Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2015.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255724 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the road sign assist system, lane departure alert system, forward recognition camera system, dynamic radar cruise control system, pre-crash safety system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 56115C 1.INSTALL WINDSHIELD GLASS STOPPER

a.
B449329E02
1.771,0.573 1.771,0.417 1.771,0.417 2.302,0.417 false 0.323,1.094 0.323,0.938 0.323,0.938 0.552,0.938 false 0.271,1.135 0.563,1.375 0.292,0.24 10 false *2 1.708,0.625 1.979,0.844 0.271,0.219 10 false *1

Install 2 new stoppers to the vehicle body as shown in the illustration.

Text in Illustration
*1 Vehicle Body
*2 Stopper


Hide 56116C 2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER

a.

Apply Primer G to the glass where the stopper will be installed.

NOTICE:
·

Allow the Primer G to dry for 3 minutes or more.

·

Throw away any leftover Primer G.

·

Do not apply too much Primer G.




b.

Install 2 new stoppers onto the glass as shown in the illustration.

B183899E08
0.542,1.156 0.646,0.771 0.646,0.771 0.865,0.771 false 1.438,1.427 1.583,0.74 1.583,0.74 1.802,0.74 false 0.427,1.427 0.51,2.021 false 5.052,1.427 5.135,2.021 false 6.125,1.448 6.271,0.76 6.271,0.76 6.49,0.76 false 5.146,1.188 5.25,0.802 5.25,0.802 5.469,0.802 false 0.135,0.125 0.417,0.344 0.281,0.219 10 false *a 1.844,0.646 2.125,0.865 0.281,0.219 10 false *b 0.917,0.698 1.198,0.917 0.281,0.219 10 false *1 0.458,2.031 0.74,2.25 0.281,0.219 10 false *c 2.052,1.781 2.333,2 0.281,0.219 10 false a 5.094,2.042 5.375,2.26 0.281,0.219 10 false *c 6.708,1.792 6.99,2.01 0.281,0.219 10 false a 6.531,0.677 6.813,0.896 0.281,0.219 10 false *b 5.51,0.74 5.792,0.958 0.281,0.219 10 false *1

Text in Illustration
*1 Windshield Glass - -
*a Back of Windshield Glass *b Ceramic Notch
*c Ceramic Line - -

Standard:
Area Specified Condition
a 13.2 mm (0.520 in.)



Hide 75533G 3.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Using a brush or sponge, coat the contact surface of the glass and moulding with Primer G as shown in the illustration.

NOTICE:
·

Allow the Primer G coating to dry for 3 minutes or more.

·

Do not coat the adhesive with Primer G.

·

Throw away any leftover Primer G.



B183901E06
0.146,0.094 0.427,0.385 0.281,0.292 10 false *a 3.521,0.5 3.656,0.698 0.135,0.198 10 false A 3.51,0.938 3.646,1.135 0.135,0.198 10 false A 5.51,0.625 6.073,0.854 0.563,0.229 10 false A - A

Text in Illustration
*a Back of Windshield Glass - -

NOTICE:

Do not drive the vehicle for the amount of time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



b.

Remove the peeling paper from the windshield outside moulding. Install the moulding as shown in the illustration.


Hide 56117D 4.INSTALL WINDSHIELD GLASS ADHESIVE DAM

a.

Apply Primer G to the glass where the glass adhesive dam will be installed.

NOTICE:
·

Allow the Primer G to dry for 3 minutes or more.

·

Throw away any leftover Primer G.

·

Do not apply too much Primer G.




b.

Remove the peeling paper from the adhesive part of the dam. Install the dam (adhesive side) to the glass (Primer G area), but exclude the area above the notches on the upper part of the glass.

U155822E04
6.26,1.375 6.26,1.677 false 6.271,2.51 6.271,2.802 false 0.646,1.104 0.479,0.906 false 0.677,1.24 1.063,1.177 false 1.188,2.969 0.979,2.625 false 4.99,1.083 5.156,0.917 false 4.969,1.24 4.583,1.177 false 4.385,3.021 4.604,2.677 false 5.583,0.948 6.063,1.188 0.479,0.24 10 false A - A 5.563,2.156 6.042,2.385 0.479,0.229 10 false B - B 3.042,2.625 3.271,2.823 0.229,0.198 10 false B 3.042,2.25 3.271,2.448 0.229,0.198 10 false B 3.646,1.844 3.885,2.052 0.24,0.208 10 false A 1.479,2.052 1.719,2.26 0.24,0.208 10 false A 4.063,1.792 4.302,2 0.24,0.208 10 false A 1.896,2.135 2.135,2.344 0.24,0.208 10 false A 6.198,2.844 6.49,3.073 0.292,0.229 10 false *c 6.208,1.74 6.5,1.969 0.292,0.229 10 false *c 1.104,1.094 1.396,1.323 0.292,0.229 10 false *c 0.844,2.458 1.135,2.688 0.292,0.229 10 false *c 0.313,0.76 0.604,0.99 0.292,0.229 10 false *b 0.604,3.156 0.844,3.365 0.24,0.208 10 false *b 0.083,0.073 0.375,0.302 0.292,0.229 10 false *a 4.396,1.063 4.688,1.292 0.292,0.229 10 false *c 4.604,2.479 4.896,2.708 0.292,0.229 10 false *c 5.177,0.813 5.469,1.042 0.292,0.229 10 false *b 4.917,3.094 5.208,3.323 0.292,0.229 10 false *b

Text in Illustration
*a Back of Windshield Glass *b Ceramic Notch
*c Dam Center Line - -


Hide 56165 5.INSTALL FRONT INNER WINDOW MOULDING COVER LH

a.

Using a knife, cut off the cover as shown in the illustration.

B183903E02
2.04,1.582 2.492,1.775 0.452,0.193 10 A - A 4.843,1.582 5.295,1.775 0.452,0.193 10 B - B 2.402,0.132 2.537,0.314 0.135,0.182 10 A 2.402,0.959 2.537,1.141 0.135,0.182 10 A 6.766,0.676 6.931,0.860 0.165,0.184 10 a 2.618,1.379 2.741,1.558 0.123,0.179 10 b 5.09,0.132 5.224,0.314 0.135,0.182 10 B 5.09,0.959 5.224,1.141 0.135,0.182 10 B 5.947,1.29 6.143,1.467 0.197,0.177 10 *a 5.33,2.252 5.662,2.252 false 6.016,1.275 6.016,0.804 false 4.075,1.379 4.198,1.558 0.123,0.179 10 c 5.69,2.168 5.886,2.345 0.197,0.177 10 *a

Text in Illustration
*a Cut Area - -

Standard:
Area Specified Condition
a 6.9 mm (0.272 in.)
b 96.5 mm (3.79 in.)
c 10.0 mm (o.394 in.)



b.

Apply Primer G to the glass where the inner window moulding cover will be installed.

NOTICE:
·

Allow the Primer G to dry for 3 minutes or more.

·

Throw away any leftover Primer G.

·

Do not apply too much Primer G.




c.

Remove the peeling paper from the inner window moulding cover. Install the cover to the glass, as shown in the illustration.

U155823E04
2.604,1.667 2.604,0.656 false 4.51,0.656 4.677,0.656 4.677,0.656 4.677,1.302 false 1.875,1.719 2.396,2.458 2.396,2.458 2.938,2.458 false 1.896,2.208 2.052,2.365 0.156,0.156 10 false A 1,2.104 1.25,2.365 0.25,0.26 10 false a 2.135,1.01 2.292,1.167 0.156,0.156 10 false A 3.594,0.146 4.021,0.365 0.427,0.219 10 false A - A 3.146,0.594 3.479,0.854 0.333,0.26 10 false *b 3.938,0.583 4.271,0.844 0.333,0.26 10 false *b 0.146,0.073 0.479,0.333 0.333,0.26 10 false *a 2.99,2.375 3.323,2.635 0.333,0.26 10 false *c 4.521,2.354 4.854,2.615 0.333,0.26 10 false *c

Text in Illustration
*a Back of Windshield Glass *b Ceramic Line
*c Ceramic Notch for ID-Plate - -

Standard:
Area Specified Condition
a 14.0 mm (0.551 in.)



Hide 56111 6.INSTALL WINDSHIELD GLASS

a.
B436427E03
1.771,1.646 1.958,1.771 false 1.99,1.708 2.24,2 0.25,0.292 10 false *a

Position the glass.

Text in Illustration
*a Matchmarks

i.

Using suction cups, place the glass in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.

Place matchmarks on the glass and vehicle body on the locations indicated in the illustration.

HINT:
·

Placing matchmarks is only necessary when installing new glass. If it is the reused glass, matchmarks should already be present.

·

When reusing the glass, check and correct the matchmark positions.



NOTICE:

Check that the stoppers are attached to the vehicle body correctly.



iv.

Using suction cups, remove the glass.



b.
B436429E04
2.292,2.25 2.125,2.469 2.125,2.469 2.031,2.469 false 2.375,2.083 2.052,1.844 2.052,1.844 1.906,1.844 false 2.385,1.052 2.063,0.823 2.063,0.823 1.917,0.823 false 1.427,0.24 1.708,0.521 0.281,0.281 10 false *a 1.354,1.969 1.635,2.25 0.281,0.281 10 false *b 1.708,1.76 1.99,2.042 0.281,0.281 10 false *1 1.854,2.385 2.135,2.667 0.281,0.281 10 false *2 0.573,4.333 0.854,4.615 0.281,0.281 10 false *1 1.74,0.729 2.021,1.01 0.281,0.281 10 false *1

Using a brush, apply Primer M to the exposed part of the vehicle body.

Text in Illustration
*1 Primer M
*2 Adhesive
*a CORRECT
*b INCORRECT

NOTICE:
·

Allow the Primer M to dry for 3 minutes or more.

·

Do not apply Primer M to the adhesive.

·

Throw away any leftover Primer M.

·

Do not apply too much Primer M.




c.

Using a brush or sponge, apply Primer G to the contact surface of the glass.

B183905E05
0.844,1.823 0.844,2.052 false 4.01,0.813 4.25,1.052 false 5.698,0.802 5.302,1.063 false 3.958,1.979 4.427,2.115 false 6.021,1.927 5.167,2.198 5.167,2.198 5.729,1.927 false 0.094,0.063 0.365,0.344 0.271,0.281 10 false *a 0.625,0.438 0.76,0.625 0.135,0.188 10 false B 2.042,0.427 2.156,0.573 0.115,0.146 10 false B 2.042,0.792 2.167,0.948 0.125,0.156 10 true B 0.604,0.729 0.719,0.875 0.115,0.146 10 true B 0.583,1.302 0.698,1.448 0.115,0.146 10 false C 1.302,0.448 1.438,0.635 0.135,0.188 10 false A 1.302,0.771 1.417,0.917 0.115,0.146 10 true A 2.51,1.51 2.625,1.656 0.115,0.146 10 false D 2.573,1.896 2.688,2.042 0.115,0.146 10 false D 2.417,0.875 2.531,1.021 0.115,0.146 10 false C 2.823,0.781 2.938,0.927 0.115,0.146 10 false C 0.313,1.24 0.427,1.385 0.115,0.146 10 false C 3.344,0.438 3.698,0.604 0.354,0.167 10 false A - A 5.24,0.354 5.573,0.5 0.333,0.146 10 false B - B 3.323,1.49 3.677,1.635 0.354,0.146 10 false C - C 5.26,1.396 5.615,1.542 0.354,0.146 10 false D - D 0.781,2.115 1.073,2.323 0.292,0.208 10 false *b 5.302,2.219 5.406,2.365 0.104,0.146 10 false d 3.542,1.208 3.688,1.385 0.146,0.177 10 false b 6.448,2.354 6.552,2.5 0.104,0.146 10 false b 6.323,1.521 6.427,1.667 0.104,0.146 10 false e 3.594,2.177 3.698,2.323 0.104,0.146 10 false c 4.5,0.427 4.635,0.615 0.135,0.188 10 false a 6.219,0.99 6.323,1.135 0.104,0.146 10 false a 4.458,2.052 4.75,2.26 0.292,0.208 10 false *b 4.271,1.063 4.563,1.271 0.292,0.208 10 false *b 0.542,2.469 0.833,2.677 0.292,0.208 10 false *1 5.135,1.031 5.427,1.24 0.292,0.208 10 false *b 5.01,2.146 5.302,2.354 0.292,0.208 10 false *b

Text in Illustration
*1 Primer G - -
*a Back of Windshield Glass *b Adhesive Center Line

Standard:
Area Specified Condition
a 9.0 mm (0.354 in.)
b 7.0 mm (0.276 in.)
c 3.0 mm (0.118 in.)
d 4.0 mm (0.157 in.)
e 8.0 mm (0.315 in.)


HINT:

If the Primer G is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.


NOTICE:
·

Allow the Primer G to dry for 3 minutes or more.

·

Throw away any leftover Primer G.

·

Do not apply too much Primer G.




d.
B183900E02
0.631,1.496 0.817,1.664 0.186,0.168 10 *1 1.338,1.151 0.715,1.151 0.715,1.151 0.715,1.451 false

Using a brush or sponge, coat the windshield outside moulding with Primer G as shown in the illustration.

Text in Illustration
*1 Primer G

NOTICE:
·

Allow the Primer G to dry for 3 minutes or more.

·

Throw away any leftover Primer G.

·

Do not apply too much Primer G.




e.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of the cartridge nozzle as shown in the illustration.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the glass as shown in the illustration.

U155824E05
2.313,1.833 2.313,2.052 false 5.792,0.979 5.792,1.104 false 6.156,2.271 6.531,2.083 false 5.781,2.313 5.781,2.448 false 0.083,0.094 0.479,0.302 0.396,0.208 10 false *a 2.052,0.406 2.167,0.552 0.115,0.146 10 false B 3.49,0.438 3.604,0.583 0.115,0.146 10 false B 3.5,0.771 3.615,0.938 0.115,0.167 10 true B 2.021,0.729 2.146,0.885 0.125,0.156 10 true B 2.021,1.292 2.135,1.438 0.115,0.146 10 false C 2.75,0.427 2.865,0.573 0.115,0.146 10 false A 2.75,0.76 2.865,0.906 0.115,0.146 10 true A 3.938,1.51 4.052,1.656 0.115,0.146 10 false D 3.99,1.885 4.104,2.031 0.115,0.146 10 false D 3.865,0.875 3.979,1.021 0.115,0.146 10 false C 4.271,0.823 4.385,0.969 0.115,0.146 10 false C 1.76,1.26 1.875,1.406 0.115,0.146 10 false C 4.448,0.073 4.781,0.219 0.333,0.146 10 false A - A 5.833,0.073 6.167,0.219 0.333,0.146 10 false B - B 4.448,1.385 4.802,1.531 0.354,0.146 10 false C - C 5.823,1.385 6.177,1.531 0.354,0.146 10 false D - D 2.25,2.083 2.542,2.344 0.292,0.26 10 false *b 1.073,2.469 1.354,2.667 0.281,0.198 10 false *1 5.208,1.458 5.313,1.604 0.104,0.146 10 false d 0.656,2.094 0.76,2.24 0.104,0.146 10 false b 0.99,1.74 1.094,1.885 0.104,0.146 10 false b 6.375,1.469 6.479,1.615 0.104,0.146 10 false b 6.563,0.167 6.667,0.313 0.104,0.146 10 false c 5.25,0.156 5.354,0.302 0.104,0.146 10 false c 0.24,2.427 0.344,2.573 0.104,0.146 10 false a 0.521,1.5 0.625,1.646 0.104,0.146 10 false a 5.698,2.479 6.198,2.688 0.5,0.208 10 false *b 5.729,1.135 6.156,1.427 0.427,0.292 10 false *b

Text in Illustration
*1 Adhesive - -
*a Back of Windshield Glass *b Adhesive Center Line

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 9.0 mm (0.354 in.)
d 3.0 mm (0.118 in.)




f.
B183907E02
1.141,1.753 1.376,1.915 0.235,0.161 10 *a 1.631,1.132 1.254,1.132 1.254,1.132 1.254,1.706 false 1.644,1.411 1.254,1.411 false

Install the glass to the vehicle body.

Text in Illustration
*a Matchmarks

i.

Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.


ii.

Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.

NOTICE:
·

Check that the stoppers are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.




iii.

Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.

NOTICE:

Do not drive the vehicle for the amount of time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




g.
E271513E01
0.71,1.78 0.826,1.925 0.116,0.145 10 A

w/o Heated Windshield Defroster:

i.

Connect the connector A.

HINT:

w/o Heated Windshield Defroster:

The vehicle only has connector A.




h.

w/ Heated Windshield Defroster:

i.

Connect the 3 connectors.



Hide 56111 7.CHECK FOR LEAK AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 63310 8.INSTALL ROOF HEADLINING

a.

w / Sliding Roof:

i.

Return the roof headlining to its original position. Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/ Sliding Roof)>INSTALLATION).



b.

w /o Sliding Roof:

i.

Return the roof headlining to its original position. Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/o Sliding Roof)>INSTALLATION).



Hide 89941 9.INSTALL RAIN SENSOR (w/ Rain Sensor)

Hide 87810 10.INSTALL INNER REAR VIEW MIRROR ASSEMBLY

Hide 86401 11.INSTALL FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY (w/ Pre-crash Safety System, Camera Heater)

Hide 8646C 12.INSTALL FORWARD RECOGNITION CAMERA (w/ Pre-crash Safety System)

Hide 86464A 13.INSTALL FORWARD RECOGNITION LATCH (w/ Pre-crash Safety System)

Hide 86466D 14.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 86466E 15.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 75561A 26.INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP

HINT:

Perform the following procedures if replacing any roof drip side finish moulding clip.


NOTICE:

Remove the double-sided tape where the clips will be installed on the body and clean the body with a non-residue type solvent.


B187426E02
2.064,0.824 2.371,0.824 false 1.851,0.727 2.080,0.914 0.229,0.187 10 *1 0.784,0.961 0.988,1.159 0.205,0.198 10 *a 0.986,1.073 1.226,1.073 1.226,1.073 1.347,1.528 false

Text in Illustration
*1 Adhesive
*a 2 to 3 mm Bead of Adhesive

a.

Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to a new roof drip side finish moulding clip.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140 kgf/cm2, 1991 psi) or more when the temperature is 23°C (73°F).



b.

Apply Primer G to the body where the roof drip side finish moulding clip will be installed.

NOTICE:

Do not let the Primer G dry.



c.
B189691E01
0.669,2.636 0.780,2.810 0.111,0.174 10 a 2.294,2.631 2.404,2.804 0.111,0.174 10 c 2.759,2.631 2.869,2.804 0.111,0.174 10 d 1.11,2.631 1.221,2.804 0.111,0.174 10 b

Install the clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the roof drip side finish moulding clip after lightly applying adhesive (3M DP-105 or equivalent).

Standard:
Area Specified Condition
a 2.5 to 12.5 mm (0.0984 to 0.492 in.)
b 6.5 to 16.5 mm (0.256 to 0.650 in.)
c 0 to 6.0 mm (0 to 0.236 in.)
d 4.0 to 10.0 mm (0.157 to 0.394 in.)



d.

Install the windshield outside moulding when 40 minutes or more have elapsed after pressing and installing the roof drip side finish moulding clip.

HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 48 hours




Hide 75547B 27.INSTALL NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedures if replacing any No. 3 windshield outside moulding clip(s).


a.

Install a nose piece to an air riveter or hand riveter.


b.

Insert the mandrel part of a new No. 3 windshield outside moulding clip into the nose piece.


c.
B180571

Using the riveter, install the No. 3 windshield outside moulding clip(s) shown in the illustration.

HINT:

If the rivet cannot be cut, pull it once and cut it.


NOTICE:
·
B171664E51
1.031,1.031 0.5,1.615 0.5,1.615 1.042,2.24 false 1.74,0.917 2.594,1.781 2.594,1.781 1.76,2.521 false 2.271,0.542 2.552,0.729 0.281,0.188 10 false *a 2.083,2.469 2.802,2.667 0.719,0.198 10 false *b 0.302,1.521 0.51,1.74 0.208,0.219 10 false *1 2.656,1.698 2.906,1.917 0.25,0.219 10 false *2

Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

Text in Illustration
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT

·
B172390E28
2.325,0.536 2.513,0.713 0.188,0.177 10 *a 2.325,1.527 2.499,1.704 0.175,0.177 10 *a 2.434,2.73 2.634,2.907 0.200,0.177 10 *b 0.72,0.066 1.023,0.066 false 0.818,1.11 1.018,1.11 false 1.043,2.324 1.223,2.477 0.180,0.152 10 *1 1.043,1.044 1.223,1.196 0.180,0.152 10 *1 1.043,0.004 1.223,0.156 0.180,0.152 10 *1 0.818,2.402 1.018,2.402 false

Confirm that the riveter are seated properly against the moulding.

Text in Illustration
*1 Riveter
*a INCORRECT
*b CORRECT

·

Do not tilt the riveter when installing the rivet to the moulding.

·

Do not leave any space between the rivet head and moulding.

·
B172391E25
2.304,0.996 2.503,1.173 0.200,0.177 10 *a 2.408,2.434 2.619,2.611 0.211,0.177 10 *b 0.978,0.515 1.172,0.685 0.195,0.171 10 *1 0.735,0.603 0.941,0.603 false 0.973,2.023 1.182,2.194 0.208,0.171 10 *1 0.731,2.111 0.937,2.111 false

Do not leave any space between the moulding and body. Firmly hold together the 2 items while installing the rivet.

Text in Illustration
*1 Riveter
*a INCORRECT
*b CORRECT




Hide 75548C 28.INSTALL NO. 4 WINDSHIELD MOULDING PAD

a.
B180566

Install the 4 new No. 4 moulding pads.

HINT:

Use the same procedure to install the 4 windshield moulding pads on the other side.



Hide 75534 29.INSTALL WINDSHIELD OUTSIDE MOULDING LH

a.
B180565

Attach the 6 clips to install the new moulding.


b.

Remove the protective tape from the edges of the moulding.


Hide 75533 30.INSTALL WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 55781E 31.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53883F 32.INSTALL FRONT FENDER MAIN SEAL LH

Hide 53882H 33.INSTALL FRONT FENDER MAIN SEAL RH

Hide 28800 35.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 36.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 37.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 8646C 38.ADJUST FORWARD RECOGNITION CAMERA

a.

If the forward recognition camera has been replaced with a new one or the windshield glass has been removed and installed, it is necessary to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

See pageEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT