0.479,0.188 10 false SSR- 4.417,4.24 4.896,4.427 0.479,0.188 10 false 2 2.594,3.479 4.24,3.729 1.646,0.25 10 false Magnet Clutch Assembly 2.479,4.719 3.99,4.917 1.51,0.198 10 false C30 0.646,5.396 2.385,5.625 1.74,0.229 10 false : CAN Communication Line 2.469,4.885 4.313,5.135 1.844,0.25 10 false Cooler Compressor Assembly


w/o Rear Heater:


E334419E01
6.055,1.214 6.502,1.392 0.447,0.178 10 MGC 4.685,0.808 5.132,0.987 0.447,0.178 10 ECM 6.055,3.768 6.502,3.946 0.447,0.178 10 LOCK 6.055,4.231 6.502,4.409 0.447,0.178 10 SG-2 1.398,1.46 2.265,1.638 0.867,0.178 10 A/C COMP 3.099,2.023 3.967,2.201 0.867,0.178 10 MG CLT 0.028,1.311 1.047,1.561 1.019,0.251 10 from IG1 Relay 5.509,4.894 5.883,5.073 0.374,0.178 10 E81 5.846,3.768 6.220,3.946 0.374,0.178 10 8 5.776,4.231 6.150,4.409 0.374,0.178 10 13 5.776,1.214 6.150,1.392 0.374,0.178 10 20 3.706,1.214 4.080,1.392 0.374,0.178 10 2 3.706,1.638 4.080,1.816 0.374,0.178 10 3 4.393,3.088 4.767,3.266 0.374,0.178 10 3 4.393,3.788 4.767,3.966 0.374,0.178 10 1 4.393,4.23 4.767,4.409 0.374,0.178 10 2 3.934,3.088 4.308,3.266 0.374,0.178 10 MG+ 3.885,3.788 4.308,3.966 0.423,0.178 10 SSR+ 2.546,3.432 4.181,3.610 1.635,0.178 10 Magnet Clutch Assembly 2.437,4.669 4.468,4.848 2.031,0.178 10 C30 2.437,4.825 4.468,5.004 2.031,0.178 10 Cooler Compressor Assembly 5.509,5.058 7.153,5.460 1.644,0.402 10 Air Conditioning Amplifier Assembly 0.656,5.351 2.686,5.530 2.031,0.178 10 : CAN Communication Line 3.934,4.23 4.308,4.409 0.374,0.178 10 SSR- 2.932,1.214 3.306,1.392 0.374,0.178 10 1 2.932,1.638 3.306,1.816 0.374,0.178 10 5


CAUTION / NOTICE / HINT

NOTICE:
·

ECM malfunctions can affect the storage of this DTC. Therefore, check all ECM DTCs and confirm that the system is normal before performing the following inspection.


·

The air conditioning system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.INSPECT MAGNET CLUTCH ASSEMBLY

A

2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

B

C

D

E

2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

w/ Rear Heater:

i.

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).

U156837E04
2.573,1.073 2.75,1.552 2.75,1.552 3.031,1.552 false 2.208,1.083 2.104,1.573 2.104,1.573 1.823,1.573 false 3.115,1.469 3.573,1.698 0.458,0.229 10 false LOCK 1.458,1.49 1.917,1.719 0.458,0.229 10 false SG-2 2.99,0.781 3.448,1.01 0.458,0.229 10 false E35 4.188,0.792 4.646,1.021 0.458,0.229 10 false GND 0.104,0.042 0.563,0.271 0.458,0.229 10 false *a 3.958,0.042 4.417,0.271 0.458,0.229 10 false *b

Text in Illustration
*a Component with harness connected
((Air Conditioning Amplifier Assembly)
*b Waveform


ii.

Measure the waveform of the connector.

Measurement Condition
Item Contents
Terminal No. (Symbol) E35-30 (LOCK) - E35-32 (SG-2)
Tool Setting 200 mV/DIV., 10 ms/DIV.
Condition
·

Engine idling

·

A/C switch on

·

Blower switch LO





b.

w/o Rear Heater:

U166594E01
0.094,0.072 0.363,0.234 0.269,0.162 10 *a 4.354,0.072 4.623,0.234 0.269,0.162 10 *b 1.39,0.234 1.807,0.397 0.417,0.162 10 LOCK 1.81,0.302 1.991,0.302 1.991,0.302 2.157,0.971 false 1.164,0.467 1.528,0.630 0.364,0.162 10 SG-2 2.206,0.404 2.488,0.566 0.282,0.162 10 E81 4.168,0.826 4.510,0.988 0.341,0.162 10 GND 1.529,0.537 1.709,0.537 1.709,0.537 1.903,0.967 false

Text in Illustration
*a Component with harness connected
((Air Conditioning Amplifier Assembly)
*b Waveform

i.

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


ii.

Measure the waveform of the connector.

Measurement Condition
Item Contents
Terminal No. (Symbol) E81-8 (LOCK) - E81-13 (SG-2)
Tool Setting 200 mV/DIV., 10 ms/DIV.
Condition Engine running
A/C switch on
Blower switch LO




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

3.INSPECT COOLER COMPRESSOR ASSEMBLY
3.INSPECT COOLER COMPRESSOR ASSEMBLY

A

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY -COOLER COMPRESSOR ASSEMBLY)

B

C

D

E

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY -COOLER COMPRESSOR ASSEMBLY)
a.

w/ Rear Heater:

i.

Disconnect the E35 air conditioning amplifier assembly connector.


ii.

Disconnect the C30 cooler compressor assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E35-30 (LOCK) - C30-1 (SSR+) Always Below 1 Ω
E35-32 (SG-2) - C30-2 (SSR-) Always Below 1 Ω
C30-1 (SSR+) - C30-2 (SSR-) Always 10 kΩ or higher
E35-30 (LOCK) or C30-1 (SSR+) - Body ground Always 10 kΩ or higher
E35-32 (SG-2) or C30-2 (SSR-) - Body ground Always 10 kΩ or higher




b.

w/o Rear Heater:

i.

Disconnect the E81 air conditioning amplifier assembly connector.


ii.

Disconnect the C30 cooler compressor assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E81-8 (LOCK) - C30-1 (SSR+) Always Below 1 Ω
E81-13 (SG-2) - C30-2 (SSR-) Always Below 1 Ω
C30-1 (SSR+) - C30-2 (SSR-) Always Below 1 Ω
E81-8 (LOCK) or C30-1 (SSR+) - Body ground Always 10 kΩ or higher
E81-13 (SG-2) or C30-2 (SSR-) - Body ground Always 10 kΩ or higher





OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR